Add/Update/Sync device tree descriptions for Xilinx boards.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
dtb-$(CONFIG_ARCH_ZYNQMP) += zynqmp-zc1232-revA.dtb
dtb-$(CONFIG_ARCH_ZYNQMP) += zynqmp-zc1254-revA.dtb
dtb-$(CONFIG_ARCH_ZYNQMP) += zynqmp-zc1275-revA.dtb
+dtb-$(CONFIG_ARCH_ZYNQMP) += zynqmp-zc1275-revB.dtb
+dtb-$(CONFIG_ARCH_ZYNQMP) += zynqmp-zc1285-revA.dtb
dtb-$(CONFIG_ARCH_ZYNQMP) += zynqmp-zc1751-xm015-dc1.dtb
dtb-$(CONFIG_ARCH_ZYNQMP) += zynqmp-zc1751-xm016-dc2.dtb
dtb-$(CONFIG_ARCH_ZYNQMP) += zynqmp-zc1751-xm017-dc3.dtb
dtb-$(CONFIG_ARCH_ZYNQMP) += zynqmp-zcu102-revB.dtb
dtb-$(CONFIG_ARCH_ZYNQMP) += zynqmp-zcu102-rev1.0.dtb
dtb-$(CONFIG_ARCH_ZYNQMP) += zynqmp-zcu104-revA.dtb
+dtb-$(CONFIG_ARCH_ZYNQMP) += zynqmp-zcu104-revC.dtb
dtb-$(CONFIG_ARCH_ZYNQMP) += zynqmp-zcu106-revA.dtb
dtb-$(CONFIG_ARCH_ZYNQMP) += zynqmp-zcu111-revA.dtb
--- /dev/null
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Clock specification for Xilinx ZynqMP
+ *
+ * (C) Copyright 2017, Xilinx, Inc.
+ *
+ * Michal Simek <michal.simek@xilinx.com>
+ */
+
+#include <dt-bindings/clock/xlnx-zynqmp-clk.h>
+/ {
+ fclk0: fclk0 {
+ status = "okay";
+ compatible = "xlnx,fclk";
+ clocks = <&zynqmp_clk PL0_REF>;
+ };
+
+ fclk1: fclk1 {
+ status = "okay";
+ compatible = "xlnx,fclk";
+ clocks = <&zynqmp_clk PL1_REF>;
+ };
+
+ fclk2: fclk2 {
+ status = "okay";
+ compatible = "xlnx,fclk";
+ clocks = <&zynqmp_clk PL2_REF>;
+ };
+
+ fclk3: fclk3 {
+ status = "okay";
+ compatible = "xlnx,fclk";
+ clocks = <&zynqmp_clk PL3_REF>;
+ };
+
+ pss_ref_clk: pss_ref_clk {
+ u-boot,dm-pre-reloc;
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <33333333>;
+ };
+
+ video_clk: video_clk {
+ u-boot,dm-pre-reloc;
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <27000000>;
+ };
+
+ pss_alt_ref_clk: pss_alt_ref_clk {
+ u-boot,dm-pre-reloc;
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <0>;
+ };
+
+ gt_crx_ref_clk: gt_crx_ref_clk {
+ u-boot,dm-pre-reloc;
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <108000000>;
+ };
+
+ aux_ref_clk: aux_ref_clk {
+ u-boot,dm-pre-reloc;
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <27000000>;
+ };
+
+ dp_aclk: dp_aclk {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <100000000>;
+ clock-accuracy = <100>;
+ };
+};
+
+&zynqmp_firmware {
+ zynqmp_clk: clock-controller {
+ u-boot,dm-pre-reloc;
+ #clock-cells = <1>;
+ compatible = "xlnx,zynqmp-clk";
+ clocks = <&pss_ref_clk>, <&video_clk>, <&pss_alt_ref_clk>,
+ <&aux_ref_clk>, <>_crx_ref_clk>;
+ clock-names = "pss_ref_clk", "video_clk", "pss_alt_ref_clk",
+ "aux_ref_clk", "gt_crx_ref_clk";
+ };
+};
+
+&can0 {
+ clocks = <&zynqmp_clk CAN0_REF>, <&zynqmp_clk LPD_LSBUS>;
+};
+
+&can1 {
+ clocks = <&zynqmp_clk CAN1_REF>, <&zynqmp_clk LPD_LSBUS>;
+};
+
+&cpu0 {
+ clocks = <&zynqmp_clk ACPU>;
+};
+
+&fpd_dma_chan1 {
+ clocks = <&zynqmp_clk GDMA_REF>, <&zynqmp_clk LPD_LSBUS>;
+};
+
+&fpd_dma_chan2 {
+ clocks = <&zynqmp_clk GDMA_REF>, <&zynqmp_clk LPD_LSBUS>;
+};
+
+&fpd_dma_chan3 {
+ clocks = <&zynqmp_clk GDMA_REF>, <&zynqmp_clk LPD_LSBUS>;
+};
+
+&fpd_dma_chan4 {
+ clocks = <&zynqmp_clk GDMA_REF>, <&zynqmp_clk LPD_LSBUS>;
+};
+
+&fpd_dma_chan5 {
+ clocks = <&zynqmp_clk GDMA_REF>, <&zynqmp_clk LPD_LSBUS>;
+};
+
+&fpd_dma_chan6 {
+ clocks = <&zynqmp_clk GDMA_REF>, <&zynqmp_clk LPD_LSBUS>;
+};
+
+&fpd_dma_chan7 {
+ clocks = <&zynqmp_clk GDMA_REF>, <&zynqmp_clk LPD_LSBUS>;
+};
+
+&fpd_dma_chan8 {
+ clocks = <&zynqmp_clk GDMA_REF>, <&zynqmp_clk LPD_LSBUS>;
+};
+
+&gpu {
+ clocks = <&zynqmp_clk GPU_REF>, <&zynqmp_clk GPU_PP0_REF>, <&zynqmp_clk GPU_PP1_REF>;
+};
+
+&lpd_dma_chan1 {
+ clocks = <&zynqmp_clk ADMA_REF>, <&zynqmp_clk LPD_LSBUS>;
+};
+
+&lpd_dma_chan2 {
+ clocks = <&zynqmp_clk ADMA_REF>, <&zynqmp_clk LPD_LSBUS>;
+};
+
+&lpd_dma_chan3 {
+ clocks = <&zynqmp_clk ADMA_REF>, <&zynqmp_clk LPD_LSBUS>;
+};
+
+&lpd_dma_chan4 {
+ clocks = <&zynqmp_clk ADMA_REF>, <&zynqmp_clk LPD_LSBUS>;
+};
+
+&lpd_dma_chan5 {
+ clocks = <&zynqmp_clk ADMA_REF>, <&zynqmp_clk LPD_LSBUS>;
+};
+
+&lpd_dma_chan6 {
+ clocks = <&zynqmp_clk ADMA_REF>, <&zynqmp_clk LPD_LSBUS>;
+};
+
+&lpd_dma_chan7 {
+ clocks = <&zynqmp_clk ADMA_REF>, <&zynqmp_clk LPD_LSBUS>;
+};
+
+&lpd_dma_chan8 {
+ clocks = <&zynqmp_clk ADMA_REF>, <&zynqmp_clk LPD_LSBUS>;
+};
+
+&nand0 {
+ clocks = <&zynqmp_clk NAND_REF>, <&zynqmp_clk LPD_LSBUS>;
+};
+
+&gem0 {
+ clocks = <&zynqmp_clk LPD_LSBUS>, <&zynqmp_clk GEM0_REF>, <&zynqmp_clk GEM0_TX>,
+ <&zynqmp_clk GEM0_RX>, <&zynqmp_clk GEM_TSU>;
+ clock-names = "pclk", "hclk", "tx_clk", "rx_clk", "tsu_clk";
+};
+
+&gem1 {
+ clocks = <&zynqmp_clk LPD_LSBUS>, <&zynqmp_clk GEM1_REF>, <&zynqmp_clk GEM1_TX>,
+ <&zynqmp_clk GEM1_RX>, <&zynqmp_clk GEM_TSU>;
+ clock-names = "pclk", "hclk", "tx_clk", "rx_clk", "tsu_clk";
+};
+
+&gem2 {
+ clocks = <&zynqmp_clk LPD_LSBUS>, <&zynqmp_clk GEM2_REF>, <&zynqmp_clk GEM2_TX>,
+ <&zynqmp_clk GEM2_RX>, <&zynqmp_clk GEM_TSU>;
+ clock-names = "pclk", "hclk", "tx_clk", "rx_clk", "tsu_clk";
+};
+
+&gem3 {
+ clocks = <&zynqmp_clk LPD_LSBUS>, <&zynqmp_clk GEM3_REF>, <&zynqmp_clk GEM3_TX>,
+ <&zynqmp_clk GEM3_RX>, <&zynqmp_clk GEM_TSU>;
+ clock-names = "pclk", "hclk", "tx_clk", "rx_clk", "tsu_clk";
+};
+
+&gpio {
+ clocks = <&zynqmp_clk LPD_LSBUS>;
+};
+
+&i2c0 {
+ clocks = <&zynqmp_clk I2C0_REF>;
+};
+
+&i2c1 {
+ clocks = <&zynqmp_clk I2C1_REF>;
+};
+
+&perf_monitor_ocm {
+ clocks = <&zynqmp_clk LPD_LSBUS>;
+};
+
+&perf_monitor_ddr {
+ clocks = <&zynqmp_clk TOPSW_LSBUS>;
+};
+
+&perf_monitor_cci {
+ clocks = <&zynqmp_clk TOPSW_LSBUS>;
+};
+
+&perf_monitor_lpd {
+ clocks = <&zynqmp_clk LPD_LSBUS>;
+};
+
+&pcie {
+ clocks = <&zynqmp_clk PCIE_REF>;
+};
+
+&qspi {
+ clocks = <&zynqmp_clk QSPI_REF>, <&zynqmp_clk LPD_LSBUS>;
+};
+
+&sata {
+ clocks = <&zynqmp_clk SATA_REF>;
+};
+
+&sdhci0 {
+ clocks = <&zynqmp_clk SDIO0_REF>, <&zynqmp_clk LPD_LSBUS>;
+};
+
+&sdhci1 {
+ clocks = <&zynqmp_clk SDIO1_REF>, <&zynqmp_clk LPD_LSBUS>;
+};
+
+&spi0 {
+ clocks = <&zynqmp_clk SPI0_REF>, <&zynqmp_clk LPD_LSBUS>;
+};
+
+&spi1 {
+ clocks = <&zynqmp_clk SPI1_REF>, <&zynqmp_clk LPD_LSBUS>;
+};
+
+&ttc0 {
+ clocks = <&zynqmp_clk LPD_LSBUS>;
+};
+
+&ttc1 {
+ clocks = <&zynqmp_clk LPD_LSBUS>;
+};
+
+&ttc2 {
+ clocks = <&zynqmp_clk LPD_LSBUS>;
+};
+
+&ttc3 {
+ clocks = <&zynqmp_clk LPD_LSBUS>;
+};
+
+&uart0 {
+ clocks = <&zynqmp_clk UART0_REF>, <&zynqmp_clk LPD_LSBUS>;
+};
+
+&uart1 {
+ clocks = <&zynqmp_clk UART1_REF>, <&zynqmp_clk LPD_LSBUS>;
+};
+
+&usb0 {
+ clocks = <&zynqmp_clk USB0_BUS_REF>, <&zynqmp_clk USB3_DUAL_REF>;
+};
+
+&usb1 {
+ clocks = <&zynqmp_clk USB1_BUS_REF>, <&zynqmp_clk USB3_DUAL_REF>;
+};
+
+&watchdog0 {
+ clocks = <&zynqmp_clk WDT>;
+};
+
+&lpd_watchdog {
+ clocks = <&zynqmp_clk LPD_WDT>;
+};
+
+&xilinx_ams {
+ clocks = <&zynqmp_clk AMS_REF>;
+};
+
+&zynqmp_dpsub {
+ clocks = <&dp_aclk>, <&zynqmp_clk DP_AUDIO_REF>, <&zynqmp_clk DP_VIDEO_REF>;
+};
+
+&xlnx_dpdma {
+ clocks = <&zynqmp_clk DPDMA_REF>;
+};
+
+&zynqmp_dp_snd_codec0 {
+ clocks = <&zynqmp_clk DP_AUDIO_REF>;
+};
+
+&pcap {
+ clocks = <&zynqmp_clk PCAP>;
+};
compatible = "fixed-clock";
#clock-cells = <0>;
clock-frequency = <100000000>;
+ u-boot,dm-pre-reloc;
};
clk125: clk125 {
compatible = "fixed-clock";
#clock-cells = <0>;
clock-frequency = <200000000>;
+ u-boot,dm-pre-reloc;
};
clk250: clk250 {
clock-accuracy = <100>;
};
- dpdma_clk: dpdma-clk {
+ dpdma_clk: dpdma_clk {
compatible = "fixed-clock";
#clock-cells = <0x0>;
clock-frequency = <533000000>;
};
- drm_clock: drm-clock {
+ drm_clock: drm_clock {
compatible = "fixed-clock";
#clock-cells = <0x0>;
clock-frequency = <262750000>;
clocks = <&clk600>, <&clk100>;
};
+&nand0 {
+ clocks = <&clk100 &clk100>;
+};
+
&gem0 {
clocks = <&clk125>, <&clk125>, <&clk125>;
};
clocks = <&clk100>;
};
+&perf_monitor_ocm {
+ clocks = <&clk100>;
+};
+
+&perf_monitor_ddr {
+ clocks = <&clk100>;
+};
+
+&perf_monitor_cci {
+ clocks = <&clk100>;
+};
+
+&perf_monitor_lpd {
+ clocks = <&clk100>;
+};
+
+&qspi {
+ clocks = <&clk300 &clk300>;
+};
+
&sata {
clocks = <&clk250>;
};
};
&watchdog0 {
+ clocks = <&clk100>;
+};
+
+&lpd_watchdog {
clocks = <&clk250>;
};
+
+&zynqmp_dpsub {
+ clocks = <&dp_aclk>, <&dp_aud_clk>, <&drm_clock>;
+};
+
+&xlnx_dpdma {
+ clocks = <&dpdma_clk>;
+};
+
+&zynqmp_dp_snd_codec0 {
+ clocks = <&dp_aud_clk>;
+};
/dts-v1/;
#include "zynqmp.dtsi"
-#include "zynqmp-clk.dtsi"
+#include "zynqmp-clk-ccf.dtsi"
+#include <dt-bindings/phy/phy.h>
/ {
model = "ZynqMP ZC1232 RevA";
aliases {
serial0 = &uart0;
serial1 = &dcc;
+ spi0 = &qspi;
};
chosen {
status = "okay";
};
+&qspi {
+ status = "okay";
+ flash@0 {
+ compatible = "m25p80", "spi-flash"; /* 32MB FIXME */
+ #address-cells = <1>;
+ #size-cells = <1>;
+ reg = <0x0>;
+ spi-tx-bus-width = <1>;
+ spi-rx-bus-width = <4>;
+ spi-max-frequency = <108000000>; /* Based on DC1 spec */
+ partition@qspi-fsbl-uboot { /* for testing purpose */
+ label = "qspi-fsbl-uboot";
+ reg = <0x0 0x100000>;
+ };
+ partition@qspi-linux { /* for testing purpose */
+ label = "qspi-linux";
+ reg = <0x100000 0x500000>;
+ };
+ partition@qspi-device-tree { /* for testing purpose */
+ label = "qspi-device-tree";
+ reg = <0x600000 0x20000>;
+ };
+ partition@qspi-rootfs { /* for testing purpose */
+ label = "qspi-rootfs";
+ reg = <0x620000 0x5E0000>;
+ };
+ };
+};
+
&sata {
status = "okay";
/* SATA OOB timing settings */
ceva,p1-comwake-params = /bits/ 8 <0x06 0x14 0x08 0x0E>;
ceva,p1-burst-params = /bits/ 8 <0x13 0x08 0x4A 0x06>;
ceva,p1-retry-params = /bits/ 16 <0x96A4 0x3FFC>;
+ phy-names = "sata-phy";
+ phys = <&lane0 PHY_TYPE_SATA 0 0 125000000>, <&lane1 PHY_TYPE_SATA 1 1 125000000>;
};
&uart0 {
/dts-v1/;
#include "zynqmp.dtsi"
-#include "zynqmp-clk.dtsi"
+#include "zynqmp-clk-ccf.dtsi"
/ {
model = "ZynqMP ZC1254 RevA";
aliases {
serial0 = &uart0;
serial1 = &dcc;
+ spi0 = &qspi;
};
chosen {
status = "okay";
};
+&qspi {
+ status = "okay";
+ flash@0 {
+ compatible = "m25p80", "spi-flash"; /* 32MB */
+ #address-cells = <1>;
+ #size-cells = <1>;
+ reg = <0x0>;
+ spi-tx-bus-width = <1>;
+ spi-rx-bus-width = <4>; /* FIXME also DUAL configuration possible */
+ spi-max-frequency = <108000000>; /* Based on DC1 spec */
+ partition@qspi-fsbl-uboot { /* for testing purpose */
+ label = "qspi-fsbl-uboot";
+ reg = <0x0 0x100000>;
+ };
+ partition@qspi-linux { /* for testing purpose */
+ label = "qspi-linux";
+ reg = <0x100000 0x500000>;
+ };
+ partition@qspi-device-tree { /* for testing purpose */
+ label = "qspi-device-tree";
+ reg = <0x600000 0x20000>;
+ };
+ partition@qspi-rootfs { /* for testing purpose */
+ label = "qspi-rootfs";
+ reg = <0x620000 0x5E0000>;
+ };
+ };
+};
+
&uart0 {
status = "okay";
};
/dts-v1/;
#include "zynqmp.dtsi"
-#include "zynqmp-clk.dtsi"
+#include "zynqmp-clk-ccf.dtsi"
/ {
model = "ZynqMP ZC1275 RevA";
aliases {
serial0 = &uart0;
serial1 = &dcc;
+ spi0 = &qspi;
};
chosen {
status = "okay";
};
+&qspi {
+ status = "okay";
+ flash@0 {
+ compatible = "m25p80", "spi-flash"; /* 32MB */
+ #address-cells = <1>;
+ #size-cells = <1>;
+ reg = <0x0>;
+ spi-tx-bus-width = <1>;
+ spi-rx-bus-width = <4>; /* FIXME also DUAL configuration possible */
+ spi-max-frequency = <108000000>; /* Based on DC1 spec */
+ partition@qspi-fsbl-uboot { /* for testing purpose */
+ label = "qspi-fsbl-uboot";
+ reg = <0x0 0x100000>;
+ };
+ partition@qspi-linux { /* for testing purpose */
+ label = "qspi-linux";
+ reg = <0x100000 0x500000>;
+ };
+ partition@qspi-device-tree { /* for testing purpose */
+ label = "qspi-device-tree";
+ reg = <0x600000 0x20000>;
+ };
+ partition@qspi-rootfs { /* for testing purpose */
+ label = "qspi-rootfs";
+ reg = <0x620000 0x5E0000>;
+ };
+ };
+};
+
&uart0 {
status = "okay";
};
--- /dev/null
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * dts file for Xilinx ZynqMP ZC1275 RevB
+ *
+ * (C) Copyright 2018, Xilinx, Inc.
+ *
+ * Michal Simek <michal.simek@xilinx.com>
+ * Siva Durga Prasad Paladugu <sivadur@xilinx.com>
+ */
+
+/dts-v1/;
+
+#include "zynqmp.dtsi"
+#include "zynqmp-clk-ccf.dtsi"
+
+/ {
+ model = "ZynqMP ZC1275 RevB";
+ compatible = "xlnx,zynqmp-zc1275-revB", "xlnx,zynqmp-zc1275", "xlnx,zynqmp";
+
+ aliases {
+ serial0 = &uart0;
+ serial1 = &dcc;
+ spi0 = &qspi;
+ mmc0 = &sdhci1;
+ ethernet0 = &gem1;
+ };
+
+ chosen {
+ bootargs = "earlycon";
+ stdout-path = "serial0:115200n8";
+ };
+
+ memory@0 {
+ device_type = "memory";
+ reg = <0x0 0x0 0x0 0x80000000>;
+ };
+};
+
+&dcc {
+ status = "okay";
+};
+
+&gem1 {
+ mdio {
+ phy1: ethernet-phy@1 {
+ reg = <1>; /* KSZ9031RNXIC on AES-FMC-NETW1-G */
+ rxc-skew-ps = <1800>; /* Skew control of RX_CLK pad output */
+ txc-skew-ps = <1800>; /* Skew control of GTX_CLK pad input */
+ txen-skew-ps = <900>; /* Skew control of TX_CTL pad input */
+ rxdv-skew-ps = <0>; /* Skew control of RX_CTL pad output */
+ rxd0-skew-ps = <0>; /* Skew control of RXD0 pad output */
+ rxd1-skew-ps = <0>; /* Skew control of RXD1 pad output */
+ rxd2-skew-ps = <0>; /* Skew control of RXD2 pad output */
+ rxd3-skew-ps = <0>; /* Skew control of RXD3 pad output */
+ txd0-skew-ps = <900>; /* Skew control of TXD0 pad input */
+ txd1-skew-ps = <900>; /* Skew control of TXD1 pad input */
+ txd2-skew-ps = <900>; /* Skew control of TXD2 pad input */
+ txd3-skew-ps = <900>; /* Skew control of TXD3 pad input */
+ };
+ };
+};
+
+&qspi {
+ status = "okay";
+ flash@0 {
+ compatible = "m25p80", "spi-flash"; /* 32MB */
+ #address-cells = <1>;
+ #size-cells = <1>;
+ reg = <0x0>;
+ spi-tx-bus-width = <1>;
+ spi-rx-bus-width = <1>;
+ spi-max-frequency = <108000000>; /* Based on DC1 spec */
+ partition@qspi-fsbl-uboot { /* for testing purpose */
+ label = "qspi-fsbl-uboot";
+ reg = <0x0 0x100000>;
+ };
+ partition@qspi-linux { /* for testing purpose */
+ label = "qspi-linux";
+ reg = <0x100000 0x500000>;
+ };
+ partition@qspi-device-tree { /* for testing purpose */
+ label = "qspi-device-tree";
+ reg = <0x600000 0x20000>;
+ };
+ partition@qspi-rootfs { /* for testing purpose */
+ label = "qspi-rootfs";
+ reg = <0x620000 0x5E0000>;
+ };
+ };
+};
+
+&uart0 {
+ status = "okay";
+};
+
+&sdhci1 {
+ status = "okay";
+ no-1-8-v;
+ xlnx,mio_bank = <1>;
+};
--- /dev/null
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * dts file for Xilinx ZynqMP ZC1275 RevB
+ *
+ * (C) Copyright 2018 - 2019, Xilinx, Inc.
+ *
+ * Michal Simek <michal.simek@xilinx.com>
+ * Siva Durga Prasad Paladugu <sivadur@xilinx.com>
+ */
+
+/dts-v1/;
+
+#include "zynqmp.dtsi"
+#include "zynqmp-clk-ccf.dtsi"
+
+/ {
+ model = "ZynqMP ZC1285 RevA";
+ compatible = "xlnx,zynqmp-zc1285-revA", "xlnx,zynqmp-zc1285", "xlnx,zynqmp";
+
+ aliases {
+ serial0 = &uart0;
+ serial1 = &dcc;
+ spi0 = &qspi;
+ mmc0 = &sdhci1;
+ ethernet0 = &gem1; /* EMIO */
+ ethernet1 = &gem3; /* PS ethernet */
+ i2c = &i2c0; /* EMIO */
+ };
+
+ chosen {
+ bootargs = "earlycon";
+ stdout-path = "serial0:115200n8";
+ };
+
+ memory@0 {
+ device_type = "memory";
+ reg = <0x0 0x0 0x0 0x80000000>;
+ };
+};
+
+&dcc {
+ status = "okay";
+};
+
+&i2c0 {
+ status = "okay";
+ clock-frequency = <400000>;
+
+ i2c-mux@75 {
+ compatible = "nxp,pca9548"; /* u22 */
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x75>;
+
+ i2c@0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0>;
+ /* PMBUS */
+ max20751@74 { /* u23 */
+ compatible = "maxim,max20751";
+ reg = <0x74>;
+ };
+ max20751@70 { /* u89 */
+ compatible = "maxim,max20751";
+ reg = <0x70>;
+ };
+ max15301@a { /* u28 */
+ compatible = "maxim,max15301";
+ reg = <0xa>;
+ };
+ max15303@b { /* u48 */
+ compatible = "maxim,max15303";
+ reg = <0xb>;
+ };
+ max15303@d { /* u27 */
+ compatible = "maxim,max15303";
+ reg = <0xd>;
+ };
+ max15303@e { /* u11 */
+ compatible = "maxim,max15303";
+ reg = <0xe>;
+ };
+ max15303@f { /* u96 */
+ compatible = "maxim,max15303";
+ reg = <0xf>;
+ };
+ max15303@11 { /* u47 */
+ compatible = "maxim,max15303";
+ reg = <0x11>;
+ };
+ max15303@12 { /* u24 */
+ compatible = "maxim,max15303";
+ reg = <0x12>;
+ };
+ max15301@13 { /* u29 */
+ compatible = "maxim,max15301";
+ reg = <0x13>;
+ };
+ max15303@14 { /* u51 */
+ compatible = "maxim,max15303";
+ reg = <0x14>;
+ };
+ max15303@15 { /* u30 */
+ compatible = "maxim,max15303";
+ reg = <0x15>;
+ };
+ max15303@16 { /* u102 */
+ compatible = "maxim,max15303";
+ reg = <0x16>;
+ };
+ max15301@17 { /* u50 */
+ compatible = "maxim,max15301";
+ reg = <0x17>;
+ };
+ max15301@18 { /* u31 */
+ compatible = "maxim,max15301";
+ reg = <0x18>;
+ };
+ };
+ i2c@1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <1>;
+ /* CM_I2C */
+ };
+ i2c@2 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <2>;
+ /* SYS_EEPROM */
+ eeprom: eeprom@54 { /* u101 */
+ compatible = "atmel,24c32"; /* 24LC32A */
+ reg = <0x54>;
+ };
+ };
+ i2c@3 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <3>;
+ /* FMC1 */
+ };
+ i2c@4 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <4>;
+ /* FMC2 */
+ };
+ i2c@5 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <5>;
+ /* ANALOG_PMBUS */
+ ina226@40 { /* u60 */
+ compatible = "ti,ina226";
+ reg = <0x40>;
+ shunt-resistor = <1000>;
+ };
+ ina226@41 { /* u61 */
+ compatible = "ti,ina226";
+ reg = <0x41>;
+ shunt-resistor = <1000>;
+ };
+ ina226@42 { /* u63 */
+ compatible = "ti,ina226";
+ reg = <0x42>;
+ shunt-resistor = <1000>;
+ };
+ ina226@43 { /* u65 */
+ compatible = "ti,ina226";
+ reg = <0x43>;
+ shunt-resistor = <1000>;
+ };
+ ina226@44 { /* u64 */
+ compatible = "ti,ina226";
+ reg = <0x44>;
+ shunt-resistor = <1000>;
+ };
+ };
+ i2c@6 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <6>;
+ /* ANALOG_CM_I2C */
+ };
+ i2c@7 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <7>;
+ /* FMC3 */
+ };
+ };
+};
+
+&gem1 {
+ mdio {
+ phy1: ethernet-phy@1 {
+ reg = <1>; /* KSZ9031RNXIC on AES-FMC-NETW1-G */
+ rxc-skew-ps = <1800>; /* Skew control of RX_CLK pad output */
+ txc-skew-ps = <1800>; /* Skew control of GTX_CLK pad input */
+ txen-skew-ps = <900>; /* Skew control of TX_CTL pad input */
+ rxdv-skew-ps = <0>; /* Skew control of RX_CTL pad output */
+ rxd0-skew-ps = <0>; /* Skew control of RXD0 pad output */
+ rxd1-skew-ps = <0>; /* Skew control of RXD1 pad output */
+ rxd2-skew-ps = <0>; /* Skew control of RXD2 pad output */
+ rxd3-skew-ps = <0>; /* Skew control of RXD3 pad output */
+ txd0-skew-ps = <900>; /* Skew control of TXD0 pad input */
+ txd1-skew-ps = <900>; /* Skew control of TXD1 pad input */
+ txd2-skew-ps = <900>; /* Skew control of TXD2 pad input */
+ txd3-skew-ps = <900>; /* Skew control of TXD3 pad input */
+ };
+ };
+};
+
+&gem3 {
+ status = "okay";
+ phy-mode = "rgmii";
+ phy-handle = <&phy2>;
+ phy2: ethernet-phy@1 {
+ reg = <1>; /* KSZ9031RNXIC */
+ };
+};
+
+&qspi {
+ status = "okay";
+ flash@0 {
+ compatible = "m25p80", "spi-flash"; /* 32MB */
+ #address-cells = <1>;
+ #size-cells = <1>;
+ reg = <0x0>;
+ spi-tx-bus-width = <1>;
+ spi-rx-bus-width = <1>;
+ spi-max-frequency = <108000000>; /* Based on DC1 spec */
+ };
+};
+
+&uart0 {
+ status = "okay";
+};
+
+&sdhci1 {
+ status = "okay";
+ no-1-8-v;
+ xlnx,mio_bank = <1>;
+};
/dts-v1/;
#include "zynqmp.dtsi"
-#include "zynqmp-clk.dtsi"
+#include "zynqmp-clk-ccf.dtsi"
+#include <dt-bindings/phy/phy.h>
#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/pinctrl/pinctrl-zynqmp.h>
/ {
model = "ZynqMP zc1751-xm015-dc1 RevA";
aliases {
ethernet0 = &gem3;
+ gpio0 = &gpio;
i2c0 = &i2c1;
mmc0 = &sdhci0;
mmc1 = &sdhci1;
rtc0 = &rtc;
serial0 = &uart0;
+ spi0 = &qspi;
+ usb0 = &usb0;
};
chosen {
status = "okay";
phy-handle = <&phy0>;
phy-mode = "rgmii-id";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_gem3_default>;
phy0: phy@0 {
reg = <0>;
};
&gpio {
status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_gpio_default>;
};
+&gpu {
+ status = "okay";
+};
&i2c1 {
status = "okay";
clock-frequency = <400000>;
+ pinctrl-names = "default", "gpio";
+ pinctrl-0 = <&pinctrl_i2c1_default>;
+ pinctrl-1 = <&pinctrl_i2c1_gpio>;
+ scl-gpios = <&gpio 36 GPIO_ACTIVE_HIGH>;
+ sda-gpios = <&gpio 37 GPIO_ACTIVE_HIGH>;
eeprom: eeprom@55 {
compatible = "atmel,24c64"; /* 24AA64 */
};
};
+&pinctrl0 {
+ status = "okay";
+ pinctrl_i2c1_default: i2c1-default {
+ mux {
+ groups = "i2c1_9_grp";
+ function = "i2c1";
+ };
+
+ conf {
+ groups = "i2c1_9_grp";
+ bias-pull-up;
+ slew-rate = <SLEW_RATE_SLOW>;
+ io-standard = <IO_STANDARD_LVCMOS18>;
+ };
+ };
+
+ pinctrl_i2c1_gpio: i2c1-gpio {
+ mux {
+ groups = "gpio0_36_grp", "gpio0_37_grp";
+ function = "gpio0";
+ };
+
+ conf {
+ groups = "gpio0_36_grp", "gpio0_37_grp";
+ slew-rate = <SLEW_RATE_SLOW>;
+ io-standard = <IO_STANDARD_LVCMOS18>;
+ };
+ };
+
+ pinctrl_uart0_default: uart0-default {
+ mux {
+ groups = "uart0_8_grp";
+ function = "uart0";
+ };
+
+ conf {
+ groups = "uart0_8_grp";
+ slew-rate = <SLEW_RATE_SLOW>;
+ io-standard = <IO_STANDARD_LVCMOS18>;
+ };
+
+ conf-rx {
+ pins = "MIO34";
+ bias-high-impedance;
+ };
+
+ conf-tx {
+ pins = "MIO35";
+ bias-disable;
+ };
+ };
+
+ pinctrl_usb0_default: usb0-default {
+ mux {
+ groups = "usb0_0_grp";
+ function = "usb0";
+ };
+
+ conf {
+ groups = "usb0_0_grp";
+ slew-rate = <SLEW_RATE_SLOW>;
+ io-standard = <IO_STANDARD_LVCMOS18>;
+ };
+
+ conf-rx {
+ pins = "MIO52", "MIO53", "MIO55";
+ bias-high-impedance;
+ };
+
+ conf-tx {
+ pins = "MIO54", "MIO56", "MIO57", "MIO58", "MIO59",
+ "MIO60", "MIO61", "MIO62", "MIO63";
+ bias-disable;
+ };
+ };
+
+ pinctrl_gem3_default: gem3-default {
+ mux {
+ function = "ethernet3";
+ groups = "ethernet3_0_grp";
+ };
+
+ conf {
+ groups = "ethernet3_0_grp";
+ slew-rate = <SLEW_RATE_SLOW>;
+ io-standard = <IO_STANDARD_LVCMOS18>;
+ };
+
+ conf-rx {
+ pins = "MIO70", "MIO71", "MIO72", "MIO73", "MIO74",
+ "MIO75";
+ bias-high-impedance;
+ low-power-disable;
+ };
+
+ conf-tx {
+ pins = "MIO64", "MIO65", "MIO66", "MIO67", "MIO68",
+ "MIO69";
+ bias-disable;
+ low-power-enable;
+ };
+
+ mux-mdio {
+ function = "mdio3";
+ groups = "mdio3_0_grp";
+ };
+
+ conf-mdio {
+ groups = "mdio3_0_grp";
+ slew-rate = <SLEW_RATE_SLOW>;
+ io-standard = <IO_STANDARD_LVCMOS18>;
+ bias-disable;
+ };
+ };
+
+ pinctrl_sdhci0_default: sdhci0-default {
+ mux {
+ groups = "sdio0_0_grp";
+ function = "sdio0";
+ };
+
+ conf {
+ groups = "sdio0_0_grp";
+ slew-rate = <SLEW_RATE_SLOW>;
+ io-standard = <IO_STANDARD_LVCMOS18>;
+ bias-disable;
+ };
+
+ mux-cd {
+ groups = "sdio0_cd_0_grp";
+ function = "sdio0_cd";
+ };
+
+ conf-cd {
+ groups = "sdio0_cd_0_grp";
+ bias-high-impedance;
+ bias-pull-up;
+ slew-rate = <SLEW_RATE_SLOW>;
+ io-standard = <IO_STANDARD_LVCMOS18>;
+ };
+
+ mux-wp {
+ groups = "sdio0_wp_0_grp";
+ function = "sdio0_wp";
+ };
+
+ conf-wp {
+ groups = "sdio0_wp_0_grp";
+ bias-high-impedance;
+ bias-pull-up;
+ slew-rate = <SLEW_RATE_SLOW>;
+ io-standard = <IO_STANDARD_LVCMOS18>;
+ };
+ };
+
+ pinctrl_sdhci1_default: sdhci1-default {
+ mux {
+ groups = "sdio1_0_grp";
+ function = "sdio1";
+ };
+
+ conf {
+ groups = "sdio1_0_grp";
+ slew-rate = <SLEW_RATE_SLOW>;
+ io-standard = <IO_STANDARD_LVCMOS18>;
+ bias-disable;
+ };
+
+ mux-cd {
+ groups = "sdio1_cd_0_grp";
+ function = "sdio1_cd";
+ };
+
+ conf-cd {
+ groups = "sdio1_cd_0_grp";
+ bias-high-impedance;
+ bias-pull-up;
+ slew-rate = <SLEW_RATE_SLOW>;
+ io-standard = <IO_STANDARD_LVCMOS18>;
+ };
+
+ mux-wp {
+ groups = "sdio1_wp_0_grp";
+ function = "sdio1_wp";
+ };
+
+ conf-wp {
+ groups = "sdio1_wp_0_grp";
+ bias-high-impedance;
+ bias-pull-up;
+ slew-rate = <SLEW_RATE_SLOW>;
+ io-standard = <IO_STANDARD_LVCMOS18>;
+ };
+ };
+
+ pinctrl_gpio_default: gpio-default {
+ mux {
+ function = "gpio0";
+ groups = "gpio0_38_grp";
+ };
+
+ conf {
+ groups = "gpio0_38_grp";
+ bias-disable;
+ slew-rate = <SLEW_RATE_SLOW>;
+ io-standard = <IO_STANDARD_LVCMOS18>;
+ };
+ };
+};
+
+&qspi {
+ status = "okay";
+ flash@0 {
+ compatible = "m25p80", "spi-flash"; /* Micron MT25QU512ABB8ESF */
+ #address-cells = <1>;
+ #size-cells = <1>;
+ reg = <0x0>;
+ spi-tx-bus-width = <1>;
+ spi-rx-bus-width = <4>;
+ spi-max-frequency = <108000000>; /* Based on DC1 spec */
+ partition@qspi-fsbl-uboot { /* for testing purpose */
+ label = "qspi-fsbl-uboot";
+ reg = <0x0 0x100000>;
+ };
+ partition@qspi-linux { /* for testing purpose */
+ label = "qspi-linux";
+ reg = <0x100000 0x500000>;
+ };
+ partition@qspi-device-tree { /* for testing purpose */
+ label = "qspi-device-tree";
+ reg = <0x600000 0x20000>;
+ };
+ partition@qspi-rootfs { /* for testing purpose */
+ label = "qspi-rootfs";
+ reg = <0x620000 0x5E0000>;
+ };
+ };
+};
+
&rtc {
status = "okay";
};
ceva,p1-comwake-params = /bits/ 8 <0x06 0x19 0x08 0x0E>;
ceva,p1-burst-params = /bits/ 8 <0x13 0x08 0x4A 0x06>;
ceva,p1-retry-params = /bits/ 16 <0x96A4 0x3FFC>;
+ phy-names = "sata-phy";
+ phys = <&lane3 PHY_TYPE_SATA 1 3 150000000>;
};
/* eMMC */
&sdhci0 {
status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_sdhci0_default>;
bus-width = <8>;
+ xlnx,mio_bank = <0>;
};
/* SD1 with level shifter */
&sdhci1 {
status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_sdhci1_default>;
+ xlnx,mio_bank = <1>;
+};
+
+&serdes {
+ status = "okay";
};
&uart0 {
status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart0_default>;
};
/* ULPI SMSC USB3320 */
&usb0 {
status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usb0_default>;
+};
+
+&dwc3_0 {
+ status = "okay";
+ dr_mode = "host";
+ snps,usb3_lpm_capable;
+ phy-names = "usb3-phy";
+ phys = <&lane2 PHY_TYPE_USB3 0 2 26000000>;
+};
+
+&zynqmp_dpsub {
+ status = "okay";
+ phy-names = "dp-phy0", "dp-phy1";
+ phys = <&lane1 PHY_TYPE_DP 0 0 27000000>,
+ <&lane0 PHY_TYPE_DP 1 1 27000000>;
+};
+
+&zynqmp_dp_snd_pcm0 {
+ status = "okay";
+};
+
+&zynqmp_dp_snd_pcm1 {
+ status = "okay";
+};
+
+&zynqmp_dp_snd_card0 {
+ status = "okay";
+};
+
+&zynqmp_dp_snd_codec0 {
+ status = "okay";
+};
+
+&xlnx_dpdma {
+ status = "okay";
};
/dts-v1/;
#include "zynqmp.dtsi"
-#include "zynqmp-clk.dtsi"
+#include "zynqmp-clk-ccf.dtsi"
#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/pinctrl/pinctrl-zynqmp.h>
/ {
model = "ZynqMP zc1751-xm016-dc2 RevA";
can0 = &can0;
can1 = &can1;
ethernet0 = &gem2;
+ gpio0 = &gpio;
i2c0 = &i2c0;
rtc0 = &rtc;
serial0 = &uart0;
serial1 = &uart1;
spi0 = &spi0;
spi1 = &spi1;
+ usb0 = &usb1;
};
chosen {
&can0 {
status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_can0_default>;
};
&can1 {
status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_can1_default>;
};
&fpd_dma_chan1 {
status = "okay";
phy-handle = <&phy0>;
phy-mode = "rgmii-id";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_gem2_default>;
phy0: phy@5 {
reg = <5>;
ti,rx-internal-delay = <0x8>;
ti,tx-internal-delay = <0xa>;
ti,fifo-depth = <0x1>;
+ ti,dp83867-rxctrl-strap-quirk;
};
};
&i2c0 {
status = "okay";
clock-frequency = <400000>;
+ pinctrl-names = "default", "gpio";
+ pinctrl-0 = <&pinctrl_i2c0_default>;
+ pinctrl-1 = <&pinctrl_i2c0_gpio>;
+ scl-gpios = <&gpio 6 GPIO_ACTIVE_HIGH>;
+ sda-gpios = <&gpio 7 GPIO_ACTIVE_HIGH>;
tca6416_u26: gpio@20 {
compatible = "ti,tca6416";
};
};
+&nand0 {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_nand0_default>;
+ arasan,has-mdma;
+
+ nand@0 {
+ reg = <0x0>;
+ #address-cells = <0x2>;
+ #size-cells = <0x1>;
+
+ partition@0 { /* for testing purpose */
+ label = "nand-fsbl-uboot";
+ reg = <0x0 0x0 0x400000>;
+ };
+ partition@1 { /* for testing purpose */
+ label = "nand-linux";
+ reg = <0x0 0x400000 0x1400000>;
+ };
+ partition@2 { /* for testing purpose */
+ label = "nand-device-tree";
+ reg = <0x0 0x1800000 0x400000>;
+ };
+ partition@3 { /* for testing purpose */
+ label = "nand-rootfs";
+ reg = <0x0 0x1c00000 0x1400000>;
+ };
+ partition@4 { /* for testing purpose */
+ label = "nand-bitstream";
+ reg = <0x0 0x3000000 0x400000>;
+ };
+ partition@5 { /* for testing purpose */
+ label = "nand-misc";
+ reg = <0x0 0x3400000 0xfcc00000>;
+ };
+ };
+ nand@1 {
+ reg = <0x1>;
+ #address-cells = <0x2>;
+ #size-cells = <0x1>;
+
+ partition@0 { /* for testing purpose */
+ label = "nand1-fsbl-uboot";
+ reg = <0x0 0x0 0x400000>;
+ };
+ partition@1 { /* for testing purpose */
+ label = "nand1-linux";
+ reg = <0x0 0x400000 0x1400000>;
+ };
+ partition@2 { /* for testing purpose */
+ label = "nand1-device-tree";
+ reg = <0x0 0x1800000 0x400000>;
+ };
+ partition@3 { /* for testing purpose */
+ label = "nand1-rootfs";
+ reg = <0x0 0x1c00000 0x1400000>;
+ };
+ partition@4 { /* for testing purpose */
+ label = "nand1-bitstream";
+ reg = <0x0 0x3000000 0x400000>;
+ };
+ partition@5 { /* for testing purpose */
+ label = "nand1-misc";
+ reg = <0x0 0x3400000 0xfcc00000>;
+ };
+ };
+};
+
+&pinctrl0 {
+ status = "okay";
+ pinctrl_can0_default: can0-default {
+ mux {
+ function = "can0";
+ groups = "can0_9_grp";
+ };
+
+ conf {
+ groups = "can0_9_grp";
+ slew-rate = <SLEW_RATE_SLOW>;
+ io-standard = <IO_STANDARD_LVCMOS18>;
+ };
+
+ conf-rx {
+ pins = "MIO38";
+ bias-high-impedance;
+ };
+
+ conf-tx {
+ pins = "MIO39";
+ bias-disable;
+ };
+ };
+
+ pinctrl_can1_default: can1-default {
+ mux {
+ function = "can1";
+ groups = "can1_8_grp";
+ };
+
+ conf {
+ groups = "can1_8_grp";
+ slew-rate = <SLEW_RATE_SLOW>;
+ io-standard = <IO_STANDARD_LVCMOS18>;
+ };
+
+ conf-rx {
+ pins = "MIO33";
+ bias-high-impedance;
+ };
+
+ conf-tx {
+ pins = "MIO32";
+ bias-disable;
+ };
+ };
+
+ pinctrl_i2c0_default: i2c0-default {
+ mux {
+ groups = "i2c0_1_grp";
+ function = "i2c0";
+ };
+
+ conf {
+ groups = "i2c0_1_grp";
+ bias-pull-up;
+ slew-rate = <SLEW_RATE_SLOW>;
+ io-standard = <IO_STANDARD_LVCMOS18>;
+ };
+ };
+
+ pinctrl_i2c0_gpio: i2c0-gpio {
+ mux {
+ groups = "gpio0_6_grp", "gpio0_7_grp";
+ function = "gpio0";
+ };
+
+ conf {
+ groups = "gpio0_6_grp", "gpio0_7_grp";
+ slew-rate = <SLEW_RATE_SLOW>;
+ io-standard = <IO_STANDARD_LVCMOS18>;
+ };
+ };
+
+ pinctrl_uart0_default: uart0-default {
+ mux {
+ groups = "uart0_10_grp";
+ function = "uart0";
+ };
+
+ conf {
+ groups = "uart0_10_grp";
+ slew-rate = <SLEW_RATE_SLOW>;
+ io-standard = <IO_STANDARD_LVCMOS18>;
+ };
+
+ conf-rx {
+ pins = "MIO42";
+ bias-high-impedance;
+ };
+
+ conf-tx {
+ pins = "MIO43";
+ bias-disable;
+ };
+ };
+
+ pinctrl_uart1_default: uart1-default {
+ mux {
+ groups = "uart1_10_grp";
+ function = "uart1";
+ };
+
+ conf {
+ groups = "uart1_10_grp";
+ slew-rate = <SLEW_RATE_SLOW>;
+ io-standard = <IO_STANDARD_LVCMOS18>;
+ };
+
+ conf-rx {
+ pins = "MIO41";
+ bias-high-impedance;
+ };
+
+ conf-tx {
+ pins = "MIO40";
+ bias-disable;
+ };
+ };
+
+ pinctrl_usb1_default: usb1-default {
+ mux {
+ groups = "usb1_0_grp";
+ function = "usb1";
+ };
+
+ conf {
+ groups = "usb1_0_grp";
+ slew-rate = <SLEW_RATE_SLOW>;
+ io-standard = <IO_STANDARD_LVCMOS18>;
+ };
+
+ conf-rx {
+ pins = "MIO64", "MIO65", "MIO67";
+ bias-high-impedance;
+ };
+
+ conf-tx {
+ pins = "MIO66", "MIO68", "MIO69", "MIO70", "MIO71",
+ "MIO72", "MIO73", "MIO74", "MIO75";
+ bias-disable;
+ };
+ };
+
+ pinctrl_gem2_default: gem2-default {
+ mux {
+ function = "ethernet2";
+ groups = "ethernet2_0_grp";
+ };
+
+ conf {
+ groups = "ethernet2_0_grp";
+ slew-rate = <SLEW_RATE_SLOW>;
+ io-standard = <IO_STANDARD_LVCMOS18>;
+ };
+
+ conf-rx {
+ pins = "MIO58", "MIO59", "MIO60", "MIO61", "MIO62",
+ "MIO63";
+ bias-high-impedance;
+ low-power-disable;
+ };
+
+ conf-tx {
+ pins = "MIO52", "MIO53", "MIO54", "MIO55", "MIO56",
+ "MIO57";
+ bias-disable;
+ low-power-enable;
+ };
+
+ mux-mdio {
+ function = "mdio2";
+ groups = "mdio2_0_grp";
+ };
+
+ conf-mdio {
+ groups = "mdio2_0_grp";
+ slew-rate = <SLEW_RATE_SLOW>;
+ io-standard = <IO_STANDARD_LVCMOS18>;
+ bias-disable;
+ };
+ };
+
+ pinctrl_nand0_default: nand0-default {
+ mux {
+ groups = "nand0_0_grp";
+ function = "nand0";
+ };
+
+ conf {
+ groups = "nand0_0_grp";
+ bias-pull-up;
+ };
+
+ mux-ce {
+ groups = "nand0_ce_0_grp";
+ function = "nand0_ce";
+ };
+
+ conf-ce {
+ groups = "nand0_ce_0_grp";
+ bias-pull-up;
+ };
+
+ mux-rb {
+ groups = "nand0_rb_0_grp";
+ function = "nand0_rb";
+ };
+
+ conf-rb {
+ groups = "nand0_rb_0_grp";
+ bias-pull-up;
+ };
+
+ mux-dqs {
+ groups = "nand0_dqs_0_grp";
+ function = "nand0_dqs";
+ };
+
+ conf-dqs {
+ groups = "nand0_dqs_0_grp";
+ bias-pull-up;
+ };
+ };
+
+ pinctrl_spi0_default: spi0-default {
+ mux {
+ groups = "spi0_0_grp";
+ function = "spi0";
+ };
+
+ conf {
+ groups = "spi0_0_grp";
+ bias-disable;
+ slew-rate = <SLEW_RATE_SLOW>;
+ io-standard = <IO_STANDARD_LVCMOS18>;
+ };
+
+ mux-cs {
+ groups = "spi0_ss_0_grp", "spi0_ss_1_grp",
+ "spi0_ss_2_grp";
+ function = "spi0_ss";
+ };
+
+ conf-cs {
+ groups = "spi0_ss_0_grp", "spi0_ss_1_grp",
+ "spi0_ss_2_grp";
+ bias-disable;
+ };
+ };
+
+ pinctrl_spi1_default: spi1-default {
+ mux {
+ groups = "spi1_3_grp";
+ function = "spi1";
+ };
+
+ conf {
+ groups = "spi1_3_grp";
+ bias-disable;
+ slew-rate = <SLEW_RATE_SLOW>;
+ io-standard = <IO_STANDARD_LVCMOS18>;
+ };
+
+ mux-cs {
+ groups = "spi1_ss_9_grp", "spi1_ss_10_grp",
+ "spi1_ss_11_grp";
+ function = "spi1_ss";
+ };
+
+ conf-cs {
+ groups = "spi1_ss_9_grp", "spi1_ss_10_grp",
+ "spi1_ss_11_grp";
+ bias-disable;
+ };
+ };
+};
+
&rtc {
status = "okay";
};
&spi0 {
status = "okay";
num-cs = <1>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_spi0_default>;
- spi0_flash0: flash0@0 {
+ spi0_flash0: flash@0 {
#address-cells = <1>;
#size-cells = <1>;
compatible = "sst,sst25wf080", "jedec,spi-nor";
&spi1 {
status = "okay";
num-cs = <1>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_spi1_default>;
- spi1_flash0: flash0@0 {
+ spi1_flash0: flash@0 {
#address-cells = <1>;
#size-cells = <1>;
compatible = "atmel,at45db041e", "atmel,at45", "atmel,dataflash";
/* ULPI SMSC USB3320 */
&usb1 {
status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usb1_default>;
+};
+
+&dwc3_1 {
+ status = "okay";
+ dr_mode = "host";
};
&uart0 {
status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart0_default>;
};
&uart1 {
status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart1_default>;
};
/dts-v1/;
#include "zynqmp.dtsi"
-#include "zynqmp-clk.dtsi"
+#include "zynqmp-clk-ccf.dtsi"
/ {
model = "ZynqMP zc1751-xm017-dc3 RevA";
aliases {
ethernet0 = &gem0;
+ gpio0 = &gpio;
i2c0 = &i2c0;
i2c1 = &i2c1;
mmc0 = &sdhci1;
rtc0 = &rtc;
serial0 = &uart0;
serial1 = &uart1;
+ usb0 = &usb0;
+ usb1 = &usb1;
};
chosen {
clock-frequency = <400000>;
};
+/* MT29F64G08AECDBJ4-6 */
+&nand0 {
+ status = "okay";
+ arasan,has-mdma;
+ num-cs = <2>;
+
+ partition@0 { /* for testing purpose */
+ label = "nand-fsbl-uboot";
+ reg = <0x0 0x0 0x400000>;
+ };
+ partition@1 { /* for testing purpose */
+ label = "nand-linux";
+ reg = <0x0 0x400000 0x1400000>;
+ };
+ partition@2 { /* for testing purpose */
+ label = "nand-device-tree";
+ reg = <0x0 0x1800000 0x400000>;
+ };
+ partition@3 { /* for testing purpose */
+ label = "nand-rootfs";
+ reg = <0x0 0x1C00000 0x1400000>;
+ };
+ partition@4 { /* for testing purpose */
+ label = "nand-bitstream";
+ reg = <0x0 0x3000000 0x400000>;
+ };
+ partition@5 { /* for testing purpose */
+ label = "nand-misc";
+ reg = <0x0 0x3400000 0xFCC00000>;
+ };
+
+ partition@6 { /* for testing purpose */
+ label = "nand1-fsbl-uboot";
+ reg = <0x1 0x0 0x400000>;
+ };
+ partition@7 { /* for testing purpose */
+ label = "nand1-linux";
+ reg = <0x1 0x400000 0x1400000>;
+ };
+ partition@8 { /* for testing purpose */
+ label = "nand1-device-tree";
+ reg = <0x1 0x1800000 0x400000>;
+ };
+ partition@9 { /* for testing purpose */
+ label = "nand1-rootfs";
+ reg = <0x1 0x1C00000 0x1400000>;
+ };
+ partition@10 { /* for testing purpose */
+ label = "nand1-bitstream";
+ reg = <0x1 0x3000000 0x400000>;
+ };
+ partition@11 { /* for testing purpose */
+ label = "nand1-misc";
+ reg = <0x1 0x3400000 0xFCC00000>;
+ };
+};
+
&rtc {
status = "okay";
};
/dts-v1/;
#include "zynqmp.dtsi"
-#include "zynqmp-clk.dtsi"
+#include "zynqmp-clk-ccf.dtsi"
/ {
model = "ZynqMP zc1751-xm018-dc4";
compatible = "xlnx,zynqmp-zc1751", "xlnx,zynqmp";
aliases {
+ can0 = &can0;
+ can1 = &can1;
ethernet0 = &gem0;
ethernet1 = &gem1;
ethernet2 = &gem2;
ethernet3 = &gem3;
+ gpio0 = &gpio;
i2c0 = &i2c0;
i2c1 = &i2c1;
rtc0 = &rtc;
serial0 = &uart0;
serial1 = &uart1;
+ spi0 = &qspi;
};
chosen {
status = "okay";
};
+&zynqmp_dpsub {
+ status = "okay";
+};
+
+&xlnx_dpdma {
+ status = "okay";
+};
+
&gem0 {
status = "okay";
phy-mode = "rgmii-id";
status = "okay";
};
+&gpu {
+ status = "okay";
+};
+
&i2c0 {
clock-frequency = <400000>;
status = "okay";
status = "okay";
};
+&qspi {
+ status = "okay";
+ flash@0 {
+ compatible = "m25p80", "spi-flash"; /* 32MB */
+ #address-cells = <1>;
+ #size-cells = <1>;
+ reg = <0x0>;
+ spi-tx-bus-width = <1>;
+ spi-rx-bus-width = <4>; /* also DUAL configuration possible */
+ spi-max-frequency = <108000000>; /* Based on DC1 spec */
+ partition@qspi-fsbl-uboot { /* for testing purpose */
+ label = "qspi-fsbl-uboot";
+ reg = <0x0 0x100000>;
+ };
+ partition@qspi-linux { /* for testing purpose */
+ label = "qspi-linux";
+ reg = <0x100000 0x500000>;
+ };
+ partition@qspi-device-tree { /* for testing purpose */
+ label = "qspi-device-tree";
+ reg = <0x600000 0x20000>;
+ };
+ partition@qspi-rootfs { /* for testing purpose */
+ label = "qspi-rootfs";
+ reg = <0x620000 0x5E0000>;
+ };
+ };
+};
+
&rtc {
status = "okay";
};
/dts-v1/;
#include "zynqmp.dtsi"
-#include "zynqmp-clk.dtsi"
+#include "zynqmp-clk-ccf.dtsi"
#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/pinctrl/pinctrl-zynqmp.h>
/ {
model = "ZynqMP zc1751-xm019-dc5 RevA";
aliases {
ethernet0 = &gem1;
+ gpio0 = &gpio;
i2c0 = &i2c0;
i2c1 = &i2c1;
mmc0 = &sdhci0;
status = "okay";
phy-handle = <&phy0>;
phy-mode = "rgmii-id";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_gem1_default>;
phy0: phy@0 {
reg = <0>;
};
&i2c0 {
status = "okay";
+ pinctrl-names = "default", "gpio";
+ pinctrl-0 = <&pinctrl_i2c0_default>;
+ pinctrl-1 = <&pinctrl_i2c0_gpio>;
+ scl-gpios = <&gpio 74 GPIO_ACTIVE_HIGH>;
+ sda-gpios = <&gpio 75 GPIO_ACTIVE_HIGH>;
};
&i2c1 {
status = "okay";
+ pinctrl-names = "default", "gpio";
+ pinctrl-0 = <&pinctrl_i2c1_default>;
+ pinctrl-1 = <&pinctrl_i2c1_gpio>;
+ scl-gpios = <&gpio 76 GPIO_ACTIVE_HIGH>;
+ sda-gpios = <&gpio 77 GPIO_ACTIVE_HIGH>;
+
+};
+
+&pinctrl0 {
+ status = "okay";
+ pinctrl_i2c0_default: i2c0-default {
+ mux {
+ groups = "i2c0_18_grp";
+ function = "i2c0";
+ };
+
+ conf {
+ groups = "i2c0_18_grp";
+ bias-pull-up;
+ slew-rate = <SLEW_RATE_SLOW>;
+ io-standard = <IO_STANDARD_LVCMOS18>;
+ };
+ };
+
+ pinctrl_i2c0_gpio: i2c0-gpio {
+ mux {
+ groups = "gpio0_74_grp", "gpio0_75_grp";
+ function = "gpio0";
+ };
+
+ conf {
+ groups = "gpio0_74_grp", "gpio0_75_grp";
+ slew-rate = <SLEW_RATE_SLOW>;
+ io-standard = <IO_STANDARD_LVCMOS18>;
+ };
+ };
+
+ pinctrl_i2c1_default: i2c1-default {
+ mux {
+ groups = "i2c1_19_grp";
+ function = "i2c1";
+ };
+
+ conf {
+ groups = "i2c1_19_grp";
+ bias-pull-up;
+ slew-rate = <SLEW_RATE_SLOW>;
+ io-standard = <IO_STANDARD_LVCMOS18>;
+ };
+ };
+
+ pinctrl_i2c1_gpio: i2c1-gpio {
+ mux {
+ groups = "gpio0_76_grp", "gpio0_77_grp";
+ function = "gpio0";
+ };
+
+ conf {
+ groups = "gpio0_76_grp", "gpio0_77_grp";
+ slew-rate = <SLEW_RATE_SLOW>;
+ io-standard = <IO_STANDARD_LVCMOS18>;
+ };
+ };
+
+ pinctrl_uart0_default: uart0-default {
+ mux {
+ groups = "uart0_17_grp";
+ function = "uart0";
+ };
+
+ conf {
+ groups = "uart0_17_grp";
+ slew-rate = <SLEW_RATE_SLOW>;
+ io-standard = <IO_STANDARD_LVCMOS18>;
+ };
+
+ conf-rx {
+ pins = "MIO70";
+ bias-high-impedance;
+ };
+
+ conf-tx {
+ pins = "MIO71";
+ bias-disable;
+ };
+ };
+
+ pinctrl_uart1_default: uart1-default {
+ mux {
+ groups = "uart1_18_grp";
+ function = "uart1";
+ };
+
+ conf {
+ groups = "uart1_18_grp";
+ slew-rate = <SLEW_RATE_SLOW>;
+ io-standard = <IO_STANDARD_LVCMOS18>;
+ };
+
+ conf-rx {
+ pins = "MIO73";
+ bias-high-impedance;
+ };
+
+ conf-tx {
+ pins = "MIO72";
+ bias-disable;
+ };
+ };
+
+ pinctrl_gem1_default: gem1-default {
+ mux {
+ function = "ethernet1";
+ groups = "ethernet1_0_grp";
+ };
+
+ conf {
+ groups = "ethernet1_0_grp";
+ slew-rate = <SLEW_RATE_SLOW>;
+ io-standard = <IO_STANDARD_LVCMOS18>;
+ };
+
+ conf-rx {
+ pins = "MIO44", "MIO45", "MIO46", "MIO47", "MIO48",
+ "MIO49";
+ bias-high-impedance;
+ low-power-disable;
+ };
+
+ conf-tx {
+ pins = "MIO38", "MIO39", "MIO40", "MIO41", "MIO42",
+ "MIO43";
+ bias-disable;
+ low-power-enable;
+ };
+
+ mux-mdio {
+ function = "mdio1";
+ groups = "mdio1_0_grp";
+ };
+
+ conf-mdio {
+ groups = "mdio1_0_grp";
+ slew-rate = <SLEW_RATE_SLOW>;
+ io-standard = <IO_STANDARD_LVCMOS18>;
+ bias-disable;
+ };
+ };
+
+ pinctrl_sdhci0_default: sdhci0-default {
+ mux {
+ groups = "sdio0_0_grp";
+ function = "sdio0";
+ };
+
+ conf {
+ groups = "sdio0_0_grp";
+ slew-rate = <SLEW_RATE_SLOW>;
+ io-standard = <IO_STANDARD_LVCMOS18>;
+ bias-disable;
+ };
+
+ mux-cd {
+ groups = "sdio0_cd_0_grp";
+ function = "sdio0_cd";
+ };
+
+ conf-cd {
+ groups = "sdio0_cd_0_grp";
+ bias-high-impedance;
+ bias-pull-up;
+ slew-rate = <SLEW_RATE_SLOW>;
+ io-standard = <IO_STANDARD_LVCMOS18>;
+ };
+
+ mux-wp {
+ groups = "sdio0_wp_0_grp";
+ function = "sdio0_wp";
+ };
+
+ conf-wp {
+ groups = "sdio0_wp_0_grp";
+ bias-high-impedance;
+ bias-pull-up;
+ slew-rate = <SLEW_RATE_SLOW>;
+ io-standard = <IO_STANDARD_LVCMOS18>;
+ };
+ };
+
+ pinctrl_watchdog0_default: watchdog0-default {
+ mux-clk {
+ groups = "swdt0_clk_1_grp";
+ function = "swdt0_clk";
+ };
+
+ conf-clk {
+ groups = "swdt0_clk_1_grp";
+ bias-pull-up;
+ };
+
+ mux-rst {
+ groups = "swdt0_rst_1_grp";
+ function = "swdt0_rst";
+ };
+
+ conf-rst {
+ groups = "swdt0_rst_1_grp";
+ bias-disable;
+ slew-rate = <SLEW_RATE_SLOW>;
+ };
+ };
+
+ pinctrl_ttc0_default: ttc0-default {
+ mux-clk {
+ groups = "ttc0_clk_0_grp";
+ function = "ttc0_clk";
+ };
+
+ conf-clk {
+ groups = "ttc0_clk_0_grp";
+ bias-pull-up;
+ };
+
+ mux-wav {
+ groups = "ttc0_wav_0_grp";
+ function = "ttc0_wav";
+ };
+
+ conf-wav {
+ groups = "ttc0_wav_0_grp";
+ bias-disable;
+ slew-rate = <SLEW_RATE_SLOW>;
+ };
+ };
+
+ pinctrl_ttc1_default: ttc1-default {
+ mux-clk {
+ groups = "ttc1_clk_0_grp";
+ function = "ttc1_clk";
+ };
+
+ conf-clk {
+ groups = "ttc1_clk_0_grp";
+ bias-pull-up;
+ };
+
+ mux-wav {
+ groups = "ttc1_wav_0_grp";
+ function = "ttc1_wav";
+ };
+
+ conf-wav {
+ groups = "ttc1_wav_0_grp";
+ bias-disable;
+ slew-rate = <SLEW_RATE_SLOW>;
+ };
+ };
+
+ pinctrl_ttc2_default: ttc2-default {
+ mux-clk {
+ groups = "ttc2_clk_0_grp";
+ function = "ttc2_clk";
+ };
+
+ conf-clk {
+ groups = "ttc2_clk_0_grp";
+ bias-pull-up;
+ };
+
+ mux-wav {
+ groups = "ttc2_wav_0_grp";
+ function = "ttc2_wav";
+ };
+
+ conf-wav {
+ groups = "ttc2_wav_0_grp";
+ bias-disable;
+ slew-rate = <SLEW_RATE_SLOW>;
+ };
+ };
+
+ pinctrl_ttc3_default: ttc3-default {
+ mux-clk {
+ groups = "ttc3_clk_0_grp";
+ function = "ttc3_clk";
+ };
+
+ conf-clk {
+ groups = "ttc3_clk_0_grp";
+ bias-pull-up;
+ };
+
+ mux-wav {
+ groups = "ttc3_wav_0_grp";
+ function = "ttc3_wav";
+ };
+
+ conf-wav {
+ groups = "ttc3_wav_0_grp";
+ bias-disable;
+ slew-rate = <SLEW_RATE_SLOW>;
+ };
+ };
};
&sdhci0 {
status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_sdhci0_default>;
no-1-8-v;
+ xlnx,mio_bank = <0>;
};
&ttc0 {
status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ttc0_default>;
};
&ttc1 {
status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ttc1_default>;
};
&ttc2 {
status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ttc2_default>;
};
&ttc3 {
status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ttc3_default>;
};
&uart0 {
status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart0_default>;
};
&uart1 {
status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart1_default>;
};
&watchdog0 {
status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_watchdog0_default>;
};
/dts-v1/;
#include "zynqmp.dtsi"
-#include "zynqmp-clk.dtsi"
+#include "zynqmp-clk-ccf.dtsi"
#include <dt-bindings/input/input.h>
#include <dt-bindings/interrupt-controller/irq.h>
#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/pinctrl/pinctrl-zynqmp.h>
+#include <dt-bindings/phy/phy.h>
/ {
model = "ZynqMP ZCU100 RevC";
compatible = "xlnx,zynqmp-zcu100-revC", "xlnx,zynqmp-zcu100", "xlnx,zynqmp";
aliases {
+ gpio0 = &gpio;
i2c0 = &i2c1;
rtc0 = &rtc;
serial0 = &uart1;
serial2 = &dcc;
spi0 = &spi0;
spi1 = &spi1;
+ usb0 = &usb0;
+ usb1 = &usb1;
mmc0 = &sdhci0;
mmc1 = &sdhci1;
};
label = "sw4";
gpios = <&gpio 23 GPIO_ACTIVE_LOW>;
linux,code = <KEY_POWER>;
- wakeup-source;
+ gpio-key,wakeup;
autorepeat;
};
};
+ iio-hwmon {
+ compatible = "iio-hwmon";
+ io-channels = <&xilinx_ams 0>, <&xilinx_ams 1>, <&xilinx_ams 2>,
+ <&xilinx_ams 3>, <&xilinx_ams 4>, <&xilinx_ams 5>,
+ <&xilinx_ams 6>, <&xilinx_ams 7>, <&xilinx_ams 8>,
+ <&xilinx_ams 9>, <&xilinx_ams 10>,
+ <&xilinx_ams 11>, <&xilinx_ams 12>;
+ };
+
leds {
compatible = "gpio-leds";
ds2 {
linux,default-trigger = "bluetooth-power";
};
- vbus-det { /* U5 USB5744 VBUS detection via MIO25 */
+ vbus_det { /* U5 USB5744 VBUS detection via MIO25 */
label = "vbus_det";
gpios = <&gpio 25 GPIO_ACTIVE_HIGH>;
default-state = "on";
};
};
+ ltc2954: ltc2954 { /* U7 */
+ compatible = "lltc,ltc2954", "lltc,ltc2952";
+ status = "disabled";
+ trigger-gpios = <&gpio 26 GPIO_ACTIVE_LOW>; /* INT line - input */
+ /* If there is HW watchdog on mezzanine this signal should be connected there */
+ watchdog-gpios = <&gpio 35 GPIO_ACTIVE_HIGH>; /* MIO on PAD */
+ kill-gpios = <&gpio 34 GPIO_ACTIVE_LOW>; /* KILL signal - output */
+ };
+
wmmcsdio_fixed: fixedregulator-mmcsdio {
compatible = "regulator-fixed";
regulator-name = "wmmcsdio_fixed";
regulator-boot-on;
};
- sdio_pwrseq: sdio-pwrseq {
+ sdio_pwrseq: sdio_pwrseq {
compatible = "mmc-pwrseq-simple";
reset-gpios = <&gpio 7 GPIO_ACTIVE_LOW>; /* WIFI_EN */
- post-power-on-delay-ms = <10>;
};
};
"", "", "", "";
};
+&gpu {
+ status = "okay";
+};
+
&i2c1 {
status = "okay";
+ pinctrl-names = "default", "gpio";
+ pinctrl-0 = <&pinctrl_i2c1_default>;
+ pinctrl-1 = <&pinctrl_i2c1_gpio>;
+ scl-gpios = <&gpio 4 GPIO_ACTIVE_HIGH>;
+ sda-gpios = <&gpio 5 GPIO_ACTIVE_HIGH>;
clock-frequency = <100000>;
i2c-mux@75 { /* u11 */
compatible = "nxp,pca9548";
};
};
+&pinctrl0 {
+ status = "okay";
+ pinctrl_i2c1_default: i2c1-default {
+ mux {
+ groups = "i2c1_1_grp";
+ function = "i2c1";
+ };
+
+ conf {
+ groups = "i2c1_1_grp";
+ bias-pull-up;
+ slew-rate = <SLEW_RATE_SLOW>;
+ io-standard = <IO_STANDARD_LVCMOS18>;
+ };
+ };
+
+ pinctrl_i2c1_gpio: i2c1-gpio {
+ mux {
+ groups = "gpio0_4_grp", "gpio0_5_grp";
+ function = "gpio0";
+ };
+
+ conf {
+ groups = "gpio0_4_grp", "gpio0_5_grp";
+ slew-rate = <SLEW_RATE_SLOW>;
+ io-standard = <IO_STANDARD_LVCMOS18>;
+ };
+ };
+
+ pinctrl_sdhci0_default: sdhci0-default {
+ mux {
+ groups = "sdio0_3_grp";
+ function = "sdio0";
+ };
+
+ conf {
+ groups = "sdio0_3_grp";
+ slew-rate = <SLEW_RATE_SLOW>;
+ io-standard = <IO_STANDARD_LVCMOS18>;
+ bias-disable;
+ };
+
+ mux-cd {
+ groups = "sdio0_cd_0_grp";
+ function = "sdio0_cd";
+ };
+
+ conf-cd {
+ groups = "sdio0_cd_0_grp";
+ bias-high-impedance;
+ bias-pull-up;
+ slew-rate = <SLEW_RATE_SLOW>;
+ io-standard = <IO_STANDARD_LVCMOS18>;
+ };
+ };
+
+ pinctrl_sdhci1_default: sdhci1-default {
+ mux {
+ groups = "sdio1_2_grp";
+ function = "sdio1";
+ };
+
+ conf {
+ groups = "sdio1_2_grp";
+ slew-rate = <SLEW_RATE_SLOW>;
+ io-standard = <IO_STANDARD_LVCMOS18>;
+ bias-disable;
+ };
+ };
+
+ pinctrl_spi0_default: spi0-default {
+ mux {
+ groups = "spi0_3_grp";
+ function = "spi0";
+ };
+
+ conf {
+ groups = "spi0_3_grp";
+ bias-disable;
+ slew-rate = <SLEW_RATE_SLOW>;
+ io-standard = <IO_STANDARD_LVCMOS18>;
+ };
+
+ mux-cs {
+ groups = "spi0_ss_9_grp";
+ function = "spi0_ss";
+ };
+
+ conf-cs {
+ groups = "spi0_ss_9_grp";
+ bias-disable;
+ };
+
+ };
+
+ pinctrl_spi1_default: spi1-default {
+ mux {
+ groups = "spi1_0_grp";
+ function = "spi1";
+ };
+
+ conf {
+ groups = "spi1_0_grp";
+ bias-disable;
+ slew-rate = <SLEW_RATE_SLOW>;
+ io-standard = <IO_STANDARD_LVCMOS18>;
+ };
+
+ mux-cs {
+ groups = "spi1_ss_0_grp";
+ function = "spi1_ss";
+ };
+
+ conf-cs {
+ groups = "spi1_ss_0_grp";
+ bias-disable;
+ };
+
+ };
+
+ pinctrl_uart0_default: uart0-default {
+ mux {
+ groups = "uart0_0_grp";
+ function = "uart0";
+ };
+
+ conf {
+ groups = "uart0_0_grp";
+ slew-rate = <SLEW_RATE_SLOW>;
+ io-standard = <IO_STANDARD_LVCMOS18>;
+ };
+
+ conf-rx {
+ pins = "MIO3";
+ bias-high-impedance;
+ };
+
+ conf-tx {
+ pins = "MIO2";
+ bias-disable;
+ };
+ };
+
+ pinctrl_uart1_default: uart1-default {
+ mux {
+ groups = "uart1_0_grp";
+ function = "uart1";
+ };
+
+ conf {
+ groups = "uart1_0_grp";
+ slew-rate = <SLEW_RATE_SLOW>;
+ io-standard = <IO_STANDARD_LVCMOS18>;
+ };
+
+ conf-rx {
+ pins = "MIO1";
+ bias-high-impedance;
+ };
+
+ conf-tx {
+ pins = "MIO0";
+ bias-disable;
+ };
+ };
+
+ pinctrl_usb0_default: usb0-default {
+ mux {
+ groups = "usb0_0_grp";
+ function = "usb0";
+ };
+
+ conf {
+ groups = "usb0_0_grp";
+ slew-rate = <SLEW_RATE_SLOW>;
+ io-standard = <IO_STANDARD_LVCMOS18>;
+ };
+
+ conf-rx {
+ pins = "MIO52", "MIO53", "MIO55";
+ bias-high-impedance;
+ };
+
+ conf-tx {
+ pins = "MIO54", "MIO56", "MIO57", "MIO58", "MIO59",
+ "MIO60", "MIO61", "MIO62", "MIO63";
+ bias-disable;
+ };
+ };
+
+ pinctrl_usb1_default: usb1-default {
+ mux {
+ groups = "usb1_0_grp";
+ function = "usb1";
+ };
+
+ conf {
+ groups = "usb1_0_grp";
+ slew-rate = <SLEW_RATE_SLOW>;
+ io-standard = <IO_STANDARD_LVCMOS18>;
+ };
+
+ conf-rx {
+ pins = "MIO64", "MIO65", "MIO67";
+ bias-high-impedance;
+ };
+
+ conf-tx {
+ pins = "MIO66", "MIO68", "MIO69", "MIO70", "MIO71",
+ "MIO72", "MIO73", "MIO74", "MIO75";
+ bias-disable;
+ };
+ };
+};
+
&rtc {
status = "okay";
};
&sdhci0 {
status = "okay";
no-1-8-v;
- broken-cd; /* CD has to be enabled by default */
disable-wp;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_sdhci0_default>;
+ xlnx,mio_bank = <0>;
};
&sdhci1 {
status = "okay";
bus-width = <0x4>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_sdhci1_default>;
+ xlnx,mio_bank = <0>;
non-removable;
disable-wp;
cap-power-off-card;
};
};
+&serdes {
+ status = "okay";
+};
+
&spi0 { /* Low Speed connector */
status = "okay";
label = "LS-SPI0";
+ num-cs = <1>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_spi0_default>;
};
&spi1 { /* High Speed connector */
status = "okay";
label = "HS-SPI1";
+ num-cs = <1>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_spi1_default>;
};
&uart0 {
status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart0_default>;
bluetooth {
compatible = "ti,wl1831-st";
enable-gpios = <&gpio 8 GPIO_ACTIVE_HIGH>;
&uart1 {
status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart1_default>;
};
/* ULPI SMSC USB3320 */
&usb0 {
status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usb0_default>;
+};
+
+&dwc3_0 {
+ status = "okay";
+ dr_mode = "peripheral";
+ phy-names = "usb3-phy";
+ phys = <&lane2 PHY_TYPE_USB3 0 0 26000000>;
+ maximum-speed = "super-speed";
};
/* ULPI SMSC USB3320 */
&usb1 {
status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usb1_default>;
+};
+
+&dwc3_1 {
+ status = "okay";
+ dr_mode = "host";
+ phy-names = "usb3-phy";
+ phys = <&lane3 PHY_TYPE_USB3 1 0 26000000>;
+ maximum-speed = "super-speed";
};
&watchdog0 {
status = "okay";
};
+
+&zynqmp_dpsub {
+ status = "okay";
+ phy-names = "dp-phy0", "dp-phy1";
+ phys = <&lane1 PHY_TYPE_DP 0 1 27000000>,
+ <&lane0 PHY_TYPE_DP 1 1 27000000>;
+};
+
+&zynqmp_dp_snd_pcm0 {
+ status = "okay";
+};
+
+&zynqmp_dp_snd_pcm1 {
+ status = "okay";
+};
+
+&zynqmp_dp_snd_card0 {
+ status = "okay";
+};
+
+&zynqmp_dp_snd_codec0 {
+ status = "okay";
+};
+
+&xlnx_dpdma {
+ status = "okay";
+};
+
+&xilinx_ams {
+ status = "okay";
+};
+
+&ams_ps {
+ status = "okay";
+};
/dts-v1/;
#include "zynqmp.dtsi"
-#include "zynqmp-clk.dtsi"
+#include "zynqmp-clk-ccf.dtsi"
#include <dt-bindings/input/input.h>
#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/pinctrl/pinctrl-zynqmp.h>
+#include <dt-bindings/phy/phy.h>
/ {
model = "ZynqMP ZCU102 RevA";
aliases {
ethernet0 = &gem3;
+ gpio0 = &gpio;
i2c0 = &i2c0;
i2c1 = &i2c1;
mmc0 = &sdhci1;
serial0 = &uart0;
serial1 = &uart1;
serial2 = &dcc;
+ spi0 = &qspi;
+ usb0 = &usb0;
};
chosen {
bootargs = "earlycon";
stdout-path = "serial0:115200n8";
+ xlnx,eeprom = &eeprom;
};
memory@0 {
label = "sw19";
gpios = <&gpio 22 GPIO_ACTIVE_HIGH>;
linux,code = <KEY_DOWN>;
- wakeup-source;
+ gpio-key,wakeup;
autorepeat;
};
};
leds {
compatible = "gpio-leds";
- heartbeat-led {
+ heartbeat_led {
label = "heartbeat";
gpios = <&gpio 23 GPIO_ACTIVE_HIGH>;
linux,default-trigger = "heartbeat";
&can1 {
status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_can1_default>;
};
&dcc {
status = "okay";
phy-handle = <&phy0>;
phy-mode = "rgmii-id";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_gem3_default>;
phy0: phy@21 {
reg = <21>;
ti,rx-internal-delay = <0x8>;
ti,tx-internal-delay = <0xa>;
ti,fifo-depth = <0x1>;
+ ti,dp83867-rxctrl-strap-quirk;
+ /* reset-gpios = <&tca6416_u97 6 GPIO_ACTIVE_LOW>; */
};
};
&gpio {
status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_gpio_default>;
+};
+
+&gpu {
+ status = "okay";
};
&i2c0 {
status = "okay";
clock-frequency = <400000>;
+ pinctrl-names = "default", "gpio";
+ pinctrl-0 = <&pinctrl_i2c0_default>;
+ pinctrl-1 = <&pinctrl_i2c0_gpio>;
+ scl-gpios = <&gpio 14 GPIO_ACTIVE_HIGH>;
+ sda-gpios = <&gpio 15 GPIO_ACTIVE_HIGH>;
tca6416_u97: gpio@20 {
compatible = "ti,tca6416";
reg = <0x20>;
- gpio-controller;
+ gpio-controller; /* IRQ not connected */
#gpio-cells = <2>;
- /*
- * IRQ not connected
- * Lines:
- * 0 - PS_GTR_LAN_SEL0
- * 1 - PS_GTR_LAN_SEL1
- * 2 - PS_GTR_LAN_SEL2
- * 3 - PS_GTR_LAN_SEL3
- * 4 - PCI_CLK_DIR_SEL
- * 5 - IIC_MUX_RESET_B
- * 6 - GEM3_EXP_RESET_B
- * 7, 10 - 17 - not connected
- */
-
- gtr-sel0 {
+ gpio-line-names = "PS_GTR_LAN_SEL0", "PS_GTR_LAN_SEL1", "PS_GTR_LAN_SEL2", "PS_GTR_LAN_SEL3",
+ "PCI_CLK_DIR_SEL", "IIC_MUX_RESET_B", "GEM3_EXP_RESET_B",
+ "", "", "", "", "", "", "", "", "";
+ gtr_sel0 {
gpio-hog;
gpios = <0 0>;
output-low; /* PCIE = 0, DP = 1 */
line-name = "sel0";
};
- gtr-sel1 {
+ gtr_sel1 {
gpio-hog;
gpios = <1 0>;
output-high; /* PCIE = 0, DP = 1 */
line-name = "sel1";
};
- gtr-sel2 {
+ gtr_sel2 {
gpio-hog;
gpios = <2 0>;
output-high; /* PCIE = 0, USB0 = 1 */
line-name = "sel2";
};
- gtr-sel3 {
+ gtr_sel3 {
gpio-hog;
gpios = <3 0>;
output-high; /* PCIE = 0, SATA = 1 */
tca6416_u61: gpio@21 {
compatible = "ti,tca6416";
reg = <0x21>;
- gpio-controller;
+ gpio-controller; /* IRQ not connected */
#gpio-cells = <2>;
- /*
- * IRQ not connected
- * Lines:
- * 0 - VCCPSPLL_EN
- * 1 - MGTRAVCC_EN
- * 2 - MGTRAVTT_EN
- * 3 - VCCPSDDRPLL_EN
- * 4 - MIO26_PMU_INPUT_LS
- * 5 - PL_PMBUS_ALERT
- * 6 - PS_PMBUS_ALERT
- * 7 - MAXIM_PMBUS_ALERT
- * 10 - PL_DDR4_VTERM_EN
- * 11 - PL_DDR4_VPP_2V5_EN
- * 12 - PS_DIMM_VDDQ_TO_PSVCCO_ON
- * 13 - PS_DIMM_SUSPEND_EN
- * 14 - PS_DDR4_VTERM_EN
- * 15 - PS_DDR4_VPP_2V5_EN
- * 16 - 17 - not connected
- */
+ gpio-line-names = "VCCPSPLL_EN", "MGTRAVCC_EN", "MGTRAVTT_EN", "VCCPSDDRPLL_EN", "MIO26_PMU_INPUT_LS",
+ "PL_PMBUS_ALERT", "PS_PMBUS_ALERT", "MAXIM_PMBUS_ALERT", "PL_DDR4_VTERM_EN",
+ "PL_DDR4_VPP_2V5_EN", "PS_DIMM_VDDQ_TO_PSVCCO_ON", "PS_DIMM_SUSPEND_EN",
+ "PS_DDR4_VTERM_EN", "PS_DDR4_VPP_2V5_EN", "", "";
};
i2c-mux@75 { /* u60 */
status = "disabled"; /* unreachable */
reg = <0x20>;
};
-
max20751@72 { /* u95 */
compatible = "maxim,max20751";
reg = <0x72>;
&i2c1 {
status = "okay";
clock-frequency = <400000>;
+ pinctrl-names = "default", "gpio";
+ pinctrl-0 = <&pinctrl_i2c1_default>;
+ pinctrl-1 = <&pinctrl_i2c1_gpio>;
+ scl-gpios = <&gpio 16 GPIO_ACTIVE_HIGH>;
+ sda-gpios = <&gpio 17 GPIO_ACTIVE_HIGH>;
/* PL i2c via PCA9306 - u45 */
i2c-mux@74 { /* u34 */
#size-cells = <0>;
reg = <1>;
si5341: clock-generator@36 { /* SI5341 - u69 */
+ compatible = "silabs,si5341";
reg = <0x36>;
};
temperature-stability = <50>;
factory-fout = <300000000>;
clock-frequency = <300000000>;
+ clock-output-names = "si570_user";
};
};
i2c@3 {
temperature-stability = <50>; /* copy from zc702 */
factory-fout = <156250000>;
clock-frequency = <148500000>;
+ clock-output-names = "si570_mgt";
};
};
i2c@4 {
#size-cells = <0>;
reg = <4>;
si5328: clock-generator@69 {/* SI5328 - u20 */
+ compatible = "silabs,si5328";
reg = <0x69>;
/*
* Chip has interrupt present connected to PL
};
};
+&pinctrl0 {
+ status = "okay";
+ pinctrl_i2c0_default: i2c0-default {
+ mux {
+ groups = "i2c0_3_grp";
+ function = "i2c0";
+ };
+
+ conf {
+ groups = "i2c0_3_grp";
+ bias-pull-up;
+ slew-rate = <SLEW_RATE_SLOW>;
+ io-standard = <IO_STANDARD_LVCMOS18>;
+ };
+ };
+
+ pinctrl_i2c0_gpio: i2c0-gpio {
+ mux {
+ groups = "gpio0_14_grp", "gpio0_15_grp";
+ function = "gpio0";
+ };
+
+ conf {
+ groups = "gpio0_14_grp", "gpio0_15_grp";
+ slew-rate = <SLEW_RATE_SLOW>;
+ io-standard = <IO_STANDARD_LVCMOS18>;
+ };
+ };
+
+ pinctrl_i2c1_default: i2c1-default {
+ mux {
+ groups = "i2c1_4_grp";
+ function = "i2c1";
+ };
+
+ conf {
+ groups = "i2c1_4_grp";
+ bias-pull-up;
+ slew-rate = <SLEW_RATE_SLOW>;
+ io-standard = <IO_STANDARD_LVCMOS18>;
+ };
+ };
+
+ pinctrl_i2c1_gpio: i2c1-gpio {
+ mux {
+ groups = "gpio0_16_grp", "gpio0_17_grp";
+ function = "gpio0";
+ };
+
+ conf {
+ groups = "gpio0_16_grp", "gpio0_17_grp";
+ slew-rate = <SLEW_RATE_SLOW>;
+ io-standard = <IO_STANDARD_LVCMOS18>;
+ };
+ };
+
+ pinctrl_uart0_default: uart0-default {
+ mux {
+ groups = "uart0_4_grp";
+ function = "uart0";
+ };
+
+ conf {
+ groups = "uart0_4_grp";
+ slew-rate = <SLEW_RATE_SLOW>;
+ io-standard = <IO_STANDARD_LVCMOS18>;
+ };
+
+ conf-rx {
+ pins = "MIO18";
+ bias-high-impedance;
+ };
+
+ conf-tx {
+ pins = "MIO19";
+ bias-disable;
+ };
+ };
+
+ pinctrl_uart1_default: uart1-default {
+ mux {
+ groups = "uart1_5_grp";
+ function = "uart1";
+ };
+
+ conf {
+ groups = "uart1_5_grp";
+ slew-rate = <SLEW_RATE_SLOW>;
+ io-standard = <IO_STANDARD_LVCMOS18>;
+ };
+
+ conf-rx {
+ pins = "MIO21";
+ bias-high-impedance;
+ };
+
+ conf-tx {
+ pins = "MIO20";
+ bias-disable;
+ };
+ };
+
+ pinctrl_usb0_default: usb0-default {
+ mux {
+ groups = "usb0_0_grp";
+ function = "usb0";
+ };
+
+ conf {
+ groups = "usb0_0_grp";
+ slew-rate = <SLEW_RATE_SLOW>;
+ io-standard = <IO_STANDARD_LVCMOS18>;
+ };
+
+ conf-rx {
+ pins = "MIO52", "MIO53", "MIO55";
+ bias-high-impedance;
+ };
+
+ conf-tx {
+ pins = "MIO54", "MIO56", "MIO57", "MIO58", "MIO59",
+ "MIO60", "MIO61", "MIO62", "MIO63";
+ bias-disable;
+ };
+ };
+
+ pinctrl_gem3_default: gem3-default {
+ mux {
+ function = "ethernet3";
+ groups = "ethernet3_0_grp";
+ };
+
+ conf {
+ groups = "ethernet3_0_grp";
+ slew-rate = <SLEW_RATE_SLOW>;
+ io-standard = <IO_STANDARD_LVCMOS18>;
+ };
+
+ conf-rx {
+ pins = "MIO70", "MIO71", "MIO72", "MIO73", "MIO74",
+ "MIO75";
+ bias-high-impedance;
+ low-power-disable;
+ };
+
+ conf-tx {
+ pins = "MIO64", "MIO65", "MIO66", "MIO67", "MIO68",
+ "MIO69";
+ bias-disable;
+ low-power-enable;
+ };
+
+ mux-mdio {
+ function = "mdio3";
+ groups = "mdio3_0_grp";
+ };
+
+ conf-mdio {
+ groups = "mdio3_0_grp";
+ slew-rate = <SLEW_RATE_SLOW>;
+ io-standard = <IO_STANDARD_LVCMOS18>;
+ bias-disable;
+ };
+ };
+
+ pinctrl_can1_default: can1-default {
+ mux {
+ function = "can1";
+ groups = "can1_6_grp";
+ };
+
+ conf {
+ groups = "can1_6_grp";
+ slew-rate = <SLEW_RATE_SLOW>;
+ io-standard = <IO_STANDARD_LVCMOS18>;
+ };
+
+ conf-rx {
+ pins = "MIO25";
+ bias-high-impedance;
+ };
+
+ conf-tx {
+ pins = "MIO24";
+ bias-disable;
+ };
+ };
+
+ pinctrl_sdhci1_default: sdhci1-default {
+ mux {
+ groups = "sdio1_0_grp";
+ function = "sdio1";
+ };
+
+ conf {
+ groups = "sdio1_0_grp";
+ slew-rate = <SLEW_RATE_SLOW>;
+ io-standard = <IO_STANDARD_LVCMOS18>;
+ bias-disable;
+ };
+
+ mux-cd {
+ groups = "sdio1_cd_0_grp";
+ function = "sdio1_cd";
+ };
+
+ conf-cd {
+ groups = "sdio1_cd_0_grp";
+ bias-high-impedance;
+ bias-pull-up;
+ slew-rate = <SLEW_RATE_SLOW>;
+ io-standard = <IO_STANDARD_LVCMOS18>;
+ };
+
+ mux-wp {
+ groups = "sdio1_wp_0_grp";
+ function = "sdio1_wp";
+ };
+
+ conf-wp {
+ groups = "sdio1_wp_0_grp";
+ bias-high-impedance;
+ bias-pull-up;
+ slew-rate = <SLEW_RATE_SLOW>;
+ io-standard = <IO_STANDARD_LVCMOS18>;
+ };
+ };
+
+ pinctrl_gpio_default: gpio-default {
+ mux-sw {
+ function = "gpio0";
+ groups = "gpio0_22_grp", "gpio0_23_grp";
+ };
+
+ conf-sw {
+ groups = "gpio0_22_grp", "gpio0_23_grp";
+ slew-rate = <SLEW_RATE_SLOW>;
+ io-standard = <IO_STANDARD_LVCMOS18>;
+ };
+
+ mux-msp {
+ function = "gpio0";
+ groups = "gpio0_13_grp", "gpio0_38_grp";
+ };
+
+ conf-msp {
+ groups = "gpio0_13_grp", "gpio0_38_grp";
+ slew-rate = <SLEW_RATE_SLOW>;
+ io-standard = <IO_STANDARD_LVCMOS18>;
+ };
+
+ conf-pull-up {
+ pins = "MIO22", "MIO23";
+ bias-pull-up;
+ };
+
+ conf-pull-none {
+ pins = "MIO13", "MIO38";
+ bias-disable;
+ };
+ };
+};
+
&pcie {
status = "okay";
};
+&qspi {
+ status = "okay";
+ is-dual = <1>;
+ flash@0 {
+ compatible = "m25p80", "spi-flash"; /* 32MB */
+ #address-cells = <1>;
+ #size-cells = <1>;
+ reg = <0x0>;
+ spi-tx-bus-width = <1>;
+ spi-rx-bus-width = <4>; /* FIXME also DUAL configuration possible */
+ spi-max-frequency = <108000000>; /* Based on DC1 spec */
+ partition@qspi-fsbl-uboot { /* for testing purpose */
+ label = "qspi-fsbl-uboot";
+ reg = <0x0 0x100000>;
+ };
+ partition@qspi-linux { /* for testing purpose */
+ label = "qspi-linux";
+ reg = <0x100000 0x500000>;
+ };
+ partition@qspi-device-tree { /* for testing purpose */
+ label = "qspi-device-tree";
+ reg = <0x600000 0x20000>;
+ };
+ partition@qspi-rootfs { /* for testing purpose */
+ label = "qspi-rootfs";
+ reg = <0x620000 0x5E0000>;
+ };
+ };
+};
+
&rtc {
status = "okay";
};
ceva,p1-comwake-params = /bits/ 8 <0x06 0x14 0x08 0x0E>;
ceva,p1-burst-params = /bits/ 8 <0x13 0x08 0x4A 0x06>;
ceva,p1-retry-params = /bits/ 16 <0x96A4 0x3FFC>;
+ phy-names = "sata-phy";
+ phys = <&lane3 PHY_TYPE_SATA 1 1 125000000>;
};
/* SD1 with level shifter */
&sdhci1 {
status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_sdhci1_default>;
no-1-8-v;
+ xlnx,mio_bank = <1>;
+};
+
+&serdes {
+ status = "okay";
};
&uart0 {
status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart0_default>;
};
&uart1 {
status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart1_default>;
};
/* ULPI SMSC USB3320 */
&usb0 {
status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usb0_default>;
+};
+
+&dwc3_0 {
+ status = "okay";
+ dr_mode = "host";
+ snps,usb3_lpm_capable;
+ phy-names = "usb3-phy";
+ phys = <&lane2 PHY_TYPE_USB3 0 2 26000000>;
+ maximum-speed = "super-speed";
};
&watchdog0 {
status = "okay";
};
+
+&xilinx_ams {
+ status = "okay";
+};
+
+&ams_ps {
+ status = "okay";
+};
+
+&ams_pl {
+ status = "okay";
+};
+
+&zynqmp_dpsub {
+ status = "okay";
+ phy-names = "dp-phy0";
+ phys = <&lane1 PHY_TYPE_DP 0 3 27000000>;
+};
+
+&zynqmp_dp_snd_codec0 {
+ status = "okay";
+};
+
+&zynqmp_dp_snd_pcm0 {
+ status = "okay";
+};
+
+&zynqmp_dp_snd_pcm1 {
+ status = "okay";
+};
+
+&zynqmp_dp_snd_card0 {
+ status = "okay";
+};
+
+&xlnx_dpdma {
+ status = "okay";
+};
ti,rx-internal-delay = <0x8>;
ti,tx-internal-delay = <0xa>;
ti,fifo-depth = <0x1>;
+ ti,dp83867-rxctrl-strap-quirk;
+ /* reset-gpios = <&tca6416_u97 6 GPIO_ACTIVE_LOW>; */
};
/* Cleanup from RevA */
/delete-node/ phy@21;
/dts-v1/;
#include "zynqmp.dtsi"
-#include "zynqmp-clk.dtsi"
+#include "zynqmp-clk-ccf.dtsi"
#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/pinctrl/pinctrl-zynqmp.h>
+#include <dt-bindings/phy/phy.h>
/ {
model = "ZynqMP ZCU104 RevA";
aliases {
ethernet0 = &gem3;
+ gpio0 = &gpio;
i2c0 = &i2c1;
mmc0 = &sdhci1;
rtc0 = &rtc;
serial0 = &uart0;
serial1 = &uart1;
serial2 = &dcc;
+ spi0 = &qspi;
+ usb0 = &usb0;
};
chosen {
&can1 {
status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_can1_default>;
};
&dcc {
status = "okay";
};
+&fpd_dma_chan1 {
+ status = "okay";
+};
+
+&fpd_dma_chan2 {
+ status = "okay";
+};
+
+&fpd_dma_chan3 {
+ status = "okay";
+};
+
+&fpd_dma_chan4 {
+ status = "okay";
+};
+
+&fpd_dma_chan5 {
+ status = "okay";
+};
+
+&fpd_dma_chan6 {
+ status = "okay";
+};
+
+&fpd_dma_chan7 {
+ status = "okay";
+};
+
+&fpd_dma_chan8 {
+ status = "okay";
+};
+
&gem3 {
status = "okay";
phy-handle = <&phy0>;
phy-mode = "rgmii-id";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_gem3_default>;
phy0: phy@c {
reg = <0xc>;
ti,rx-internal-delay = <0x8>;
ti,tx-internal-delay = <0xa>;
ti,fifo-depth = <0x1>;
+ ti,dp83867-rxctrl-strap-quirk;
};
};
status = "okay";
};
+&gpu {
+ status = "okay";
+};
+
&i2c1 {
status = "okay";
clock-frequency = <400000>;
+ pinctrl-names = "default", "gpio";
+ pinctrl-0 = <&pinctrl_i2c1_default>;
+ pinctrl-1 = <&pinctrl_i2c1_gpio>;
+ scl-gpios = <&gpio 16 GPIO_ACTIVE_HIGH>;
+ sda-gpios = <&gpio 17 GPIO_ACTIVE_HIGH>;
/* Another connection to this bus via PL i2c via PCA9306 - u45 */
i2c-mux@74 { /* u34 */
* 512B - 768B address 0x56
* 768B - 1024B address 0x57
*/
- eeprom@54 { /* u23 */
+ eeprom: eeprom@54 { /* u23 */
compatible = "atmel,24c08";
reg = <0x54>;
#address-cells = <1>;
#size-cells = <0>;
reg = <1>;
clock_8t49n287: clock-generator@6c { /* 8T49N287 - u182 */
+ compatible = "idt,8t49n287";
reg = <0x6c>;
};
};
#size-cells = <0>;
reg = <2>;
irps5401_43: irps54012@43 { /* IRPS5401 - u175 */
+ #clock-cells = <0>;
+ compatible = "infineon,irps5401";
reg = <0x43>;
};
irps5401_4d: irps54012@4d { /* IRPS5401 - u180 */
+ #clock-cells = <0>;
+ compatible = "infineon,irps5401";
reg = <0x4d>;
};
};
#address-cells = <1>;
#size-cells = <0>;
reg = <4>;
- tca6416_u97: gpio@21 {
+ tca6416_u97: gpio@20 {
compatible = "ti,tca6416";
- reg = <0x21>;
+ reg = <0x20>;
gpio-controller;
#gpio-cells = <2>;
/*
};
};
+&pinctrl0 {
+ status = "okay";
+
+ pinctrl_can1_default: can1-default {
+ mux {
+ function = "can1";
+ groups = "can1_6_grp";
+ };
+
+ conf {
+ groups = "can1_6_grp";
+ slew-rate = <SLEW_RATE_SLOW>;
+ io-standard = <IO_STANDARD_LVCMOS18>;
+ drive-strength = <12>;
+ };
+
+ conf-rx {
+ pins = "MIO25";
+ bias-high-impedance;
+ };
+
+ conf-tx {
+ pins = "MIO24";
+ bias-disable;
+ };
+ };
+
+ pinctrl_i2c1_default: i2c1-default {
+ mux {
+ groups = "i2c1_4_grp";
+ function = "i2c1";
+ };
+
+ conf {
+ groups = "i2c1_4_grp";
+ bias-pull-up;
+ slew-rate = <SLEW_RATE_SLOW>;
+ io-standard = <IO_STANDARD_LVCMOS18>;
+ drive-strength = <12>;
+ };
+ };
+
+ pinctrl_i2c1_gpio: i2c1-gpio {
+ mux {
+ groups = "gpio0_16_grp", "gpio0_17_grp";
+ function = "gpio0";
+ };
+
+ conf {
+ groups = "gpio0_16_grp", "gpio0_17_grp";
+ slew-rate = <SLEW_RATE_SLOW>;
+ io-standard = <IO_STANDARD_LVCMOS18>;
+ drive-strength = <12>;
+ };
+ };
+
+ pinctrl_gem3_default: gem3-default {
+ mux {
+ function = "ethernet3";
+ groups = "ethernet3_0_grp";
+ };
+
+ conf {
+ groups = "ethernet3_0_grp";
+ slew-rate = <SLEW_RATE_SLOW>;
+ io-standard = <IO_STANDARD_LVCMOS18>;
+ drive-strength = <12>;
+ };
+
+ conf-rx {
+ pins = "MIO70", "MIO71", "MIO72", "MIO73", "MIO74",
+ "MIO75";
+ bias-high-impedance;
+ low-power-disable;
+ };
+
+ conf-tx {
+ pins = "MIO64", "MIO65", "MIO66", "MIO67", "MIO68",
+ "MIO69";
+ bias-disable;
+ low-power-enable;
+ };
+
+ mux-mdio {
+ function = "mdio3";
+ groups = "mdio3_0_grp";
+ };
+
+ conf-mdio {
+ groups = "mdio3_0_grp";
+ slew-rate = <SLEW_RATE_SLOW>;
+ io-standard = <IO_STANDARD_LVCMOS18>;
+ bias-disable;
+ };
+ };
+
+ pinctrl_sdhci1_default: sdhci1-default {
+ mux {
+ groups = "sdio1_0_grp";
+ function = "sdio1";
+ };
+
+ conf {
+ groups = "sdio1_0_grp";
+ slew-rate = <SLEW_RATE_SLOW>;
+ io-standard = <IO_STANDARD_LVCMOS18>;
+ bias-disable;
+ drive-strength = <12>;
+ };
+
+ mux-cd {
+ groups = "sdio1_cd_0_grp";
+ function = "sdio1_cd";
+ };
+
+ conf-cd {
+ groups = "sdio1_cd_0_grp";
+ bias-high-impedance;
+ bias-pull-up;
+ slew-rate = <SLEW_RATE_SLOW>;
+ io-standard = <IO_STANDARD_LVCMOS18>;
+ };
+ };
+
+ pinctrl_uart0_default: uart0-default {
+ mux {
+ groups = "uart0_4_grp";
+ function = "uart0";
+ };
+
+ conf {
+ groups = "uart0_4_grp";
+ slew-rate = <SLEW_RATE_SLOW>;
+ io-standard = <IO_STANDARD_LVCMOS18>;
+ drive-strength = <12>;
+ };
+
+ conf-rx {
+ pins = "MIO18";
+ bias-high-impedance;
+ };
+
+ conf-tx {
+ pins = "MIO19";
+ bias-disable;
+ };
+ };
+
+ pinctrl_uart1_default: uart1-default {
+ mux {
+ groups = "uart1_5_grp";
+ function = "uart1";
+ };
+
+ conf {
+ groups = "uart1_5_grp";
+ slew-rate = <SLEW_RATE_SLOW>;
+ io-standard = <IO_STANDARD_LVCMOS18>;
+ drive-strength = <12>;
+ };
+
+ conf-rx {
+ pins = "MIO21";
+ bias-high-impedance;
+ };
+
+ conf-tx {
+ pins = "MIO20";
+ bias-disable;
+ };
+ };
+
+ pinctrl_usb0_default: usb0-default {
+ mux {
+ groups = "usb0_0_grp";
+ function = "usb0";
+ };
+
+ conf {
+ groups = "usb0_0_grp";
+ slew-rate = <SLEW_RATE_SLOW>;
+ io-standard = <IO_STANDARD_LVCMOS18>;
+ drive-strength = <12>;
+ };
+
+ conf-rx {
+ pins = "MIO52", "MIO53", "MIO55";
+ bias-high-impedance;
+ };
+
+ conf-tx {
+ pins = "MIO54", "MIO56", "MIO57", "MIO58", "MIO59",
+ "MIO60", "MIO61", "MIO62", "MIO63";
+ bias-disable;
+ };
+ };
+};
+
+&qspi {
+ status = "okay";
+ flash@0 {
+ compatible = "m25p80", "spi-flash"; /* n25q512a 128MiB */
+ #address-cells = <1>;
+ #size-cells = <1>;
+ reg = <0x0>;
+ spi-tx-bus-width = <1>;
+ spi-rx-bus-width = <4>;
+ spi-max-frequency = <108000000>; /* Based on DC1 spec */
+ partition@qspi-fsbl-uboot { /* for testing purpose */
+ label = "qspi-fsbl-uboot";
+ reg = <0x0 0x100000>;
+ };
+ partition@qspi-linux { /* for testing purpose */
+ label = "qspi-linux";
+ reg = <0x100000 0x500000>;
+ };
+ partition@qspi-device-tree { /* for testing purpose */
+ label = "qspi-device-tree";
+ reg = <0x600000 0x20000>;
+ };
+ partition@qspi-rootfs { /* for testing purpose */
+ label = "qspi-rootfs";
+ reg = <0x620000 0x5E0000>;
+ };
+ };
+};
+
&rtc {
status = "okay";
};
ceva,p1-comwake-params = /bits/ 8 <0x06 0x14 0x08 0x0E>;
ceva,p1-burst-params = /bits/ 8 <0x13 0x08 0x4A 0x06>;
ceva,p1-retry-params = /bits/ 16 <0x96A4 0x3FFC>;
+ phy-names = "sata-phy";
+ phys = <&lane3 PHY_TYPE_SATA 1 1 125000000>;
};
/* SD1 with level shifter */
&sdhci1 {
status = "okay";
no-1-8-v;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_sdhci1_default>;
+ xlnx,mio_bank = <1>;
disable-wp;
};
+&serdes {
+ status = "okay";
+};
+
&uart0 {
status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart0_default>;
};
&uart1 {
status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart1_default>;
};
/* ULPI SMSC USB3320 */
&usb0 {
status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usb0_default>;
+};
+
+&dwc3_0 {
+ status = "okay";
+ dr_mode = "host";
+ snps,usb3_lpm_capable;
+ phy-names = "usb3-phy";
+ phys = <&lane2 PHY_TYPE_USB3 0 2 26000000>;
+ maximum-speed = "super-speed";
};
&watchdog0 {
status = "okay";
};
+
+&xilinx_ams {
+ status = "okay";
+};
+
+&ams_ps {
+ status = "okay";
+};
+
+&ams_pl {
+ status = "okay";
+};
+
+&zynqmp_dpsub {
+ status = "okay";
+ phy-names = "dp-phy0", "dp-phy1";
+ phys = <&lane1 PHY_TYPE_DP 0 3 27000000>, <&lane0 PHY_TYPE_DP 1 3 27000000>;
+};
+
+&zynqmp_dp_snd_pcm0 {
+ status = "okay";
+};
+
+&zynqmp_dp_snd_pcm1 {
+ status = "okay";
+};
+
+&zynqmp_dp_snd_card0 {
+ status = "okay";
+};
+
+&zynqmp_dp_snd_codec0 {
+ status = "okay";
+};
+
+&xlnx_dpdma {
+ status = "okay";
+};
--- /dev/null
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * dts file for Xilinx ZynqMP ZCU104
+ *
+ * (C) Copyright 2017 - 2018, Xilinx, Inc.
+ *
+ * Michal Simek <michal.simek@xilinx.com>
+ */
+
+/dts-v1/;
+
+#include "zynqmp.dtsi"
+#include "zynqmp-clk-ccf.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/pinctrl/pinctrl-zynqmp.h>
+#include <dt-bindings/phy/phy.h>
+
+/ {
+ model = "ZynqMP ZCU104 RevC";
+ compatible = "xlnx,zynqmp-zcu104-revC", "xlnx,zynqmp-zcu104", "xlnx,zynqmp";
+
+ aliases {
+ ethernet0 = &gem3;
+ gpio0 = &gpio;
+ i2c0 = &i2c1;
+ mmc0 = &sdhci1;
+ rtc0 = &rtc;
+ serial0 = &uart0;
+ serial1 = &uart1;
+ serial2 = &dcc;
+ spi0 = &qspi;
+ usb0 = &usb0;
+ };
+
+ chosen {
+ bootargs = "earlycon";
+ stdout-path = "serial0:115200n8";
+ xlnx,eeprom = &eeprom;
+ };
+
+ memory@0 {
+ device_type = "memory";
+ reg = <0x0 0x0 0x0 0x80000000>;
+ };
+};
+
+&can1 {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_can1_default>;
+};
+
+&dcc {
+ status = "okay";
+};
+
+&fpd_dma_chan1 {
+ status = "okay";
+};
+
+&fpd_dma_chan2 {
+ status = "okay";
+};
+
+&fpd_dma_chan3 {
+ status = "okay";
+};
+
+&fpd_dma_chan4 {
+ status = "okay";
+};
+
+&fpd_dma_chan5 {
+ status = "okay";
+};
+
+&fpd_dma_chan6 {
+ status = "okay";
+};
+
+&fpd_dma_chan7 {
+ status = "okay";
+};
+
+&fpd_dma_chan8 {
+ status = "okay";
+};
+
+&gem3 {
+ status = "okay";
+ phy-handle = <&phy0>;
+ phy-mode = "rgmii-id";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_gem3_default>;
+ phy0: phy@c {
+ reg = <0xc>;
+ ti,rx-internal-delay = <0x8>;
+ ti,tx-internal-delay = <0xa>;
+ ti,fifo-depth = <0x1>;
+ ti,dp83867-rxctrl-strap-quirk;
+ };
+};
+
+&gpio {
+ status = "okay";
+};
+
+&gpu {
+ status = "okay";
+};
+
+&i2c1 {
+ status = "okay";
+ clock-frequency = <400000>;
+ pinctrl-names = "default", "gpio";
+ pinctrl-0 = <&pinctrl_i2c1_default>;
+ pinctrl-1 = <&pinctrl_i2c1_gpio>;
+ scl-gpios = <&gpio 16 GPIO_ACTIVE_HIGH>;
+ sda-gpios = <&gpio 17 GPIO_ACTIVE_HIGH>;
+
+ tca6416_u97: gpio@20 {
+ compatible = "ti,tca6416";
+ reg = <0x20>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ /*
+ * IRQ not connected
+ * Lines:
+ * 0 - IRPS5401_ALERT_B
+ * 1 - HDMI_8T49N241_INT_ALM
+ * 2 - MAX6643_OT_B
+ * 3 - MAX6643_FANFAIL_B
+ * 5 - IIC_MUX_RESET_B
+ * 6 - GEM3_EXP_RESET_B
+ * 7 - FMC_LPC_PRSNT_M2C_B
+ * 4, 10 - 17 - not connected
+ */
+ };
+
+ /* Another connection to this bus via PL i2c via PCA9306 - u45 */
+ i2c-mux@74 { /* u34 */
+ compatible = "nxp,pca9548";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x74>;
+ i2c@0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0>;
+ /*
+ * IIC_EEPROM 1kB memory which uses 256B blocks
+ * where every block has different address.
+ * 0 - 256B address 0x54
+ * 256B - 512B address 0x55
+ * 512B - 768B address 0x56
+ * 768B - 1024B address 0x57
+ */
+ eeprom: eeprom@54 { /* u23 */
+ compatible = "atmel,24c08";
+ reg = <0x54>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ };
+ };
+
+ i2c@1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <1>;
+ clock_8t49n287: clock-generator@6c { /* 8T49N287 - u182 */
+ compatible = "idt,8t49n287";
+ reg = <0x6c>;
+ };
+ };
+
+ i2c@2 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <2>;
+ irps5401_43: irps54012@43 { /* IRPS5401 - u175 */
+ #clock-cells = <0>;
+ compatible = "infineon,irps5401";
+ reg = <0x43>;
+ };
+ irps5401_4d: irps54012@4d { /* IRPS5401 - u180 */
+ #clock-cells = <0>;
+ compatible = "infineon,irps5401";
+ reg = <0x4d>;
+ };
+ };
+
+ i2c@3 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <3>;
+ ina226@40 { /* u183 */
+ compatible = "ti,ina226";
+ reg = <0x40>;
+ shunt-resistor = <5000>;
+ };
+ };
+
+ i2c@5 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <5>;
+ };
+
+ i2c@7 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <7>;
+ };
+
+ /* 4, 6 not connected */
+ };
+};
+
+&pinctrl0 {
+ status = "okay";
+
+ pinctrl_can1_default: can1-default {
+ mux {
+ function = "can1";
+ groups = "can1_6_grp";
+ };
+
+ conf {
+ groups = "can1_6_grp";
+ slew-rate = <SLEW_RATE_SLOW>;
+ io-standard = <IO_STANDARD_LVCMOS18>;
+ drive-strength = <12>;
+ };
+
+ conf-rx {
+ pins = "MIO25";
+ bias-high-impedance;
+ };
+
+ conf-tx {
+ pins = "MIO24";
+ bias-disable;
+ };
+ };
+
+ pinctrl_i2c1_default: i2c1-default {
+ mux {
+ groups = "i2c1_4_grp";
+ function = "i2c1";
+ };
+
+ conf {
+ groups = "i2c1_4_grp";
+ bias-pull-up;
+ slew-rate = <SLEW_RATE_SLOW>;
+ io-standard = <IO_STANDARD_LVCMOS18>;
+ drive-strength = <12>;
+ };
+ };
+
+ pinctrl_i2c1_gpio: i2c1-gpio {
+ mux {
+ groups = "gpio0_16_grp", "gpio0_17_grp";
+ function = "gpio0";
+ };
+
+ conf {
+ groups = "gpio0_16_grp", "gpio0_17_grp";
+ slew-rate = <SLEW_RATE_SLOW>;
+ io-standard = <IO_STANDARD_LVCMOS18>;
+ drive-strength = <12>;
+ };
+ };
+
+ pinctrl_gem3_default: gem3-default {
+ mux {
+ function = "ethernet3";
+ groups = "ethernet3_0_grp";
+ };
+
+ conf {
+ groups = "ethernet3_0_grp";
+ slew-rate = <SLEW_RATE_SLOW>;
+ io-standard = <IO_STANDARD_LVCMOS18>;
+ drive-strength = <12>;
+ };
+
+ conf-rx {
+ pins = "MIO70", "MIO71", "MIO72", "MIO73", "MIO74",
+ "MIO75";
+ bias-high-impedance;
+ low-power-disable;
+ };
+
+ conf-tx {
+ pins = "MIO64", "MIO65", "MIO66", "MIO67", "MIO68",
+ "MIO69";
+ bias-disable;
+ low-power-enable;
+ };
+
+ mux-mdio {
+ function = "mdio3";
+ groups = "mdio3_0_grp";
+ };
+
+ conf-mdio {
+ groups = "mdio3_0_grp";
+ slew-rate = <SLEW_RATE_SLOW>;
+ io-standard = <IO_STANDARD_LVCMOS18>;
+ bias-disable;
+ };
+ };
+
+ pinctrl_sdhci1_default: sdhci1-default {
+ mux {
+ groups = "sdio1_0_grp";
+ function = "sdio1";
+ };
+
+ conf {
+ groups = "sdio1_0_grp";
+ slew-rate = <SLEW_RATE_SLOW>;
+ io-standard = <IO_STANDARD_LVCMOS18>;
+ bias-disable;
+ drive-strength = <12>;
+ };
+
+ mux-cd {
+ groups = "sdio1_cd_0_grp";
+ function = "sdio1_cd";
+ };
+
+ conf-cd {
+ groups = "sdio1_cd_0_grp";
+ bias-high-impedance;
+ bias-pull-up;
+ slew-rate = <SLEW_RATE_SLOW>;
+ io-standard = <IO_STANDARD_LVCMOS18>;
+ };
+ };
+
+ pinctrl_uart0_default: uart0-default {
+ mux {
+ groups = "uart0_4_grp";
+ function = "uart0";
+ };
+
+ conf {
+ groups = "uart0_4_grp";
+ slew-rate = <SLEW_RATE_SLOW>;
+ io-standard = <IO_STANDARD_LVCMOS18>;
+ drive-strength = <12>;
+ };
+
+ conf-rx {
+ pins = "MIO18";
+ bias-high-impedance;
+ };
+
+ conf-tx {
+ pins = "MIO19";
+ bias-disable;
+ };
+ };
+
+ pinctrl_uart1_default: uart1-default {
+ mux {
+ groups = "uart1_5_grp";
+ function = "uart1";
+ };
+
+ conf {
+ groups = "uart1_5_grp";
+ slew-rate = <SLEW_RATE_SLOW>;
+ io-standard = <IO_STANDARD_LVCMOS18>;
+ drive-strength = <12>;
+ };
+
+ conf-rx {
+ pins = "MIO21";
+ bias-high-impedance;
+ };
+
+ conf-tx {
+ pins = "MIO20";
+ bias-disable;
+ };
+ };
+
+ pinctrl_usb0_default: usb0-default {
+ mux {
+ groups = "usb0_0_grp";
+ function = "usb0";
+ };
+
+ conf {
+ groups = "usb0_0_grp";
+ slew-rate = <SLEW_RATE_SLOW>;
+ io-standard = <IO_STANDARD_LVCMOS18>;
+ drive-strength = <12>;
+ };
+
+ conf-rx {
+ pins = "MIO52", "MIO53", "MIO55";
+ bias-high-impedance;
+ };
+
+ conf-tx {
+ pins = "MIO54", "MIO56", "MIO57", "MIO58", "MIO59",
+ "MIO60", "MIO61", "MIO62", "MIO63";
+ bias-disable;
+ };
+ };
+};
+
+&qspi {
+ status = "okay";
+ flash@0 {
+ compatible = "m25p80", "spi-flash"; /* n25q512a 128MiB */
+ #address-cells = <1>;
+ #size-cells = <1>;
+ reg = <0x0>;
+ spi-tx-bus-width = <1>;
+ spi-rx-bus-width = <4>;
+ spi-max-frequency = <108000000>; /* Based on DC1 spec */
+ partition@qspi-fsbl-uboot { /* for testing purpose */
+ label = "qspi-fsbl-uboot";
+ reg = <0x0 0x100000>;
+ };
+ partition@qspi-linux { /* for testing purpose */
+ label = "qspi-linux";
+ reg = <0x100000 0x500000>;
+ };
+ partition@qspi-device-tree { /* for testing purpose */
+ label = "qspi-device-tree";
+ reg = <0x600000 0x20000>;
+ };
+ partition@qspi-rootfs { /* for testing purpose */
+ label = "qspi-rootfs";
+ reg = <0x620000 0x5E0000>;
+ };
+ };
+};
+
+&rtc {
+ status = "okay";
+};
+
+&sata {
+ status = "okay";
+ /* SATA OOB timing settings */
+ ceva,p0-cominit-params = /bits/ 8 <0x18 0x40 0x18 0x28>;
+ ceva,p0-comwake-params = /bits/ 8 <0x06 0x14 0x08 0x0E>;
+ ceva,p0-burst-params = /bits/ 8 <0x13 0x08 0x4A 0x06>;
+ ceva,p0-retry-params = /bits/ 16 <0x96A4 0x3FFC>;
+ ceva,p1-cominit-params = /bits/ 8 <0x18 0x40 0x18 0x28>;
+ ceva,p1-comwake-params = /bits/ 8 <0x06 0x14 0x08 0x0E>;
+ ceva,p1-burst-params = /bits/ 8 <0x13 0x08 0x4A 0x06>;
+ ceva,p1-retry-params = /bits/ 16 <0x96A4 0x3FFC>;
+ phy-names = "sata-phy";
+ phys = <&lane3 PHY_TYPE_SATA 1 1 125000000>;
+};
+
+/* SD1 with level shifter */
+&sdhci1 {
+ status = "okay";
+ no-1-8-v;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_sdhci1_default>;
+ xlnx,mio_bank = <1>;
+ disable-wp;
+};
+
+&serdes {
+ status = "okay";
+};
+
+&uart0 {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart0_default>;
+};
+
+&uart1 {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart1_default>;
+};
+
+/* ULPI SMSC USB3320 */
+&usb0 {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usb0_default>;
+};
+
+&dwc3_0 {
+ status = "okay";
+ dr_mode = "host";
+ snps,usb3_lpm_capable;
+ phy-names = "usb3-phy";
+ phys = <&lane2 PHY_TYPE_USB3 0 2 26000000>;
+ maximum-speed = "super-speed";
+};
+
+&watchdog0 {
+ status = "okay";
+};
+
+&xilinx_ams {
+ status = "okay";
+};
+
+&ams_ps {
+ status = "okay";
+};
+
+&ams_pl {
+ status = "okay";
+};
+
+&zynqmp_dpsub {
+ status = "okay";
+ phy-names = "dp-phy0", "dp-phy1";
+ phys = <&lane1 PHY_TYPE_DP 0 3 27000000>, <&lane0 PHY_TYPE_DP 1 3 27000000>;
+};
+
+&zynqmp_dp_snd_pcm0 {
+ status = "okay";
+};
+
+&zynqmp_dp_snd_pcm1 {
+ status = "okay";
+};
+
+&zynqmp_dp_snd_card0 {
+ status = "okay";
+};
+
+&zynqmp_dp_snd_codec0 {
+ status = "okay";
+};
+
+&xlnx_dpdma {
+ status = "okay";
+};
/dts-v1/;
#include "zynqmp.dtsi"
-#include "zynqmp-clk.dtsi"
+#include "zynqmp-clk-ccf.dtsi"
#include <dt-bindings/input/input.h>
#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/pinctrl/pinctrl-zynqmp.h>
+#include <dt-bindings/phy/phy.h>
/ {
model = "ZynqMP ZCU106 RevA";
aliases {
ethernet0 = &gem3;
+ gpio0 = &gpio;
i2c0 = &i2c0;
i2c1 = &i2c1;
mmc0 = &sdhci1;
serial0 = &uart0;
serial1 = &uart1;
serial2 = &dcc;
+ spi0 = &qspi;
+ usb0 = &usb0;
};
chosen {
bootargs = "earlycon";
stdout-path = "serial0:115200n8";
+ xlnx,eeprom = &eeprom;
};
memory@0 {
label = "sw19";
gpios = <&gpio 22 GPIO_ACTIVE_HIGH>;
linux,code = <KEY_DOWN>;
- wakeup-source;
+ gpio-key,wakeup;
autorepeat;
};
};
leds {
compatible = "gpio-leds";
- heartbeat-led {
+ heartbeat_led {
label = "heartbeat";
gpios = <&gpio 23 GPIO_ACTIVE_HIGH>;
linux,default-trigger = "heartbeat";
&can1 {
status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_can1_default>;
};
&dcc {
status = "okay";
};
-/* fpd_dma clk 667MHz, lpd_dma 500MHz */
&fpd_dma_chan1 {
status = "okay";
};
status = "okay";
phy-handle = <&phy0>;
phy-mode = "rgmii-id";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_gem3_default>;
phy0: phy@c {
reg = <0xc>;
ti,rx-internal-delay = <0x8>;
ti,tx-internal-delay = <0xa>;
ti,fifo-depth = <0x1>;
+ ti,dp83867-rxctrl-strap-quirk;
};
};
&gpio {
status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_gpio_default>;
+};
+
+&gpu {
+ status = "okay";
};
&i2c0 {
status = "okay";
clock-frequency = <400000>;
+ pinctrl-names = "default", "gpio";
+ pinctrl-0 = <&pinctrl_i2c0_default>;
+ pinctrl-1 = <&pinctrl_i2c0_gpio>;
+ scl-gpios = <&gpio 14 GPIO_ACTIVE_HIGH>;
+ sda-gpios = <&gpio 15 GPIO_ACTIVE_HIGH>;
tca6416_u97: gpio@20 {
compatible = "ti,tca6416";
&i2c1 {
status = "okay";
clock-frequency = <400000>;
+ pinctrl-names = "default", "gpio";
+ pinctrl-0 = <&pinctrl_i2c1_default>;
+ pinctrl-1 = <&pinctrl_i2c1_gpio>;
+ scl-gpios = <&gpio 16 GPIO_ACTIVE_HIGH>;
+ sda-gpios = <&gpio 17 GPIO_ACTIVE_HIGH>;
/* PL i2c via PCA9306 - u45 */
i2c-mux@74 { /* u34 */
#size-cells = <0>;
reg = <1>;
si5341: clock-generator@36 { /* SI5341 - u69 */
+ compatible = "si5341";
reg = <0x36>;
};
temperature-stability = <50>;
factory-fout = <300000000>;
clock-frequency = <300000000>;
+ clock-output-names = "si570_user";
};
};
i2c@3 {
temperature-stability = <50>; /* copy from zc702 */
factory-fout = <156250000>;
clock-frequency = <148500000>;
+ clock-output-names = "si570_mgt";
};
};
i2c@4 {
#size-cells = <0>;
reg = <4>;
si5328: clock-generator@69 {/* SI5328 - u20 */
+ compatible = "silabs,si5328";
reg = <0x69>;
};
};
};
};
+&pinctrl0 {
+ status = "okay";
+ pinctrl_i2c0_default: i2c0-default {
+ mux {
+ groups = "i2c0_3_grp";
+ function = "i2c0";
+ };
+
+ conf {
+ groups = "i2c0_3_grp";
+ bias-pull-up;
+ slew-rate = <SLEW_RATE_SLOW>;
+ io-standard = <IO_STANDARD_LVCMOS18>;
+ };
+ };
+
+ pinctrl_i2c0_gpio: i2c0-gpio {
+ mux {
+ groups = "gpio0_14_grp", "gpio0_15_grp";
+ function = "gpio0";
+ };
+
+ conf {
+ groups = "gpio0_14_grp", "gpio0_15_grp";
+ slew-rate = <SLEW_RATE_SLOW>;
+ io-standard = <IO_STANDARD_LVCMOS18>;
+ };
+ };
+
+ pinctrl_i2c1_default: i2c1-default {
+ mux {
+ groups = "i2c1_4_grp";
+ function = "i2c1";
+ };
+
+ conf {
+ groups = "i2c1_4_grp";
+ bias-pull-up;
+ slew-rate = <SLEW_RATE_SLOW>;
+ io-standard = <IO_STANDARD_LVCMOS18>;
+ };
+ };
+
+ pinctrl_i2c1_gpio: i2c1-gpio {
+ mux {
+ groups = "gpio0_16_grp", "gpio0_17_grp";
+ function = "gpio0";
+ };
+
+ conf {
+ groups = "gpio0_16_grp", "gpio0_17_grp";
+ slew-rate = <SLEW_RATE_SLOW>;
+ io-standard = <IO_STANDARD_LVCMOS18>;
+ };
+ };
+
+ pinctrl_uart0_default: uart0-default {
+ mux {
+ groups = "uart0_4_grp";
+ function = "uart0";
+ };
+
+ conf {
+ groups = "uart0_4_grp";
+ slew-rate = <SLEW_RATE_SLOW>;
+ io-standard = <IO_STANDARD_LVCMOS18>;
+ };
+
+ conf-rx {
+ pins = "MIO18";
+ bias-high-impedance;
+ };
+
+ conf-tx {
+ pins = "MIO19";
+ bias-disable;
+ };
+ };
+
+ pinctrl_uart1_default: uart1-default {
+ mux {
+ groups = "uart1_5_grp";
+ function = "uart1";
+ };
+
+ conf {
+ groups = "uart1_5_grp";
+ slew-rate = <SLEW_RATE_SLOW>;
+ io-standard = <IO_STANDARD_LVCMOS18>;
+ };
+
+ conf-rx {
+ pins = "MIO21";
+ bias-high-impedance;
+ };
+
+ conf-tx {
+ pins = "MIO20";
+ bias-disable;
+ };
+ };
+
+ pinctrl_usb0_default: usb0-default {
+ mux {
+ groups = "usb0_0_grp";
+ function = "usb0";
+ };
+
+ conf {
+ groups = "usb0_0_grp";
+ slew-rate = <SLEW_RATE_SLOW>;
+ io-standard = <IO_STANDARD_LVCMOS18>;
+ };
+
+ conf-rx {
+ pins = "MIO52", "MIO53", "MIO55";
+ bias-high-impedance;
+ };
+
+ conf-tx {
+ pins = "MIO54", "MIO56", "MIO57", "MIO58", "MIO59",
+ "MIO60", "MIO61", "MIO62", "MIO63";
+ bias-disable;
+ };
+ };
+
+ pinctrl_gem3_default: gem3-default {
+ mux {
+ function = "ethernet3";
+ groups = "ethernet3_0_grp";
+ };
+
+ conf {
+ groups = "ethernet3_0_grp";
+ slew-rate = <SLEW_RATE_SLOW>;
+ io-standard = <IO_STANDARD_LVCMOS18>;
+ };
+
+ conf-rx {
+ pins = "MIO70", "MIO71", "MIO72", "MIO73", "MIO74",
+ "MIO75";
+ bias-high-impedance;
+ low-power-disable;
+ };
+
+ conf-tx {
+ pins = "MIO64", "MIO65", "MIO66", "MIO67", "MIO68",
+ "MIO69";
+ bias-disable;
+ low-power-enable;
+ };
+
+ mux-mdio {
+ function = "mdio3";
+ groups = "mdio3_0_grp";
+ };
+
+ conf-mdio {
+ groups = "mdio3_0_grp";
+ slew-rate = <SLEW_RATE_SLOW>;
+ io-standard = <IO_STANDARD_LVCMOS18>;
+ bias-disable;
+ };
+ };
+
+ pinctrl_can1_default: can1-default {
+ mux {
+ function = "can1";
+ groups = "can1_6_grp";
+ };
+
+ conf {
+ groups = "can1_6_grp";
+ slew-rate = <SLEW_RATE_SLOW>;
+ io-standard = <IO_STANDARD_LVCMOS18>;
+ };
+
+ conf-rx {
+ pins = "MIO25";
+ bias-high-impedance;
+ };
+
+ conf-tx {
+ pins = "MIO24";
+ bias-disable;
+ };
+ };
+
+ pinctrl_sdhci1_default: sdhci1-default {
+ mux {
+ groups = "sdio1_0_grp";
+ function = "sdio1";
+ };
+
+ conf {
+ groups = "sdio1_0_grp";
+ slew-rate = <SLEW_RATE_SLOW>;
+ io-standard = <IO_STANDARD_LVCMOS18>;
+ bias-disable;
+ };
+
+ mux-cd {
+ groups = "sdio1_cd_0_grp";
+ function = "sdio1_cd";
+ };
+
+ conf-cd {
+ groups = "sdio1_cd_0_grp";
+ bias-high-impedance;
+ bias-pull-up;
+ slew-rate = <SLEW_RATE_SLOW>;
+ io-standard = <IO_STANDARD_LVCMOS18>;
+ };
+
+ mux-wp {
+ groups = "sdio1_wp_0_grp";
+ function = "sdio1_wp";
+ };
+
+ conf-wp {
+ groups = "sdio1_wp_0_grp";
+ bias-high-impedance;
+ bias-pull-up;
+ slew-rate = <SLEW_RATE_SLOW>;
+ io-standard = <IO_STANDARD_LVCMOS18>;
+ };
+ };
+
+ pinctrl_gpio_default: gpio-default {
+ mux {
+ function = "gpio0";
+ groups = "gpio0_22_grp", "gpio0_23_grp";
+ };
+
+ conf {
+ groups = "gpio0_22_grp", "gpio0_23_grp";
+ slew-rate = <SLEW_RATE_SLOW>;
+ io-standard = <IO_STANDARD_LVCMOS18>;
+ };
+
+ mux-msp {
+ function = "gpio0";
+ groups = "gpio0_13_grp", "gpio0_38_grp";
+ };
+
+ conf-msp {
+ groups = "gpio0_13_grp", "gpio0_38_grp";
+ slew-rate = <SLEW_RATE_SLOW>;
+ io-standard = <IO_STANDARD_LVCMOS18>;
+ };
+
+ conf-pull-up {
+ pins = "MIO22";
+ bias-pull-up;
+ };
+
+ conf-pull-none {
+ pins = "MIO13", "MIO23", "MIO38";
+ bias-disable;
+ };
+ };
+};
+
+&qspi {
+ status = "okay";
+ is-dual = <1>;
+ flash@0 {
+ compatible = "m25p80", "spi-flash"; /* 32MB */
+ #address-cells = <1>;
+ #size-cells = <1>;
+ reg = <0x0>;
+ spi-tx-bus-width = <1>;
+ spi-rx-bus-width = <4>; /* FIXME also DUAL configuration possible */
+ spi-max-frequency = <108000000>; /* Based on DC1 spec */
+ partition@qspi-fsbl-uboot { /* for testing purpose */
+ label = "qspi-fsbl-uboot";
+ reg = <0x0 0x100000>;
+ };
+ partition@qspi-linux { /* for testing purpose */
+ label = "qspi-linux";
+ reg = <0x100000 0x500000>;
+ };
+ partition@qspi-device-tree { /* for testing purpose */
+ label = "qspi-device-tree";
+ reg = <0x600000 0x20000>;
+ };
+ partition@qspi-rootfs { /* for testing purpose */
+ label = "qspi-rootfs";
+ reg = <0x620000 0x5E0000>;
+ };
+ };
+};
+
&rtc {
status = "okay";
};
ceva,p1-comwake-params = /bits/ 8 <0x06 0x14 0x08 0x0E>;
ceva,p1-burst-params = /bits/ 8 <0x13 0x08 0x4A 0x06>;
ceva,p1-retry-params = /bits/ 16 <0x96A4 0x3FFC>;
+ phy-names = "sata-phy";
+ phys = <&lane3 PHY_TYPE_SATA 1 1 125000000>;
};
/* SD1 with level shifter */
&sdhci1 {
status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_sdhci1_default>;
no-1-8-v;
+ xlnx,mio_bank = <1>;
+};
+
+&serdes {
+ status = "okay";
};
&uart0 {
status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart0_default>;
};
&uart1 {
status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart1_default>;
};
/* ULPI SMSC USB3320 */
&usb0 {
status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usb0_default>;
+};
+
+&dwc3_0 {
+ status = "okay";
+ dr_mode = "host";
+ snps,usb3_lpm_capable;
+ phy-names = "usb3-phy";
+ phys = <&lane2 PHY_TYPE_USB3 0 2 26000000>;
};
&watchdog0 {
status = "okay";
};
+
+&zynqmp_dpsub {
+ status = "okay";
+ phy-names = "dp-phy0", "dp-phy1";
+ phys = <&lane1 PHY_TYPE_DP 0 3 27000000>, <&lane0 PHY_TYPE_DP 1 3 27000000>;
+};
+
+&zynqmp_dp_snd_pcm0 {
+ status = "okay";
+};
+
+&zynqmp_dp_snd_pcm1 {
+ status = "okay";
+};
+
+&zynqmp_dp_snd_card0 {
+ status = "okay";
+};
+
+&zynqmp_dp_snd_codec0 {
+ status = "okay";
+};
+
+&xlnx_dpdma {
+ status = "okay";
+};
/dts-v1/;
#include "zynqmp.dtsi"
-#include "zynqmp-clk.dtsi"
+#include "zynqmp-clk-ccf.dtsi"
#include <dt-bindings/input/input.h>
#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/pinctrl/pinctrl-zynqmp.h>
+#include <dt-bindings/phy/phy.h>
/ {
model = "ZynqMP ZCU111 RevA";
aliases {
ethernet0 = &gem3;
+ gpio0 = &gpio;
i2c0 = &i2c0;
i2c1 = &i2c1;
mmc0 = &sdhci1;
rtc0 = &rtc;
serial0 = &uart0;
serial1 = &dcc;
+ spi0 = &qspi;
+ usb0 = &usb0;
};
chosen {
bootargs = "earlycon";
stdout-path = "serial0:115200n8";
+ xlnx,eeprom = &eeprom;
};
memory@0 {
label = "sw19";
gpios = <&gpio 22 GPIO_ACTIVE_HIGH>;
linux,code = <KEY_DOWN>;
- wakeup-source;
+ gpio-key,wakeup;
autorepeat;
};
};
leds {
compatible = "gpio-leds";
- heartbeat-led {
+ heartbeat_led {
label = "heartbeat";
gpios = <&gpio 23 GPIO_ACTIVE_HIGH>;
linux,default-trigger = "heartbeat";
status = "okay";
phy-handle = <&phy0>;
phy-mode = "rgmii-id";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_gem3_default>;
phy0: phy@c {
reg = <0xc>;
ti,rx-internal-delay = <0x8>;
ti,tx-internal-delay = <0xa>;
ti,fifo-depth = <0x1>;
+ ti,dp83867-rxctrl-strap-quirk;
};
};
&gpio {
status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_gpio_default>;
+};
+
+&gpu {
+ status = "okay";
};
&i2c0 {
status = "okay";
clock-frequency = <400000>;
+ pinctrl-names = "default", "gpio";
+ pinctrl-0 = <&pinctrl_i2c0_default>;
+ pinctrl-1 = <&pinctrl_i2c0_gpio>;
+ scl-gpios = <&gpio 14 GPIO_ACTIVE_HIGH>;
+ sda-gpios = <&gpio 15 GPIO_ACTIVE_HIGH>;
tca6416_u22: gpio@20 {
compatible = "ti,tca6416";
#size-cells = <0>;
reg = <2>;
irps5401_43: irps54012@43 { /* IRPS5401 - u53 check these */
+ #clock-cells = <0>;
+ compatible = "infineon,irps5401";
reg = <0x43>;
};
irps5401_44: irps54012@44 { /* IRPS5401 - u55 */
+ #clock-cells = <0>;
+ compatible = "infineon,irps5401";
reg = <0x44>;
};
irps5401_45: irps54012@45 { /* IRPS5401 - u57 */
+ #clock-cells = <0>;
+ compatible = "infineon,irps5401";
reg = <0x45>;
};
/* u68 IR38064 +0 */
&i2c1 {
status = "okay";
clock-frequency = <400000>;
+ pinctrl-names = "default", "gpio";
+ pinctrl-0 = <&pinctrl_i2c1_default>;
+ pinctrl-1 = <&pinctrl_i2c1_gpio>;
+ scl-gpios = <&gpio 16 GPIO_ACTIVE_HIGH>;
+ sda-gpios = <&gpio 17 GPIO_ACTIVE_HIGH>;
i2c-mux@74 { /* u26 */
compatible = "nxp,pca9548";
#size-cells = <0>;
reg = <1>;
si5341: clock-generator@36 { /* SI5341 - u46 */
+ compatible = "si5341";
reg = <0x36>;
};
temperature-stability = <50>;
factory-fout = <300000000>;
clock-frequency = <300000000>;
+ clock-output-names = "si570_user";
};
};
i2c@3 {
temperature-stability = <50>;
factory-fout = <156250000>;
clock-frequency = <148500000>;
+ clock-output-names = "si570_mgt";
};
};
i2c@4 {
#size-cells = <0>;
reg = <4>;
si5328: clock-generator@69 { /* SI5328 - u48 */
+ compatible = "silabs,si5328";
reg = <0x69>;
};
};
};
};
+&pinctrl0 {
+ status = "okay";
+ pinctrl_i2c0_default: i2c0-default {
+ mux {
+ groups = "i2c0_3_grp";
+ function = "i2c0";
+ };
+
+ conf {
+ groups = "i2c0_3_grp";
+ bias-pull-up;
+ slew-rate = <SLEW_RATE_SLOW>;
+ io-standard = <IO_STANDARD_LVCMOS18>;
+ };
+ };
+
+ pinctrl_i2c0_gpio: i2c0-gpio {
+ mux {
+ groups = "gpio0_14_grp", "gpio0_15_grp";
+ function = "gpio0";
+ };
+
+ conf {
+ groups = "gpio0_14_grp", "gpio0_15_grp";
+ slew-rate = <SLEW_RATE_SLOW>;
+ io-standard = <IO_STANDARD_LVCMOS18>;
+ };
+ };
+
+ pinctrl_i2c1_default: i2c1-default {
+ mux {
+ groups = "i2c1_4_grp";
+ function = "i2c1";
+ };
+
+ conf {
+ groups = "i2c1_4_grp";
+ bias-pull-up;
+ slew-rate = <SLEW_RATE_SLOW>;
+ io-standard = <IO_STANDARD_LVCMOS18>;
+ };
+ };
+
+ pinctrl_i2c1_gpio: i2c1-gpio {
+ mux {
+ groups = "gpio0_16_grp", "gpio0_17_grp";
+ function = "gpio0";
+ };
+
+ conf {
+ groups = "gpio0_16_grp", "gpio0_17_grp";
+ slew-rate = <SLEW_RATE_SLOW>;
+ io-standard = <IO_STANDARD_LVCMOS18>;
+ };
+ };
+
+ pinctrl_uart0_default: uart0-default {
+ mux {
+ groups = "uart0_4_grp";
+ function = "uart0";
+ };
+
+ conf {
+ groups = "uart0_4_grp";
+ slew-rate = <SLEW_RATE_SLOW>;
+ io-standard = <IO_STANDARD_LVCMOS18>;
+ };
+
+ conf-rx {
+ pins = "MIO18";
+ bias-high-impedance;
+ };
+
+ conf-tx {
+ pins = "MIO19";
+ bias-disable;
+ };
+ };
+
+ pinctrl_usb0_default: usb0-default {
+ mux {
+ groups = "usb0_0_grp";
+ function = "usb0";
+ };
+
+ conf {
+ groups = "usb0_0_grp";
+ slew-rate = <SLEW_RATE_SLOW>;
+ io-standard = <IO_STANDARD_LVCMOS18>;
+ };
+
+ conf-rx {
+ pins = "MIO52", "MIO53", "MIO55";
+ bias-high-impedance;
+ };
+
+ conf-tx {
+ pins = "MIO54", "MIO56", "MIO57", "MIO58", "MIO59",
+ "MIO60", "MIO61", "MIO62", "MIO63";
+ bias-disable;
+ };
+ };
+
+ pinctrl_gem3_default: gem3-default {
+ mux {
+ function = "ethernet3";
+ groups = "ethernet3_0_grp";
+ };
+
+ conf {
+ groups = "ethernet3_0_grp";
+ slew-rate = <SLEW_RATE_SLOW>;
+ io-standard = <IO_STANDARD_LVCMOS18>;
+ };
+
+ conf-rx {
+ pins = "MIO70", "MIO71", "MIO72", "MIO73", "MIO74",
+ "MIO75";
+ bias-high-impedance;
+ low-power-disable;
+ };
+
+ conf-tx {
+ pins = "MIO64", "MIO65", "MIO66", "MIO67", "MIO68",
+ "MIO69";
+ bias-disable;
+ low-power-enable;
+ };
+
+ mux-mdio {
+ function = "mdio3";
+ groups = "mdio3_0_grp";
+ };
+
+ conf-mdio {
+ groups = "mdio3_0_grp";
+ slew-rate = <SLEW_RATE_SLOW>;
+ io-standard = <IO_STANDARD_LVCMOS18>;
+ bias-disable;
+ };
+ };
+
+ pinctrl_sdhci1_default: sdhci1-default {
+ mux {
+ groups = "sdio1_0_grp";
+ function = "sdio1";
+ };
+
+ conf {
+ groups = "sdio1_0_grp";
+ slew-rate = <SLEW_RATE_SLOW>;
+ io-standard = <IO_STANDARD_LVCMOS18>;
+ bias-disable;
+ };
+
+ mux-cd {
+ groups = "sdio1_cd_0_grp";
+ function = "sdio1_cd";
+ };
+
+ conf-cd {
+ groups = "sdio1_cd_0_grp";
+ bias-high-impedance;
+ bias-pull-up;
+ slew-rate = <SLEW_RATE_SLOW>;
+ io-standard = <IO_STANDARD_LVCMOS18>;
+ };
+ };
+
+ pinctrl_gpio_default: gpio-default {
+ mux {
+ function = "gpio0";
+ groups = "gpio0_22_grp", "gpio0_23_grp";
+ };
+
+ conf {
+ groups = "gpio0_22_grp", "gpio0_23_grp";
+ slew-rate = <SLEW_RATE_SLOW>;
+ io-standard = <IO_STANDARD_LVCMOS18>;
+ };
+
+ mux-msp {
+ function = "gpio0";
+ groups = "gpio0_13_grp", "gpio0_38_grp";
+ };
+
+ conf-msp {
+ groups = "gpio0_13_grp", "gpio0_38_grp";
+ slew-rate = <SLEW_RATE_SLOW>;
+ io-standard = <IO_STANDARD_LVCMOS18>;
+ };
+
+ conf-pull-up {
+ pins = "MIO22";
+ bias-pull-up;
+ };
+
+ conf-pull-none {
+ pins = "MIO13", "MIO23", "MIO38";
+ bias-disable;
+ };
+ };
+};
+
+&qspi {
+ status = "okay";
+ is-dual = <1>;
+ flash@0 {
+ compatible = "m25p80", "spi-flash"; /* 32MB */
+ #address-cells = <1>;
+ #size-cells = <1>;
+ reg = <0x0>;
+ spi-tx-bus-width = <1>;
+ spi-rx-bus-width = <4>; /* FIXME also DUAL configuration possible */
+ spi-max-frequency = <108000000>; /* Based on DC1 spec */
+ partition@qspi-fsbl-uboot { /* for testing purpose */
+ label = "qspi-fsbl-uboot";
+ reg = <0x0 0x100000>;
+ };
+ partition@qspi-linux { /* for testing purpose */
+ label = "qspi-linux";
+ reg = <0x100000 0x500000>;
+ };
+ partition@qspi-device-tree { /* for testing purpose */
+ label = "qspi-device-tree";
+ reg = <0x600000 0x20000>;
+ };
+ partition@qspi-rootfs { /* for testing purpose */
+ label = "qspi-rootfs";
+ reg = <0x620000 0x5E0000>;
+ };
+ };
+};
+
&rtc {
status = "okay";
};
ceva,p1-comwake-params = /bits/ 8 <0x06 0x14 0x08 0x0E>;
ceva,p1-burst-params = /bits/ 8 <0x13 0x08 0x4A 0x06>;
ceva,p1-retry-params = /bits/ 16 <0x96A4 0x3FFC>;
+ phy-names = "sata-phy";
+ phys = <&lane3 PHY_TYPE_SATA 1 3 125000000>;
};
/* SD1 with level shifter */
&sdhci1 {
status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_sdhci1_default>;
no-1-8-v;
+ disable-wp;
+ xlnx,mio_bank = <1>;
+};
+
+&serdes {
+ status = "okay";
};
&uart0 {
status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart0_default>;
};
/* ULPI SMSC USB3320 */
&usb0 {
status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usb0_default>;
+};
+
+&dwc3_0 {
+ status = "okay";
+ dr_mode = "host";
+ snps,usb3_lpm_capable;
+ phy-names = "usb3-phy";
+ phys = <&lane2 PHY_TYPE_USB3 0 2 26000000>;
+};
+
+&zynqmp_dpsub {
+ status = "okay";
+ phy-names = "dp-phy0", "dp-phy1";
+ phys = <&lane1 PHY_TYPE_DP 0 1 27000000>, <&lane0 PHY_TYPE_DP 1 1 27000000>;
+};
+
+&zynqmp_dp_snd_pcm0 {
+ status = "okay";
+};
+
+&zynqmp_dp_snd_pcm1 {
+ status = "okay";
+};
+
+&zynqmp_dp_snd_card0 {
+ status = "okay";
+};
+
+&zynqmp_dp_snd_codec0 {
+ status = "okay";
+};
+
+&xlnx_dpdma {
+ status = "okay";
};
* the License, or (at your option) any later version.
*/
+#include <dt-bindings/power/xlnx-zynqmp-power.h>
+#include <dt-bindings/reset/xlnx-zynqmp-resets.h>
+
/ {
compatible = "xlnx,zynqmp";
#address-cells = <2>;
};
};
- cpu_opp_table: cpu-opp-table {
+ cpu_opp_table: cpu_opp_table {
compatible = "operating-points-v2";
opp-shared;
opp00 {
dcc: dcc {
compatible = "arm,dcc";
status = "disabled";
+ u-boot,dm-pre-reloc;
+ };
+
+ zynqmp_ipi {
+ compatible = "xlnx,zynqmp-ipi-mailbox";
+ interrupt-parent = <&gic>;
+ interrupts = <0 35 4>;
+ xlnx,ipi-id = <0>;
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+
+ ipi_mailbox_pmu1: mailbox@ff990400 {
+ reg = <0x0 0xff9905c0 0x0 0x20>,
+ <0x0 0xff9905e0 0x0 0x20>,
+ <0x0 0xff990e80 0x0 0x20>,
+ <0x0 0xff990ea0 0x0 0x20>;
+ reg-names = "local_request_region", "local_response_region",
+ "remote_request_region", "remote_response_region";
+ #mbox-cells = <1>;
+ xlnx,ipi-id = <4>;
+ };
};
pmu {
method = "smc";
};
+ firmware {
+ zynqmp_firmware: zynqmp-firmware {
+ compatible = "xlnx,zynqmp-firmware";
+ method = "smc";
+ #power-domain-cells = <0x1>;
+ u-boot,dm-pre-reloc;
+
+ zynqmp_power: zynqmp-power {
+ compatible = "xlnx,zynqmp-power";
+ interrupt-parent = <&gic>;
+ interrupts = <0 35 4>;
+ mboxes = <&ipi_mailbox_pmu1 0>,
+ <&ipi_mailbox_pmu1 1>;
+ mbox-names = "tx", "rx";
+ };
+
+ zynqmp_reset: reset-controller {
+ compatible = "xlnx,zynqmp-reset";
+ #reset-cells = <1>;
+ };
+
+ pinctrl0: pinctrl {
+ compatible = "xlnx,zynqmp-pinctrl";
+ status = "disabled";
+ };
+ };
+ };
+
timer {
compatible = "arm,armv8-timer";
interrupt-parent = <&gic>;
<1 10 0xf08>;
};
- amba_apu: amba-apu@0 {
+ edac {
+ compatible = "arm,cortex-a53-edac";
+ };
+
+ fpga_full: fpga-full {
+ compatible = "fpga-region";
+ fpga-mgr = <&pcap>;
+ #address-cells = <2>;
+ #size-cells = <2>;
+ };
+
+ nvmem_firmware {
+ compatible = "xlnx,zynqmp-nvmem-fw";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ soc_revision: soc_revision@0 {
+ reg = <0x0 0x4>;
+ };
+ /* efuse access */
+ efuse_dna: efuse_dna@c {
+ reg = <0xc 0xc>;
+ };
+ efuse_usr0: efuse_usr0@20 {
+ reg = <0x20 0x4>;
+ };
+ efuse_usr1: efuse_usr1@24 {
+ reg = <0x24 0x4>;
+ };
+ efuse_usr2: efuse_usr2@28 {
+ reg = <0x28 0x4>;
+ };
+ efuse_usr3: efuse_usr3@2c {
+ reg = <0x2c 0x4>;
+ };
+ efuse_usr4: efuse_usr4@30 {
+ reg = <0x30 0x4>;
+ };
+ efuse_usr5: efuse_usr5@34 {
+ reg = <0x34 0x4>;
+ };
+ efuse_usr6: efuse_usr6@38 {
+ reg = <0x38 0x4>;
+ };
+ efuse_usr7: efuse_usr7@3c {
+ reg = <0x3c 0x4>;
+ };
+ efuse_miscusr: efuse_miscusr@40 {
+ reg = <0x40 0x4>;
+ };
+ efuse_chash: efuse_chash@50 {
+ reg = <0x50 0x4>;
+ };
+ efuse_pufmisc: efuse_pufmisc@54 {
+ reg = <0x54 0x4>;
+ };
+ efuse_sec: efuse_sec@58 {
+ reg = <0x58 0x4>;
+ };
+ efuse_spkid: efuse_spkid@5c {
+ reg = <0x5c 0x4>;
+ };
+ efuse_ppk0hash: efuse_ppk0hash@a0 {
+ reg = <0xa0 0x30>;
+ };
+ efuse_ppk1hash: efuse_ppk1hash@d0 {
+ reg = <0xd0 0x30>;
+ };
+ };
+
+ pcap: pcap {
+ compatible = "xlnx,zynqmp-pcap-fpga";
+ clock-names = "ref_clk";
+ };
+
+ xlnx_rsa: zynqmp_rsa {
+ compatible = "xlnx,zynqmp-rsa";
+ };
+
+ xlnx_keccak_384: sha384 {
+ compatible = "xlnx,zynqmp-keccak-384";
+ };
+
+ xlnx_aes: zynqmp_aes {
+ compatible = "xlnx,zynqmp-aes";
+ };
+
+ amba_apu: amba_apu@0 {
compatible = "simple-bus";
#address-cells = <2>;
#size-cells = <1>;
};
};
+ smmu: smmu@fd800000 {
+ compatible = "arm,mmu-500";
+ reg = <0x0 0xfd800000 0x0 0x20000>;
+ #iommu-cells = <1>;
+ status = "disabled";
+ #global-interrupts = <1>;
+ interrupt-parent = <&gic>;
+ interrupts = <0 155 4>,
+ <0 155 4>, <0 155 4>, <0 155 4>, <0 155 4>,
+ <0 155 4>, <0 155 4>, <0 155 4>, <0 155 4>,
+ <0 155 4>, <0 155 4>, <0 155 4>, <0 155 4>,
+ <0 155 4>, <0 155 4>, <0 155 4>, <0 155 4>;
+ };
+
amba: amba {
compatible = "simple-bus";
+ u-boot,dm-pre-reloc;
#address-cells = <2>;
#size-cells = <2>;
ranges;
interrupt-parent = <&gic>;
tx-fifo-depth = <0x40>;
rx-fifo-depth = <0x40>;
+ power-domains = <&zynqmp_firmware PD_CAN_0>;
};
can1: can@ff070000 {
interrupt-parent = <&gic>;
tx-fifo-depth = <0x40>;
rx-fifo-depth = <0x40>;
+ power-domains = <&zynqmp_firmware PD_CAN_1>;
};
cci: cci@fd6e0000 {
interrupts = <0 124 4>;
clock-names = "clk_main", "clk_apb";
xlnx,bus-width = <128>;
+ #stream-id-cells = <1>;
+ iommus = <&smmu 0x14e8>;
+ power-domains = <&zynqmp_firmware PD_GDMA>;
};
fpd_dma_chan2: dma@fd510000 {
interrupts = <0 125 4>;
clock-names = "clk_main", "clk_apb";
xlnx,bus-width = <128>;
+ #stream-id-cells = <1>;
+ iommus = <&smmu 0x14e9>;
+ power-domains = <&zynqmp_firmware PD_GDMA>;
};
fpd_dma_chan3: dma@fd520000 {
interrupts = <0 126 4>;
clock-names = "clk_main", "clk_apb";
xlnx,bus-width = <128>;
+ #stream-id-cells = <1>;
+ iommus = <&smmu 0x14ea>;
+ power-domains = <&zynqmp_firmware PD_GDMA>;
};
fpd_dma_chan4: dma@fd530000 {
interrupts = <0 127 4>;
clock-names = "clk_main", "clk_apb";
xlnx,bus-width = <128>;
+ #stream-id-cells = <1>;
+ iommus = <&smmu 0x14eb>;
+ power-domains = <&zynqmp_firmware PD_GDMA>;
};
fpd_dma_chan5: dma@fd540000 {
interrupts = <0 128 4>;
clock-names = "clk_main", "clk_apb";
xlnx,bus-width = <128>;
+ #stream-id-cells = <1>;
+ iommus = <&smmu 0x14ec>;
+ power-domains = <&zynqmp_firmware PD_GDMA>;
};
fpd_dma_chan6: dma@fd550000 {
interrupts = <0 129 4>;
clock-names = "clk_main", "clk_apb";
xlnx,bus-width = <128>;
+ #stream-id-cells = <1>;
+ iommus = <&smmu 0x14ed>;
+ power-domains = <&zynqmp_firmware PD_GDMA>;
};
fpd_dma_chan7: dma@fd560000 {
interrupts = <0 130 4>;
clock-names = "clk_main", "clk_apb";
xlnx,bus-width = <128>;
+ #stream-id-cells = <1>;
+ iommus = <&smmu 0x14ee>;
+ power-domains = <&zynqmp_firmware PD_GDMA>;
};
fpd_dma_chan8: dma@fd570000 {
interrupts = <0 131 4>;
clock-names = "clk_main", "clk_apb";
xlnx,bus-width = <128>;
+ #stream-id-cells = <1>;
+ iommus = <&smmu 0x14ef>;
+ power-domains = <&zynqmp_firmware PD_GDMA>;
+ };
+
+ gpu: gpu@fd4b0000 {
+ status = "disabled";
+ compatible = "arm,mali-400", "arm,mali-utgard";
+ reg = <0x0 0xfd4b0000 0x0 0x10000>;
+ interrupt-parent = <&gic>;
+ interrupts = <0 132 4>, <0 132 4>, <0 132 4>, <0 132 4>, <0 132 4>, <0 132 4>;
+ interrupt-names = "IRQGP", "IRQGPMMU", "IRQPP0", "IRQPPMMU0", "IRQPP1", "IRQPPMMU1";
+ clock-names = "gpu", "gpu_pp0", "gpu_pp1";
+ power-domains = <&zynqmp_firmware PD_GPU>;
};
/* LPDDMA default allows only secured access. inorder to enable
interrupts = <0 77 4>;
clock-names = "clk_main", "clk_apb";
xlnx,bus-width = <64>;
+ #stream-id-cells = <1>;
+ /* iommus = <&smmu 0x868>; */
+ power-domains = <&zynqmp_firmware PD_ADMA>;
};
lpd_dma_chan2: dma@ffa90000 {
interrupts = <0 78 4>;
clock-names = "clk_main", "clk_apb";
xlnx,bus-width = <64>;
+ #stream-id-cells = <1>;
+ /* iommus = <&smmu 0x869>; */
+ power-domains = <&zynqmp_firmware PD_ADMA>;
};
lpd_dma_chan3: dma@ffaa0000 {
interrupts = <0 79 4>;
clock-names = "clk_main", "clk_apb";
xlnx,bus-width = <64>;
+ #stream-id-cells = <1>;
+ /* iommus = <&smmu 0x86a>; */
+ power-domains = <&zynqmp_firmware PD_ADMA>;
};
lpd_dma_chan4: dma@ffab0000 {
interrupts = <0 80 4>;
clock-names = "clk_main", "clk_apb";
xlnx,bus-width = <64>;
+ #stream-id-cells = <1>;
+ /* iommus = <&smmu 0x86b>; */
+ power-domains = <&zynqmp_firmware PD_ADMA>;
};
lpd_dma_chan5: dma@ffac0000 {
interrupts = <0 81 4>;
clock-names = "clk_main", "clk_apb";
xlnx,bus-width = <64>;
+ #stream-id-cells = <1>;
+ /* iommus = <&smmu 0x86c>; */
+ power-domains = <&zynqmp_firmware PD_ADMA>;
};
lpd_dma_chan6: dma@ffad0000 {
interrupts = <0 82 4>;
clock-names = "clk_main", "clk_apb";
xlnx,bus-width = <64>;
+ #stream-id-cells = <1>;
+ /* iommus = <&smmu 0x86d>; */
+ power-domains = <&zynqmp_firmware PD_ADMA>;
};
lpd_dma_chan7: dma@ffae0000 {
interrupts = <0 83 4>;
clock-names = "clk_main", "clk_apb";
xlnx,bus-width = <64>;
+ #stream-id-cells = <1>;
+ /* iommus = <&smmu 0x86e>; */
+ power-domains = <&zynqmp_firmware PD_ADMA>;
};
lpd_dma_chan8: dma@ffaf0000 {
interrupts = <0 84 4>;
clock-names = "clk_main", "clk_apb";
xlnx,bus-width = <64>;
+ #stream-id-cells = <1>;
+ /* iommus = <&smmu 0x86f>; */
+ power-domains = <&zynqmp_firmware PD_ADMA>;
};
mc: memory-controller@fd070000 {
interrupts = <0 112 4>;
};
+ nand0: nand@ff100000 {
+ compatible = "arasan,nfc-v3p10";
+ status = "disabled";
+ reg = <0x0 0xff100000 0x0 0x1000>;
+ clock-names = "clk_sys", "clk_flash";
+ interrupt-parent = <&gic>;
+ interrupts = <0 14 4>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ #stream-id-cells = <1>;
+ iommus = <&smmu 0x872>;
+ power-domains = <&zynqmp_firmware PD_NAND>;
+ };
+
gem0: ethernet@ff0b0000 {
compatible = "cdns,zynqmp-gem", "cdns,gem";
status = "disabled";
clock-names = "pclk", "hclk", "tx_clk";
#address-cells = <1>;
#size-cells = <0>;
+ #stream-id-cells = <1>;
+ iommus = <&smmu 0x874>;
+ power-domains = <&zynqmp_firmware PD_ETH_0>;
};
gem1: ethernet@ff0c0000 {
clock-names = "pclk", "hclk", "tx_clk";
#address-cells = <1>;
#size-cells = <0>;
+ #stream-id-cells = <1>;
+ iommus = <&smmu 0x875>;
+ power-domains = <&zynqmp_firmware PD_ETH_1>;
};
gem2: ethernet@ff0d0000 {
clock-names = "pclk", "hclk", "tx_clk";
#address-cells = <1>;
#size-cells = <0>;
+ #stream-id-cells = <1>;
+ iommus = <&smmu 0x876>;
+ power-domains = <&zynqmp_firmware PD_ETH_2>;
};
gem3: ethernet@ff0e0000 {
clock-names = "pclk", "hclk", "tx_clk";
#address-cells = <1>;
#size-cells = <0>;
+ #stream-id-cells = <1>;
+ iommus = <&smmu 0x877>;
+ power-domains = <&zynqmp_firmware PD_ETH_3>;
};
gpio: gpio@ff0a0000 {
compatible = "xlnx,zynqmp-gpio-1.0";
status = "disabled";
#gpio-cells = <0x2>;
- gpio-controller;
interrupt-parent = <&gic>;
interrupts = <0 16 4>;
interrupt-controller;
#interrupt-cells = <2>;
reg = <0x0 0xff0a0000 0x0 0x1000>;
+ gpio-controller;
+ power-domains = <&zynqmp_firmware PD_GPIO>;
};
i2c0: i2c@ff020000 {
reg = <0x0 0xff020000 0x0 0x1000>;
#address-cells = <1>;
#size-cells = <0>;
+ power-domains = <&zynqmp_firmware PD_I2C_0>;
};
i2c1: i2c@ff030000 {
reg = <0x0 0xff030000 0x0 0x1000>;
#address-cells = <1>;
#size-cells = <0>;
+ power-domains = <&zynqmp_firmware PD_I2C_1>;
+ };
+
+ ocm: memory-controller@ff960000 {
+ compatible = "xlnx,zynqmp-ocmc-1.0";
+ reg = <0x0 0xff960000 0x0 0x1000>;
+ interrupt-parent = <&gic>;
+ interrupts = <0 10 4>;
+ };
+
+ perf_monitor_ocm: perf-monitor@ffa00000 {
+ compatible = "xlnx,axi-perf-monitor";
+ reg = <0x0 0xffa00000 0x0 0x10000>;
+ interrupts = <0 25 4>;
+ interrupt-parent = <&gic>;
+ xlnx,enable-profile = <0>;
+ xlnx,enable-trace = <0>;
+ xlnx,num-monitor-slots = <1>;
+ xlnx,enable-event-count = <1>;
+ xlnx,enable-event-log = <1>;
+ xlnx,have-sampled-metric-cnt = <1>;
+ xlnx,num-of-counters = <8>;
+ xlnx,metric-count-width = <32>;
+ xlnx,metrics-sample-count-width = <32>;
+ xlnx,global-count-width = <32>;
+ xlnx,metric-count-scale = <1>;
+ };
+
+ perf_monitor_ddr: perf-monitor@fd0b0000 {
+ compatible = "xlnx,axi-perf-monitor";
+ reg = <0x0 0xfd0b0000 0x0 0x10000>;
+ interrupts = <0 123 4>;
+ interrupt-parent = <&gic>;
+ xlnx,enable-profile = <0>;
+ xlnx,enable-trace = <0>;
+ xlnx,num-monitor-slots = <6>;
+ xlnx,enable-event-count = <1>;
+ xlnx,enable-event-log = <0>;
+ xlnx,have-sampled-metric-cnt = <1>;
+ xlnx,num-of-counters = <10>;
+ xlnx,metric-count-width = <32>;
+ xlnx,metrics-sample-count-width = <32>;
+ xlnx,global-count-width = <32>;
+ xlnx,metric-count-scale = <1>;
+ };
+
+ perf_monitor_cci: perf-monitor@fd490000 {
+ compatible = "xlnx,axi-perf-monitor";
+ reg = <0x0 0xfd490000 0x0 0x10000>;
+ interrupts = <0 123 4>;
+ interrupt-parent = <&gic>;
+ xlnx,enable-profile = <0>;
+ xlnx,enable-trace = <0>;
+ xlnx,num-monitor-slots = <1>;
+ xlnx,enable-event-count = <1>;
+ xlnx,enable-event-log = <0>;
+ xlnx,have-sampled-metric-cnt = <1>;
+ xlnx,num-of-counters = <8>;
+ xlnx,metric-count-width = <32>;
+ xlnx,metrics-sample-count-width = <32>;
+ xlnx,global-count-width = <32>;
+ xlnx,metric-count-scale = <1>;
+ };
+
+ perf_monitor_lpd: perf-monitor@ffa10000 {
+ compatible = "xlnx,axi-perf-monitor";
+ reg = <0x0 0xffa10000 0x0 0x10000>;
+ interrupts = <0 25 4>;
+ interrupt-parent = <&gic>;
+ xlnx,enable-profile = <0>;
+ xlnx,enable-trace = <0>;
+ xlnx,num-monitor-slots = <1>;
+ xlnx,enable-event-count = <1>;
+ xlnx,enable-event-log = <1>;
+ xlnx,have-sampled-metric-cnt = <1>;
+ xlnx,num-of-counters = <8>;
+ xlnx,metric-count-width = <32>;
+ xlnx,metrics-sample-count-width = <32>;
+ xlnx,global-count-width = <32>;
+ xlnx,metric-count-scale = <1>;
};
pcie: pcie@fd0e0000 {
<0x0 0x0 0x0 0x2 &pcie_intc 0x2>,
<0x0 0x0 0x0 0x3 &pcie_intc 0x3>,
<0x0 0x0 0x0 0x4 &pcie_intc 0x4>;
+ power-domains = <&zynqmp_firmware PD_PCIE>;
pcie_intc: legacy-interrupt-controller {
interrupt-controller;
#address-cells = <0>;
};
};
+ qspi: spi@ff0f0000 {
+ u-boot,dm-pre-reloc;
+ compatible = "xlnx,zynqmp-qspi-1.0";
+ status = "disabled";
+ clock-names = "ref_clk", "pclk";
+ interrupts = <0 15 4>;
+ interrupt-parent = <&gic>;
+ num-cs = <1>;
+ reg = <0x0 0xff0f0000 0x0 0x1000>,
+ <0x0 0xc0000000 0x0 0x8000000>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ #stream-id-cells = <1>;
+ iommus = <&smmu 0x873>;
+ power-domains = <&zynqmp_firmware PD_QSPI>;
+ };
+
rtc: rtc@ffa60000 {
compatible = "xlnx,zynqmp-rtc";
status = "disabled";
calibration = <0x8000>;
};
+ serdes: zynqmp_phy@fd400000 {
+ compatible = "xlnx,zynqmp-psgtr-v1.1";
+ status = "disabled";
+ reg = <0x0 0xfd400000 0x0 0x40000>,
+ <0x0 0xfd3d0000 0x0 0x1000>;
+ reg-names = "serdes", "siou";
+ nvmem-cells = <&soc_revision>;
+ nvmem-cell-names = "soc_revision";
+ resets = <&zynqmp_reset ZYNQMP_RESET_SATA>,
+ <&zynqmp_reset ZYNQMP_RESET_USB0_CORERESET>,
+ <&zynqmp_reset ZYNQMP_RESET_USB1_CORERESET>,
+ <&zynqmp_reset ZYNQMP_RESET_USB0_HIBERRESET>,
+ <&zynqmp_reset ZYNQMP_RESET_USB1_HIBERRESET>,
+ <&zynqmp_reset ZYNQMP_RESET_USB0_APB>,
+ <&zynqmp_reset ZYNQMP_RESET_USB1_APB>,
+ <&zynqmp_reset ZYNQMP_RESET_DP>,
+ <&zynqmp_reset ZYNQMP_RESET_GEM0>,
+ <&zynqmp_reset ZYNQMP_RESET_GEM1>,
+ <&zynqmp_reset ZYNQMP_RESET_GEM2>,
+ <&zynqmp_reset ZYNQMP_RESET_GEM3>;
+ reset-names = "sata_rst", "usb0_crst", "usb1_crst",
+ "usb0_hibrst", "usb1_hibrst", "usb0_apbrst",
+ "usb1_apbrst", "dp_rst", "gem0_rst",
+ "gem1_rst", "gem2_rst", "gem3_rst";
+ lane0: lane0 {
+ #phy-cells = <4>;
+ };
+ lane1: lane1 {
+ #phy-cells = <4>;
+ };
+ lane2: lane2 {
+ #phy-cells = <4>;
+ };
+ lane3: lane3 {
+ #phy-cells = <4>;
+ };
+ };
+
sata: ahci@fd0c0000 {
compatible = "ceva,ahci-1v84";
status = "disabled";
reg = <0x0 0xfd0c0000 0x0 0x2000>;
interrupt-parent = <&gic>;
interrupts = <0 133 4>;
+ power-domains = <&zynqmp_firmware PD_SATA>;
+ #stream-id-cells = <4>;
+ /* iommus = <&smmu 0x4c0>, <&smmu 0x4c1>, */
+ /* <&smmu 0x4c2>, <&smmu 0x4c3>; */
+ /* dma-coherent; */
};
sdhci0: mmc@ff160000 {
- compatible = "arasan,sdhci-8.9a";
+ u-boot,dm-pre-reloc;
+ compatible = "xlnx,zynqmp-8.9a", "arasan,sdhci-8.9a";
status = "disabled";
interrupt-parent = <&gic>;
interrupts = <0 48 4>;
reg = <0x0 0xff160000 0x0 0x1000>;
clock-names = "clk_xin", "clk_ahb";
+ xlnx,device_id = <0>;
+ #stream-id-cells = <1>;
+ iommus = <&smmu 0x870>;
+ power-domains = <&zynqmp_firmware PD_SD_0>;
+ nvmem-cells = <&soc_revision>;
+ nvmem-cell-names = "soc_revision";
};
sdhci1: mmc@ff170000 {
- compatible = "arasan,sdhci-8.9a";
+ u-boot,dm-pre-reloc;
+ compatible = "xlnx,zynqmp-8.9a", "arasan,sdhci-8.9a";
status = "disabled";
interrupt-parent = <&gic>;
interrupts = <0 49 4>;
reg = <0x0 0xff170000 0x0 0x1000>;
clock-names = "clk_xin", "clk_ahb";
- };
-
- smmu: smmu@fd800000 {
- compatible = "arm,mmu-500";
- reg = <0x0 0xfd800000 0x0 0x20000>;
- status = "disabled";
- #global-interrupts = <1>;
- interrupt-parent = <&gic>;
- interrupts = <0 155 4>,
- <0 155 4>, <0 155 4>, <0 155 4>, <0 155 4>,
- <0 155 4>, <0 155 4>, <0 155 4>, <0 155 4>,
- <0 155 4>, <0 155 4>, <0 155 4>, <0 155 4>,
- <0 155 4>, <0 155 4>, <0 155 4>, <0 155 4>;
+ xlnx,device_id = <1>;
+ #stream-id-cells = <1>;
+ iommus = <&smmu 0x871>;
+ power-domains = <&zynqmp_firmware PD_SD_1>;
+ nvmem-cells = <&soc_revision>;
+ nvmem-cell-names = "soc_revision";
};
spi0: spi@ff040000 {
clock-names = "ref_clk", "pclk";
#address-cells = <1>;
#size-cells = <0>;
+ power-domains = <&zynqmp_firmware PD_SPI_0>;
};
spi1: spi@ff050000 {
clock-names = "ref_clk", "pclk";
#address-cells = <1>;
#size-cells = <0>;
+ power-domains = <&zynqmp_firmware PD_SPI_1>;
};
ttc0: timer@ff110000 {
interrupts = <0 36 4>, <0 37 4>, <0 38 4>;
reg = <0x0 0xff110000 0x0 0x1000>;
timer-width = <32>;
+ power-domains = <&zynqmp_firmware PD_TTC_0>;
};
ttc1: timer@ff120000 {
interrupts = <0 39 4>, <0 40 4>, <0 41 4>;
reg = <0x0 0xff120000 0x0 0x1000>;
timer-width = <32>;
+ power-domains = <&zynqmp_firmware PD_TTC_1>;
};
ttc2: timer@ff130000 {
interrupts = <0 42 4>, <0 43 4>, <0 44 4>;
reg = <0x0 0xff130000 0x0 0x1000>;
timer-width = <32>;
+ power-domains = <&zynqmp_firmware PD_TTC_2>;
};
ttc3: timer@ff140000 {
interrupts = <0 45 4>, <0 46 4>, <0 47 4>;
reg = <0x0 0xff140000 0x0 0x1000>;
timer-width = <32>;
+ power-domains = <&zynqmp_firmware PD_TTC_3>;
};
uart0: serial@ff000000 {
+ u-boot,dm-pre-reloc;
compatible = "cdns,uart-r1p12", "xlnx,xuartps";
status = "disabled";
interrupt-parent = <&gic>;
interrupts = <0 21 4>;
reg = <0x0 0xff000000 0x0 0x1000>;
clock-names = "uart_clk", "pclk";
+ power-domains = <&zynqmp_firmware PD_UART_0>;
};
uart1: serial@ff010000 {
+ u-boot,dm-pre-reloc;
compatible = "cdns,uart-r1p12", "xlnx,xuartps";
status = "disabled";
interrupt-parent = <&gic>;
interrupts = <0 22 4>;
reg = <0x0 0xff010000 0x0 0x1000>;
clock-names = "uart_clk", "pclk";
+ power-domains = <&zynqmp_firmware PD_UART_1>;
};
- usb0: usb@fe200000 {
- compatible = "snps,dwc3";
+ usb0: usb0@ff9d0000 {
+ #address-cells = <2>;
+ #size-cells = <2>;
status = "disabled";
- interrupt-parent = <&gic>;
- interrupts = <0 65 4>;
- reg = <0x0 0xfe200000 0x0 0x40000>;
- clock-names = "clk_xin", "clk_ahb";
+ compatible = "xlnx,zynqmp-dwc3";
+ reg = <0x0 0xff9d0000 0x0 0x100>;
+ clock-names = "bus_clk", "ref_clk";
+ power-domains = <&zynqmp_firmware PD_USB_0>;
+ ranges;
+ nvmem-cells = <&soc_revision>;
+ nvmem-cell-names = "soc_revision";
+
+ dwc3_0: dwc3@fe200000 {
+ compatible = "snps,dwc3";
+ status = "disabled";
+ reg = <0x0 0xfe200000 0x0 0x40000>;
+ interrupt-parent = <&gic>;
+ interrupt-names = "dwc_usb3", "otg", "hiber";
+ interrupts = <0 65 4>, <0 69 4>, <0 75 4>;
+ #stream-id-cells = <1>;
+ iommus = <&smmu 0x860>;
+ snps,quirk-frame-length-adjustment = <0x20>;
+ snps,refclk_fladj;
+ snps,enable_guctl1_resume_quirk;
+ snps,enable_guctl1_ipd_quirk;
+ snps,xhci-stream-quirk;
+ /* dma-coherent; */
+ /* snps,enable-hibernation; */
+ };
};
- usb1: usb@fe300000 {
- compatible = "snps,dwc3";
+ usb1: usb1@ff9e0000 {
+ #address-cells = <2>;
+ #size-cells = <2>;
status = "disabled";
- interrupt-parent = <&gic>;
- interrupts = <0 70 4>;
- reg = <0x0 0xfe300000 0x0 0x40000>;
- clock-names = "clk_xin", "clk_ahb";
+ compatible = "xlnx,zynqmp-dwc3";
+ reg = <0x0 0xff9e0000 0x0 0x100>;
+ clock-names = "bus_clk", "ref_clk";
+ power-domains = <&zynqmp_firmware PD_USB_1>;
+ ranges;
+ nvmem-cells = <&soc_revision>;
+ nvmem-cell-names = "soc_revision";
+
+ dwc3_1: dwc3@fe300000 {
+ compatible = "snps,dwc3";
+ status = "disabled";
+ reg = <0x0 0xfe300000 0x0 0x40000>;
+ interrupt-parent = <&gic>;
+ interrupt-names = "dwc_usb3", "otg", "hiber";
+ interrupts = <0 70 4>, <0 74 4>, <0 76 4>;
+ #stream-id-cells = <1>;
+ iommus = <&smmu 0x861>;
+ snps,quirk-frame-length-adjustment = <0x20>;
+ snps,refclk_fladj;
+ snps,enable_guctl1_resume_quirk;
+ snps,enable_guctl1_ipd_quirk;
+ snps,xhci-stream-quirk;
+ /* dma-coherent; */
+ };
};
watchdog0: watchdog@fd4d0000 {
interrupt-parent = <&gic>;
interrupts = <0 113 1>;
reg = <0x0 0xfd4d0000 0x0 0x1000>;
+ timeout-sec = <60>;
+ reset-on-timeout;
+ };
+
+ lpd_watchdog: watchdog@ff150000 {
+ compatible = "cdns,wdt-r1p2";
+ status = "disabled";
+ interrupt-parent = <&gic>;
+ interrupts = <0 52 1>;
+ reg = <0x0 0xff150000 0x0 0x1000>;
timeout-sec = <10>;
};
+
+ xilinx_ams: ams@ffa50000 {
+ compatible = "xlnx,zynqmp-ams";
+ status = "disabled";
+ interrupt-parent = <&gic>;
+ interrupts = <0 56 4>;
+ interrupt-names = "ams-irq";
+ reg = <0x0 0xffa50000 0x0 0x800>;
+ reg-names = "ams-base";
+ #address-cells = <2>;
+ #size-cells = <2>;
+ #io-channel-cells = <1>;
+ ranges;
+
+ ams_ps: ams_ps@ffa50800 {
+ compatible = "xlnx,zynqmp-ams-ps";
+ status = "disabled";
+ reg = <0x0 0xffa50800 0x0 0x400>;
+ };
+
+ ams_pl: ams_pl@ffa50c00 {
+ compatible = "xlnx,zynqmp-ams-pl";
+ status = "disabled";
+ reg = <0x0 0xffa50c00 0x0 0x400>;
+ };
+ };
+
+ xlnx_dpdma: dma@fd4c0000 {
+ compatible = "xlnx,dpdma";
+ status = "disabled";
+ reg = <0x0 0xfd4c0000 0x0 0x1000>;
+ interrupts = <0 122 4>;
+ interrupt-parent = <&gic>;
+ clock-names = "axi_clk";
+ power-domains = <&zynqmp_firmware PD_DP>;
+ dma-channels = <6>;
+ #dma-cells = <1>;
+ dma-video0channel {
+ compatible = "xlnx,video0";
+ };
+ dma-video1channel {
+ compatible = "xlnx,video1";
+ };
+ dma-video2channel {
+ compatible = "xlnx,video2";
+ };
+ dma-graphicschannel {
+ compatible = "xlnx,graphics";
+ };
+ dma-audio0channel {
+ compatible = "xlnx,audio0";
+ };
+ dma-audio1channel {
+ compatible = "xlnx,audio1";
+ };
+ };
+
+ zynqmp_dpsub: zynqmp-display@fd4a0000 {
+ compatible = "xlnx,zynqmp-dpsub-1.7";
+ status = "disabled";
+ reg = <0x0 0xfd4a0000 0x0 0x1000>,
+ <0x0 0xfd4aa000 0x0 0x1000>,
+ <0x0 0xfd4ab000 0x0 0x1000>,
+ <0x0 0xfd4ac000 0x0 0x1000>;
+ reg-names = "dp", "blend", "av_buf", "aud";
+ interrupts = <0 119 4>;
+ interrupt-parent = <&gic>;
+
+ clock-names = "dp_apb_clk", "dp_aud_clk",
+ "dp_vtc_pixel_clk_in";
+
+ power-domains = <&zynqmp_firmware PD_DP>;
+
+ vid-layer {
+ dma-names = "vid0", "vid1", "vid2";
+ dmas = <&xlnx_dpdma 0>,
+ <&xlnx_dpdma 1>,
+ <&xlnx_dpdma 2>;
+ };
+
+ gfx-layer {
+ dma-names = "gfx0";
+ dmas = <&xlnx_dpdma 3>;
+ };
+
+ /* dummy node to indicate there's no child i2c device */
+ i2c-bus {
+ };
+
+ zynqmp_dp_snd_codec0: zynqmp_dp_snd_codec0 {
+ compatible = "xlnx,dp-snd-codec";
+ clock-names = "aud_clk";
+ };
+
+ zynqmp_dp_snd_pcm0: zynqmp_dp_snd_pcm0 {
+ compatible = "xlnx,dp-snd-pcm";
+ dmas = <&xlnx_dpdma 4>;
+ dma-names = "tx";
+ };
+
+ zynqmp_dp_snd_pcm1: zynqmp_dp_snd_pcm1 {
+ compatible = "xlnx,dp-snd-pcm";
+ dmas = <&xlnx_dpdma 5>;
+ dma-names = "tx";
+ };
+
+ zynqmp_dp_snd_card0: zynqmp_dp_snd_card {
+ compatible = "xlnx,dp-snd-card";
+ xlnx,dp-snd-pcm = <&zynqmp_dp_snd_pcm0>,
+ <&zynqmp_dp_snd_pcm1>;
+ xlnx,dp-snd-codec = <&zynqmp_dp_snd_codec0>;
+ };
+ };
};
};
projects / zynq / linux.git / commitdiff