/*
* DA8xx USB
*/
+#include <linux/clk.h>
+#include <linux/delay.h>
#include <linux/dma-mapping.h>
#include <linux/init.h>
+#include <linux/mfd/da8xx-cfgchip.h>
#include <linux/phy/phy.h>
#include <linux/platform_data/usb-davinci.h>
#include <linux/platform_device.h>
#include <linux/usb/musb.h>
+#include <mach/clock.h>
#include <mach/common.h>
#include <mach/cputype.h>
#include <mach/da8xx.h>
#include <mach/irqs.h>
+#include "clock.h"
+
#define DA8XX_USB0_BASE 0x01e00000
#define DA8XX_USB1_BASE 0x01e25000
static struct platform_device da8xx_usb_phy = {
.name = "da8xx-usb-phy",
.id = -1,
+ .dev = {
+ /*
+ * Setting init_name so that clock lookup will work in
+ * da8xx_register_usb11_phy_clk() even if this device is not
+ * registered yet.
+ */
+ .init_name = "da8xx-usb-phy",
+ },
};
int __init da8xx_register_usb_phy(void)
return platform_device_register(&da8xx_usb_phy);
}
-#if IS_ENABLED(CONFIG_USB_MUSB_HDRC)
-
static struct musb_hdrc_config musb_config = {
.multipoint = true,
.num_eps = 5,
static u64 usb_dmamask = DMA_BIT_MASK(32);
-static struct platform_device usb_dev = {
+static struct platform_device da8xx_usb20_dev = {
.name = "musb-da8xx",
.id = -1,
.dev = {
+ /*
+ * Setting init_name so that clock lookup will work in
+ * usb20_phy_clk_enable() even if this device is not registered.
+ */
+ .init_name = "musb-da8xx",
.platform_data = &usb_data,
.dma_mask = &usb_dmamask,
.coherent_dma_mask = DMA_BIT_MASK(32),
usb_data.power = mA > 510 ? 255 : mA / 2;
usb_data.potpgt = (potpgt + 1) / 2;
- return platform_device_register(&usb_dev);
-}
-
-#else
-
-int __init da8xx_register_usb20(unsigned int mA, unsigned int potpgt)
-{
- return 0;
+ return platform_device_register(&da8xx_usb20_dev);
}
-#endif /* CONFIG_USB_MUSB_HDRC */
-
static struct resource da8xx_usb11_resources[] = {
[0] = {
.start = DA8XX_USB1_BASE,
da8xx_usb11_device.dev.platform_data = pdata;
return platform_device_register(&da8xx_usb11_device);
}
+
+static struct clk usb_refclkin = {
+ .name = "usb_refclkin",
+ .set_rate = davinci_simple_set_rate,
+};
+
+static struct clk_lookup usb_refclkin_lookup =
+ CLK(NULL, "usb_refclkin", &usb_refclkin);
+
+/**
+ * da8xx_register_usb_refclkin - register USB_REFCLKIN clock
+ *
+ * @rate: The clock rate in Hz
+ *
+ * This clock is only needed if the board provides an external USB_REFCLKIN
+ * signal, in which case it will be used as the parent of usb20_phy_clk and/or
+ * usb11_phy_clk.
+ */
+int __init da8xx_register_usb_refclkin(int rate)
+{
+ int ret;
+
+ usb_refclkin.rate = rate;
+ ret = clk_register(&usb_refclkin);
+ if (ret)
+ return ret;
+
+ clkdev_add(&usb_refclkin_lookup);
+
+ return 0;
+}
+
+static void usb20_phy_clk_enable(struct clk *clk)
+{
+ struct clk *usb20_clk;
+ int err;
+ u32 val;
+ u32 timeout = 500000; /* 500 msec */
+
+ val = readl(DA8XX_SYSCFG0_VIRT(DA8XX_CFGCHIP2_REG));
+
+ usb20_clk = clk_get(&da8xx_usb20_dev.dev, "usb20");
+ if (IS_ERR(usb20_clk)) {
+ pr_err("could not get usb20 clk: %ld\n", PTR_ERR(usb20_clk));
+ return;
+ }
+
+ /* The USB 2.O PLL requires that the USB 2.O PSC is enabled as well. */
+ err = clk_prepare_enable(usb20_clk);
+ if (err) {
+ pr_err("failed to enable usb20 clk: %d\n", err);
+ clk_put(usb20_clk);
+ return;
+ }
+
+ /*
+ * Turn on the USB 2.0 PHY, but just the PLL, and not OTG. The USB 1.1
+ * host may use the PLL clock without USB 2.0 OTG being used.
+ */
+ val &= ~(CFGCHIP2_RESET | CFGCHIP2_PHYPWRDN);
+ val |= CFGCHIP2_PHY_PLLON;
+
+ writel(val, DA8XX_SYSCFG0_VIRT(DA8XX_CFGCHIP2_REG));
+
+ while (--timeout) {
+ val = readl(DA8XX_SYSCFG0_VIRT(DA8XX_CFGCHIP2_REG));
+ if (val & CFGCHIP2_PHYCLKGD)
+ goto done;
+ udelay(1);
+ }
+
+ pr_err("Timeout waiting for USB 2.0 PHY clock good\n");
+done:
+ clk_disable_unprepare(usb20_clk);
+ clk_put(usb20_clk);
+}
+
+static void usb20_phy_clk_disable(struct clk *clk)
+{
+ u32 val;
+
+ val = readl(DA8XX_SYSCFG0_VIRT(DA8XX_CFGCHIP2_REG));
+ val |= CFGCHIP2_PHYPWRDN;
+ writel(val, DA8XX_SYSCFG0_VIRT(DA8XX_CFGCHIP2_REG));
+}
+
+static int usb20_phy_clk_set_parent(struct clk *clk, struct clk *parent)
+{
+ u32 val;
+
+ val = readl(DA8XX_SYSCFG0_VIRT(DA8XX_CFGCHIP2_REG));
+
+ /* Set the mux depending on the parent clock. */
+ if (parent == &usb_refclkin) {
+ val &= ~CFGCHIP2_USB2PHYCLKMUX;
+ } else if (strcmp(parent->name, "pll0_aux_clk") == 0) {
+ val |= CFGCHIP2_USB2PHYCLKMUX;
+ } else {
+ pr_err("Bad parent on USB 2.0 PHY clock\n");
+ return -EINVAL;
+ }
+
+ /* reference frequency also comes from parent clock */
+ val &= ~CFGCHIP2_REFFREQ_MASK;
+ switch (clk_get_rate(parent)) {
+ case 12000000:
+ val |= CFGCHIP2_REFFREQ_12MHZ;
+ break;
+ case 13000000:
+ val |= CFGCHIP2_REFFREQ_13MHZ;
+ break;
+ case 19200000:
+ val |= CFGCHIP2_REFFREQ_19_2MHZ;
+ break;
+ case 20000000:
+ val |= CFGCHIP2_REFFREQ_20MHZ;
+ break;
+ case 24000000:
+ val |= CFGCHIP2_REFFREQ_24MHZ;
+ break;
+ case 26000000:
+ val |= CFGCHIP2_REFFREQ_26MHZ;
+ break;
+ case 38400000:
+ val |= CFGCHIP2_REFFREQ_38_4MHZ;
+ break;
+ case 40000000:
+ val |= CFGCHIP2_REFFREQ_40MHZ;
+ break;
+ case 48000000:
+ val |= CFGCHIP2_REFFREQ_48MHZ;
+ break;
+ default:
+ pr_err("Bad parent clock rate on USB 2.0 PHY clock\n");
+ return -EINVAL;
+ }
+
+ writel(val, DA8XX_SYSCFG0_VIRT(DA8XX_CFGCHIP2_REG));
+
+ return 0;
+}
+
+static struct clk usb20_phy_clk = {
+ .name = "usb20_phy",
+ .clk_enable = usb20_phy_clk_enable,
+ .clk_disable = usb20_phy_clk_disable,
+ .set_parent = usb20_phy_clk_set_parent,
+};
+
+static struct clk_lookup usb20_phy_clk_lookup =
+ CLK("da8xx-usb-phy", "usb20_phy", &usb20_phy_clk);
+
+/**
+ * da8xx_register_usb20_phy_clk - register USB0PHYCLKMUX clock
+ *
+ * @use_usb_refclkin: Selects the parent clock - either "usb_refclkin" if true
+ * or "pll0_aux" if false.
+ */
+int __init da8xx_register_usb20_phy_clk(bool use_usb_refclkin)
+{
+ struct clk *parent;
+ int ret = 0;
+
+ parent = clk_get(NULL, use_usb_refclkin ? "usb_refclkin" : "pll0_aux");
+ if (IS_ERR(parent))
+ return PTR_ERR(parent);
+
+ usb20_phy_clk.parent = parent;
+ ret = clk_register(&usb20_phy_clk);
+ if (!ret)
+ clkdev_add(&usb20_phy_clk_lookup);
+
+ clk_put(parent);
+
+ return ret;
+}
+
+static int usb11_phy_clk_set_parent(struct clk *clk, struct clk *parent)
+{
+ u32 val;
+
+ val = readl(DA8XX_SYSCFG0_VIRT(DA8XX_CFGCHIP2_REG));
+
+ /* Set the USB 1.1 PHY clock mux based on the parent clock. */
+ if (parent == &usb20_phy_clk) {
+ val &= ~CFGCHIP2_USB1PHYCLKMUX;
+ } else if (parent == &usb_refclkin) {
+ val |= CFGCHIP2_USB1PHYCLKMUX;
+ } else {
+ pr_err("Bad parent on USB 1.1 PHY clock\n");
+ return -EINVAL;
+ }
+
+ writel(val, DA8XX_SYSCFG0_VIRT(DA8XX_CFGCHIP2_REG));
+
+ return 0;
+}
+
+static struct clk usb11_phy_clk = {
+ .name = "usb11_phy",
+ .set_parent = usb11_phy_clk_set_parent,
+};
+
+static struct clk_lookup usb11_phy_clk_lookup =
+ CLK("da8xx-usb-phy", "usb11_phy", &usb11_phy_clk);
+
+/**
+ * da8xx_register_usb11_phy_clk - register USB1PHYCLKMUX clock
+ *
+ * @use_usb_refclkin: Selects the parent clock - either "usb_refclkin" if true
+ * or "usb20_phy" if false.
+ */
+int __init da8xx_register_usb11_phy_clk(bool use_usb_refclkin)
+{
+ struct clk *parent;
+ int ret = 0;
+
+ if (use_usb_refclkin)
+ parent = clk_get(NULL, "usb_refclkin");
+ else
+ parent = clk_get(&da8xx_usb_phy.dev, "usb20_phy");
+ if (IS_ERR(parent))
+ return PTR_ERR(parent);
+
+ usb11_phy_clk.parent = parent;
+ ret = clk_register(&usb11_phy_clk);
+ if (!ret)
+ clkdev_add(&usb11_phy_clk_lookup);
+
+ clk_put(parent);
+
+ return ret;
+}
projects / zynq / linux.git / commitdiff