TMS570LS3137

Documentation

• Main TI page containing datasheets.
• TI TMS570 related forum
• TMS570 Wiki

• LwIP integration

• Media:Studim_procesoru.pdf Notes from documentation (in Czech language)

Programming

Tools recommended by TI for programming of this microcontroller:

• Code Composer Studio (runs on Win and Linux).
• HalCoGen (for Windows only, but also runs quite well in Wine).
  • TMS570LS3137 HalCoGen Bugs

Installing CCS5 in Ubuntu 12.04 65bits

After installation the application can be run with:

cd <install_dir>/ccsv5/eclipse/

./ccstudio

If the application fails to start is because CCS5 is a 32bits application a thus requires 32bits libraries:

sudo apt-get install libgtk2.0-0:i386 libxtst6:i386

If the application crashes with a segmentation fault do:

Edit <install_dir>/ccsv5/eclipse/plugins/com.ti.ccstudio.branding_<your version number>/plugin_customization.ini

And change key org.eclipse.ui/showIntro" to false.

FreeRTOS

Installation is easy, simply create new project in HalCoGen

• New -> Project
• Select Family:TMS570LS31x
• Select Device: TMS570LS3137ZWT_FREERTOS

All necessary files will be added into project automaticaly.

Hardware

Developement board we are using: TMS570LS31x_HDK_Kit

SCI port

We have connected serial port on Expansion Connector P3 (see HDK documentation) pin W3 and N2. TX is connected to N2 pin and RX to W3 pin. This brings us consequences as both pins are mutexed.

When you want to use SCI, you have to set few things in HalCoGen.

• Enable driver SCI (not LIN or SCI2 driver)
• In tab PINMUX select SCI and check conflict with other drivers
• In tab SCI choose and set data format.

When you want use interrupts in adittion, do the following:

• In tab VIM Channel 64-95 select interrupt 64: SCI level0 interrupt for high level interrupt or 74: SCI Level1 for low level interrupt
• In SCI tab enable TX and/or RX interrupt and select High or Low.
• In your code enable IRQ using _enable_IRQ() function, than enable notification using sciEnableNotification() function.
• Implement notification callback sciNotification() in notificatin.c

In your code don't forget to initialize sci using sciInit() function.

Debug over JTAG

XDS100v2 JTAG Interface from Ti

The XDS100v2 is equipped with Ti specific 14-pin JTAG connector. Next cable wires placement allows to use it with TMS570LS31x_HDK_Kit or other device with ARM JTAG pin placement.

14 pin Ti		20 pin ARM
1	TMS	TMS	7
2	TRST	NTRST	3
3	TDI	TDI	5
4	DIS	GND	6
5	VD	VREF	1 (2)
6	NC		--
7	TDO	TDO	13
8	GND	GND	(4)
9	RTCK	RTCK	11
10	GND	GND	8 (12)
11	TCK	TCK	9
12	GND	GND	10 (14)
13	EMU0
14	EMU1

Setup XDS100v2 on Linux

By default the device (if nothing more connected then /dev/ttyUSB0) is added with permissions 664 with root as user and group. You access the device we need write access for current user. To do so we need to create a new udev rules:

sudo nano /etc/udev/rules.d/45-pes-rpp.rules

And add line:

SUBSYSTEM=="usb", ATTR{idVendor}=="0403", ATTR{idProduct}=="a6d0", MODE="0660", GROUP="plugdev"

Then reload udev rules with:

sudo udevadm control --reload-rules

You can check device properties like idVendor or idProduct with the following command:

udevadm info -a -p $(udevadm info -q path -n /dev/ttyUSB0)

RS232 communication setup

Connect serial communication pins to computer's RS232 port or to USB through a FTDI adapter. If using RS232 port the device should be /dev/ttyS0, if using FTDI it should be something like /dev/ttyUSBx (check dmesg for details).

Make sure minicom or similar terminal program is installed:

sudo apt-get install minicom

Then configure minicon:

sudo minicom -s

And use the following configuration "9600 81N":

Serial Device         : /dev/ttyS0
Lockfile Location     : /var/lock
Callin Program        :
Callout Program       :
Bps/Par/Bits          : 9600 8N1
Hardware Flow Control : No
Software Flow Control : No

Start terminal session and type HELP command to test communication.

Contacts

• Management: Prof. Zdeněk Hanzálek
• Technical: Pavel Píša, Ph.D.