if (HAS_PCH_SPLIT(dev))
return;
- /* Who knows what state these registers were left in by the BIOS or
- * grub?
- *
- * If we leave the registers in a conflicting state (e.g. with the
- * display plane reading from the other pipe than the one we intend
- * to use) then when we attempt to teardown the active mode, we will
- * not disable the pipes and planes in the correct order -- leaving
- * a plane reading from a disabled pipe and possibly leading to
- * undefined behaviour.
- */
+ if (!dev_priv->lvds_downclock_avail)
+ return;
- reg = DSPCNTR(plane);
- val = I915_READ(reg);
+ dpll = I915_READ(dpll_reg);
+ if (!HAS_PIPE_CXSR(dev) && (dpll & DISPLAY_RATE_SELECT_FPA1)) {
+ DRM_DEBUG_DRIVER("upclocking LVDS\n");
- if ((val & DISPLAY_PLANE_ENABLE) == 0)
- return;
- if (!!(val & DISPPLANE_SEL_PIPE_MASK) == pipe)
- return;
+ assert_panel_unlocked(dev_priv, pipe);
- /* This display plane is active and attached to the other CPU pipe. */
- pipe = !pipe;
+ dpll &= ~DISPLAY_RATE_SELECT_FPA1;
+ I915_WRITE(dpll_reg, dpll);
+ intel_wait_for_vblank(dev, pipe);
- /* Disable the plane and wait for it to stop reading from the pipe. */
- intel_disable_plane(dev_priv, plane, pipe);
- intel_disable_pipe(dev_priv, pipe);
+ dpll = I915_READ(dpll_reg);
+ if (dpll & DISPLAY_RATE_SELECT_FPA1)
+ DRM_DEBUG_DRIVER("failed to upclock LVDS!\n");
+ }
+
+ /* Schedule downclock */
+ mod_timer(&intel_crtc->idle_timer, jiffies +
+ msecs_to_jiffies(CRTC_IDLE_TIMEOUT));
}
-static void intel_crtc_reset(struct drm_crtc *crtc)
+static void intel_decrease_pllclock(struct drm_crtc *crtc)
{
struct drm_device *dev = crtc->dev;
+ drm_i915_private_t *dev_priv = dev->dev_private;
struct intel_crtc *intel_crtc = to_intel_crtc(crtc);
- int pipe = intel_crtc->pipe;
- int dpll_reg = DPLL(pipe);
- int dpll = I915_READ(dpll_reg);
- /* Reset flags back to the 'unknown' status so that they
- * will be correctly set on the initial modeset.
- */
- intel_crtc->dpms_mode = -1;
+ if (HAS_PCH_SPLIT(dev))
+ return;
- /* We need to fix up any BIOS configuration that conflicts with
- * our expectations.
+ if (!dev_priv->lvds_downclock_avail)
+ return;
+
+ /*
+ * Since this is called by a timer, we should never get here in
+ * the manual case.
*/
- intel_sanitize_modesetting(dev, intel_crtc->pipe, intel_crtc->plane);
-}
+ if (!HAS_PIPE_CXSR(dev) && intel_crtc->lowfreq_avail) {
++ int pipe = intel_crtc->pipe;
++ int dpll_reg = DPLL(pipe);
++ int dpll;
+
-static struct drm_crtc_helper_funcs intel_helper_funcs = {
- .dpms = intel_crtc_dpms,
- .mode_fixup = intel_crtc_mode_fixup,
- .mode_set = intel_crtc_mode_set,
- .mode_set_base = intel_pipe_set_base,
- .mode_set_base_atomic = intel_pipe_set_base_atomic,
- .load_lut = intel_crtc_load_lut,
- .disable = intel_crtc_disable,
-};
+ DRM_DEBUG_DRIVER("downclocking LVDS\n");
-static const struct drm_crtc_funcs intel_crtc_funcs = {
- .reset = intel_crtc_reset,
- .cursor_set = intel_crtc_cursor_set,
- .cursor_move = intel_crtc_cursor_move,
- .gamma_set = intel_crtc_gamma_set,
- .set_config = drm_crtc_helper_set_config,
- .destroy = intel_crtc_destroy,
- .page_flip = intel_crtc_page_flip,
-};
+ assert_panel_unlocked(dev_priv, pipe);
-static void intel_crtc_init(struct drm_device *dev, int pipe)
++ dpll = I915_READ(dpll_reg);
+ dpll |= DISPLAY_RATE_SELECT_FPA1;
+ I915_WRITE(dpll_reg, dpll);
+ intel_wait_for_vblank(dev, pipe);
+ dpll = I915_READ(dpll_reg);
+ if (!(dpll & DISPLAY_RATE_SELECT_FPA1))
+ DRM_DEBUG_DRIVER("failed to downclock LVDS!\n");
+ }
+
+}
+
+/**
+ * intel_idle_update - adjust clocks for idleness
+ * @work: work struct
+ *
+ * Either the GPU or display (or both) went idle. Check the busy status
+ * here and adjust the CRTC and GPU clocks as necessary.
+ */
+static void intel_idle_update(struct work_struct *work)
{
- drm_i915_private_t *dev_priv = dev->dev_private;
+ drm_i915_private_t *dev_priv = container_of(work, drm_i915_private_t,
+ idle_work);
+ struct drm_device *dev = dev_priv->dev;
+ struct drm_crtc *crtc;
struct intel_crtc *intel_crtc;
- int i;
- intel_crtc = kzalloc(sizeof(struct intel_crtc) + (INTELFB_CONN_LIMIT * sizeof(struct drm_connector *)), GFP_KERNEL);
- if (intel_crtc == NULL)
+ if (!i915_powersave)
return;
- drm_crtc_init(dev, &intel_crtc->base, &intel_crtc_funcs);
+ mutex_lock(&dev->struct_mutex);
- drm_mode_crtc_set_gamma_size(&intel_crtc->base, 256);
- for (i = 0; i < 256; i++) {
- intel_crtc->lut_r[i] = i;
- intel_crtc->lut_g[i] = i;
- intel_crtc->lut_b[i] = i;
- }
+ i915_update_gfx_val(dev_priv);
- /* Swap pipes & planes for FBC on pre-965 */
- intel_crtc->pipe = pipe;
- intel_crtc->plane = pipe;
- if (IS_MOBILE(dev) && IS_GEN3(dev)) {
- DRM_DEBUG_KMS("swapping pipes & planes for FBC\n");
- intel_crtc->plane = !pipe;
+ list_for_each_entry(crtc, &dev->mode_config.crtc_list, head) {
+ /* Skip inactive CRTCs */
+ if (!crtc->fb)
+ continue;
+
+ intel_crtc = to_intel_crtc(crtc);
+ if (!intel_crtc->busy)
+ intel_decrease_pllclock(crtc);
}
- BUG_ON(pipe >= ARRAY_SIZE(dev_priv->plane_to_crtc_mapping) ||
- dev_priv->plane_to_crtc_mapping[intel_crtc->plane] != NULL);
- dev_priv->plane_to_crtc_mapping[intel_crtc->plane] = &intel_crtc->base;
- dev_priv->pipe_to_crtc_mapping[intel_crtc->pipe] = &intel_crtc->base;
- intel_crtc_reset(&intel_crtc->base);
- intel_crtc->active = true; /* force the pipe off on setup_init_config */
- intel_crtc->bpp = 24; /* default for pre-Ironlake */
+ mutex_unlock(&dev->struct_mutex);
+}
- if (HAS_PCH_SPLIT(dev)) {
- if (pipe == 2 && IS_IVYBRIDGE(dev))
- intel_crtc->no_pll = true;
- intel_helper_funcs.prepare = ironlake_crtc_prepare;
- intel_helper_funcs.commit = ironlake_crtc_commit;
- } else {
- intel_helper_funcs.prepare = i9xx_crtc_prepare;
- intel_helper_funcs.commit = i9xx_crtc_commit;
- }
+/**
+ * intel_mark_busy - mark the GPU and possibly the display busy
+ * @dev: drm device
+ * @obj: object we're operating on
+ *
+ * Callers can use this function to indicate that the GPU is busy processing
+ * commands. If @obj matches one of the CRTC objects (i.e. it's a scanout
+ * buffer), we'll also mark the display as busy, so we know to increase its
+ * clock frequency.
+ */
+void intel_mark_busy(struct drm_device *dev, struct drm_i915_gem_object *obj)
+{
+ drm_i915_private_t *dev_priv = dev->dev_private;
+ struct drm_crtc *crtc = NULL;
+ struct intel_framebuffer *intel_fb;
+ struct intel_crtc *intel_crtc;
- drm_crtc_helper_add(&intel_crtc->base, &intel_helper_funcs);
+ if (!drm_core_check_feature(dev, DRIVER_MODESET))
+ return;
- intel_crtc->busy = false;
+ if (!dev_priv->busy)
+ dev_priv->busy = true;
+ else
+ mod_timer(&dev_priv->idle_timer, jiffies +
+ msecs_to_jiffies(GPU_IDLE_TIMEOUT));
- setup_timer(&intel_crtc->idle_timer, intel_crtc_idle_timer,
- (unsigned long)intel_crtc);
+ list_for_each_entry(crtc, &dev->mode_config.crtc_list, head) {
+ if (!crtc->fb)
+ continue;
+
+ intel_crtc = to_intel_crtc(crtc);
+ intel_fb = to_intel_framebuffer(crtc->fb);
+ if (intel_fb->obj == obj) {
+ if (!intel_crtc->busy) {
+ /* Non-busy -> busy, upclock */
+ intel_increase_pllclock(crtc);
+ intel_crtc->busy = true;
+ } else {
+ /* Busy -> busy, put off timer */
+ mod_timer(&intel_crtc->idle_timer, jiffies +
+ msecs_to_jiffies(CRTC_IDLE_TIMEOUT));
+ }
+ }
+ }
}
-int intel_get_pipe_from_crtc_id(struct drm_device *dev, void *data,
- struct drm_file *file)
+static void intel_crtc_destroy(struct drm_crtc *crtc)
{
- drm_i915_private_t *dev_priv = dev->dev_private;
- struct drm_i915_get_pipe_from_crtc_id *pipe_from_crtc_id = data;
- struct drm_mode_object *drmmode_obj;
- struct intel_crtc *crtc;
-
- if (!dev_priv) {
- DRM_ERROR("called with no initialization\n");
- return -EINVAL;
- }
+ struct intel_crtc *intel_crtc = to_intel_crtc(crtc);
+ struct drm_device *dev = crtc->dev;
+ struct intel_unpin_work *work;
+ unsigned long flags;
- drmmode_obj = drm_mode_object_find(dev, pipe_from_crtc_id->crtc_id,
- DRM_MODE_OBJECT_CRTC);
+ spin_lock_irqsave(&dev->event_lock, flags);
+ work = intel_crtc->unpin_work;
+ intel_crtc->unpin_work = NULL;
+ spin_unlock_irqrestore(&dev->event_lock, flags);
- if (!drmmode_obj) {
- DRM_ERROR("no such CRTC id\n");
- return -EINVAL;
+ if (work) {
+ cancel_work_sync(&work->work);
+ kfree(work);
}
- crtc = to_intel_crtc(obj_to_crtc(drmmode_obj));
- pipe_from_crtc_id->pipe = crtc->pipe;
+ drm_crtc_cleanup(crtc);
- return 0;
+ kfree(intel_crtc);
}
-static int intel_encoder_clones(struct drm_device *dev, int type_mask)
+static void intel_unpin_work_fn(struct work_struct *__work)
{
- struct intel_encoder *encoder;
- int index_mask = 0;
- int entry = 0;
+ struct intel_unpin_work *work =
+ container_of(__work, struct intel_unpin_work, work);
- list_for_each_entry(encoder, &dev->mode_config.encoder_list, base.head) {
- if (type_mask & encoder->clone_mask)
- index_mask |= (1 << entry);
- entry++;
- }
+ mutex_lock(&work->dev->struct_mutex);
+ intel_unpin_fb_obj(work->old_fb_obj);
+ drm_gem_object_unreference(&work->pending_flip_obj->base);
+ drm_gem_object_unreference(&work->old_fb_obj->base);
- return index_mask;
+ intel_update_fbc(work->dev);
+ mutex_unlock(&work->dev->struct_mutex);
+ kfree(work);
}
-static bool has_edp_a(struct drm_device *dev)
+static void do_intel_finish_page_flip(struct drm_device *dev,
+ struct drm_crtc *crtc)
{
- struct drm_i915_private *dev_priv = dev->dev_private;
-
- if (!IS_MOBILE(dev))
- return false;
+ drm_i915_private_t *dev_priv = dev->dev_private;
+ struct intel_crtc *intel_crtc = to_intel_crtc(crtc);
+ struct intel_unpin_work *work;
+ struct drm_i915_gem_object *obj;
+ struct drm_pending_vblank_event *e;
+ struct timeval tnow, tvbl;
+ unsigned long flags;
- if ((I915_READ(DP_A) & DP_DETECTED) == 0)
- return false;
+ /* Ignore early vblank irqs */
+ if (intel_crtc == NULL)
+ return;
- if (IS_GEN5(dev) &&
- (I915_READ(ILK_DISPLAY_CHICKEN_FUSES) & ILK_eDP_A_DISABLE))
- return false;
+ do_gettimeofday(&tnow);
- return true;
-}
+ spin_lock_irqsave(&dev->event_lock, flags);
+ work = intel_crtc->unpin_work;
+ if (work == NULL || !work->pending) {
+ spin_unlock_irqrestore(&dev->event_lock, flags);
+ return;
+ }
-static void intel_setup_outputs(struct drm_device *dev)
-{
- struct drm_i915_private *dev_priv = dev->dev_private;
- struct intel_encoder *encoder;
- bool dpd_is_edp = false;
- bool has_lvds;
+ intel_crtc->unpin_work = NULL;
- has_lvds = intel_lvds_init(dev);
- if (!has_lvds && !HAS_PCH_SPLIT(dev)) {
- /* disable the panel fitter on everything but LVDS */
- I915_WRITE(PFIT_CONTROL, 0);
- }
+ if (work->event) {
+ e = work->event;
+ e->event.sequence = drm_vblank_count_and_time(dev, intel_crtc->pipe, &tvbl);
- if (HAS_PCH_SPLIT(dev)) {
- dpd_is_edp = intel_dpd_is_edp(dev);
+ /* Called before vblank count and timestamps have
+ * been updated for the vblank interval of flip
+ * completion? Need to increment vblank count and
+ * add one videorefresh duration to returned timestamp
+ * to account for this. We assume this happened if we
+ * get called over 0.9 frame durations after the last
+ * timestamped vblank.
+ *
+ * This calculation can not be used with vrefresh rates
+ * below 5Hz (10Hz to be on the safe side) without
+ * promoting to 64 integers.
+ */
+ if (10 * (timeval_to_ns(&tnow) - timeval_to_ns(&tvbl)) >
+ 9 * crtc->framedur_ns) {
+ e->event.sequence++;
+ tvbl = ns_to_timeval(timeval_to_ns(&tvbl) +
+ crtc->framedur_ns);
+ }
- if (has_edp_a(dev))
- intel_dp_init(dev, DP_A);
+ e->event.tv_sec = tvbl.tv_sec;
+ e->event.tv_usec = tvbl.tv_usec;
- if (dpd_is_edp && (I915_READ(PCH_DP_D) & DP_DETECTED))
- intel_dp_init(dev, PCH_DP_D);
+ list_add_tail(&e->base.link,
+ &e->base.file_priv->event_list);
+ wake_up_interruptible(&e->base.file_priv->event_wait);
}
- intel_crt_init(dev);
-
- if (HAS_PCH_SPLIT(dev)) {
- int found;
+ drm_vblank_put(dev, intel_crtc->pipe);
- if (I915_READ(HDMIB) & PORT_DETECTED) {
- /* PCH SDVOB multiplex with HDMIB */
- found = intel_sdvo_init(dev, PCH_SDVOB);
- if (!found)
- intel_hdmi_init(dev, HDMIB);
- if (!found && (I915_READ(PCH_DP_B) & DP_DETECTED))
- intel_dp_init(dev, PCH_DP_B);
- }
+ spin_unlock_irqrestore(&dev->event_lock, flags);
- if (I915_READ(HDMIC) & PORT_DETECTED)
- intel_hdmi_init(dev, HDMIC);
+ obj = work->old_fb_obj;
- if (I915_READ(HDMID) & PORT_DETECTED)
- intel_hdmi_init(dev, HDMID);
+ atomic_clear_mask(1 << intel_crtc->plane,
+ &obj->pending_flip.counter);
+ if (atomic_read(&obj->pending_flip) == 0)
+ wake_up(&dev_priv->pending_flip_queue);
- if (I915_READ(PCH_DP_C) & DP_DETECTED)
- intel_dp_init(dev, PCH_DP_C);
+ schedule_work(&work->work);
- if (!dpd_is_edp && (I915_READ(PCH_DP_D) & DP_DETECTED))
- intel_dp_init(dev, PCH_DP_D);
+ trace_i915_flip_complete(intel_crtc->plane, work->pending_flip_obj);
+}
- } else if (SUPPORTS_DIGITAL_OUTPUTS(dev)) {
- bool found = false;
+void intel_finish_page_flip(struct drm_device *dev, int pipe)
+{
+ drm_i915_private_t *dev_priv = dev->dev_private;
+ struct drm_crtc *crtc = dev_priv->pipe_to_crtc_mapping[pipe];
- if (I915_READ(SDVOB) & SDVO_DETECTED) {
- DRM_DEBUG_KMS("probing SDVOB\n");
- found = intel_sdvo_init(dev, SDVOB);
- if (!found && SUPPORTS_INTEGRATED_HDMI(dev)) {
- DRM_DEBUG_KMS("probing HDMI on SDVOB\n");
- intel_hdmi_init(dev, SDVOB);
- }
+ do_intel_finish_page_flip(dev, crtc);
+}
- if (!found && SUPPORTS_INTEGRATED_DP(dev)) {
- DRM_DEBUG_KMS("probing DP_B\n");
- intel_dp_init(dev, DP_B);
- }
- }
+void intel_finish_page_flip_plane(struct drm_device *dev, int plane)
+{
+ drm_i915_private_t *dev_priv = dev->dev_private;
+ struct drm_crtc *crtc = dev_priv->plane_to_crtc_mapping[plane];
- /* Before G4X SDVOC doesn't have its own detect register */
+ do_intel_finish_page_flip(dev, crtc);
+}
- if (I915_READ(SDVOB) & SDVO_DETECTED) {
- DRM_DEBUG_KMS("probing SDVOC\n");
- found = intel_sdvo_init(dev, SDVOC);
- }
+void intel_prepare_page_flip(struct drm_device *dev, int plane)
+{
+ drm_i915_private_t *dev_priv = dev->dev_private;
+ struct intel_crtc *intel_crtc =
+ to_intel_crtc(dev_priv->plane_to_crtc_mapping[plane]);
+ unsigned long flags;
- if (!found && (I915_READ(SDVOC) & SDVO_DETECTED)) {
+ spin_lock_irqsave(&dev->event_lock, flags);
+ if (intel_crtc->unpin_work) {
+ if ((++intel_crtc->unpin_work->pending) > 1)
+ DRM_ERROR("Prepared flip multiple times\n");
+ } else {
+ DRM_DEBUG_DRIVER("preparing flip with no unpin work?\n");
+ }
+ spin_unlock_irqrestore(&dev->event_lock, flags);
+}
- if (SUPPORTS_INTEGRATED_HDMI(dev)) {
- DRM_DEBUG_KMS("probing HDMI on SDVOC\n");
- intel_hdmi_init(dev, SDVOC);
- }
- if (SUPPORTS_INTEGRATED_DP(dev)) {
- DRM_DEBUG_KMS("probing DP_C\n");
- intel_dp_init(dev, DP_C);
- }
- }
+static int intel_gen2_queue_flip(struct drm_device *dev,
+ struct drm_crtc *crtc,
+ struct drm_framebuffer *fb,
+ struct drm_i915_gem_object *obj)
+{
+ struct drm_i915_private *dev_priv = dev->dev_private;
+ struct intel_crtc *intel_crtc = to_intel_crtc(crtc);
+ unsigned long offset;
+ u32 flip_mask;
+ int ret;
- if (SUPPORTS_INTEGRATED_DP(dev) &&
- (I915_READ(DP_D) & DP_DETECTED)) {
- DRM_DEBUG_KMS("probing DP_D\n");
- intel_dp_init(dev, DP_D);
- }
- } else if (IS_GEN2(dev))
- intel_dvo_init(dev);
+ ret = intel_pin_and_fence_fb_obj(dev, obj, LP_RING(dev_priv));
+ if (ret)
+ goto err;
- if (SUPPORTS_TV(dev))
- intel_tv_init(dev);
+ /* Offset into the new buffer for cases of shared fbs between CRTCs */
+ offset = crtc->y * fb->pitches[0] + crtc->x * fb->bits_per_pixel/8;
- list_for_each_entry(encoder, &dev->mode_config.encoder_list, base.head) {
- encoder->base.possible_crtcs = encoder->crtc_mask;
- encoder->base.possible_clones =
- intel_encoder_clones(dev, encoder->clone_mask);
- }
+ ret = BEGIN_LP_RING(6);
+ if (ret)
+ goto err_unpin;
- /* disable all the possible outputs/crtcs before entering KMS mode */
- drm_helper_disable_unused_functions(dev);
+ /* Can't queue multiple flips, so wait for the previous
+ * one to finish before executing the next.
+ */
+ if (intel_crtc->plane)
+ flip_mask = MI_WAIT_FOR_PLANE_B_FLIP;
+ else
+ flip_mask = MI_WAIT_FOR_PLANE_A_FLIP;
+ OUT_RING(MI_WAIT_FOR_EVENT | flip_mask);
+ OUT_RING(MI_NOOP);
+ OUT_RING(MI_DISPLAY_FLIP |
+ MI_DISPLAY_FLIP_PLANE(intel_crtc->plane));
+ OUT_RING(fb->pitches[0]);
+ OUT_RING(obj->gtt_offset + offset);
+ OUT_RING(0); /* aux display base address, unused */
+ ADVANCE_LP_RING();
+ return 0;
- if (HAS_PCH_SPLIT(dev))
- ironlake_init_pch_refclk(dev);
+err_unpin:
+ intel_unpin_fb_obj(obj);
+err:
+ return ret;
}
-static void intel_user_framebuffer_destroy(struct drm_framebuffer *fb)
+static int intel_gen3_queue_flip(struct drm_device *dev,
+ struct drm_crtc *crtc,
+ struct drm_framebuffer *fb,
+ struct drm_i915_gem_object *obj)
{
- struct intel_framebuffer *intel_fb = to_intel_framebuffer(fb);
+ struct drm_i915_private *dev_priv = dev->dev_private;
+ struct intel_crtc *intel_crtc = to_intel_crtc(crtc);
+ unsigned long offset;
+ u32 flip_mask;
+ int ret;
- drm_framebuffer_cleanup(fb);
- drm_gem_object_unreference_unlocked(&intel_fb->obj->base);
+ ret = intel_pin_and_fence_fb_obj(dev, obj, LP_RING(dev_priv));
+ if (ret)
+ goto err;
- kfree(intel_fb);
-}
+ /* Offset into the new buffer for cases of shared fbs between CRTCs */
+ offset = crtc->y * fb->pitches[0] + crtc->x * fb->bits_per_pixel/8;
-static int intel_user_framebuffer_create_handle(struct drm_framebuffer *fb,
- struct drm_file *file,
- unsigned int *handle)
-{
- struct intel_framebuffer *intel_fb = to_intel_framebuffer(fb);
- struct drm_i915_gem_object *obj = intel_fb->obj;
+ ret = BEGIN_LP_RING(6);
+ if (ret)
+ goto err_unpin;
- return drm_gem_handle_create(file, &obj->base, handle);
-}
+ if (intel_crtc->plane)
+ flip_mask = MI_WAIT_FOR_PLANE_B_FLIP;
+ else
+ flip_mask = MI_WAIT_FOR_PLANE_A_FLIP;
+ OUT_RING(MI_WAIT_FOR_EVENT | flip_mask);
+ OUT_RING(MI_NOOP);
+ OUT_RING(MI_DISPLAY_FLIP_I915 |
+ MI_DISPLAY_FLIP_PLANE(intel_crtc->plane));
+ OUT_RING(fb->pitches[0]);
+ OUT_RING(obj->gtt_offset + offset);
+ OUT_RING(MI_NOOP);
-static const struct drm_framebuffer_funcs intel_fb_funcs = {
- .destroy = intel_user_framebuffer_destroy,
- .create_handle = intel_user_framebuffer_create_handle,
-};
+ ADVANCE_LP_RING();
+ return 0;
-int intel_framebuffer_init(struct drm_device *dev,
- struct intel_framebuffer *intel_fb,
- struct drm_mode_fb_cmd2 *mode_cmd,
- struct drm_i915_gem_object *obj)
+err_unpin:
+ intel_unpin_fb_obj(obj);
+err:
+ return ret;
+}
+
+static int intel_gen4_queue_flip(struct drm_device *dev,
+ struct drm_crtc *crtc,
+ struct drm_framebuffer *fb,
+ struct drm_i915_gem_object *obj)
{
+ struct drm_i915_private *dev_priv = dev->dev_private;
+ struct intel_crtc *intel_crtc = to_intel_crtc(crtc);
+ uint32_t pf, pipesrc;
int ret;
- if (obj->tiling_mode == I915_TILING_Y)
- return -EINVAL;
-
- if (mode_cmd->pitches[0] & 63)
- return -EINVAL;
+ ret = intel_pin_and_fence_fb_obj(dev, obj, LP_RING(dev_priv));
+ if (ret)
+ goto err;
- switch (mode_cmd->pixel_format) {
- case DRM_FORMAT_RGB332:
- case DRM_FORMAT_RGB565:
- case DRM_FORMAT_XRGB8888:
- case DRM_FORMAT_XBGR8888:
- case DRM_FORMAT_ARGB8888:
- case DRM_FORMAT_XRGB2101010:
- case DRM_FORMAT_ARGB2101010:
- /* RGB formats are common across chipsets */
- break;
- case DRM_FORMAT_YUYV:
- case DRM_FORMAT_UYVY:
- case DRM_FORMAT_YVYU:
- case DRM_FORMAT_VYUY:
- break;
- default:
- DRM_DEBUG_KMS("unsupported pixel format %u\n",
- mode_cmd->pixel_format);
- return -EINVAL;
- }
+ ret = BEGIN_LP_RING(4);
+ if (ret)
+ goto err_unpin;
- ret = drm_framebuffer_init(dev, &intel_fb->base, &intel_fb_funcs);
- if (ret) {
- DRM_ERROR("framebuffer init failed %d\n", ret);
- return ret;
- }
+ /* i965+ uses the linear or tiled offsets from the
+ * Display Registers (which do not change across a page-flip)
+ * so we need only reprogram the base address.
+ */
+ OUT_RING(MI_DISPLAY_FLIP |
+ MI_DISPLAY_FLIP_PLANE(intel_crtc->plane));
+ OUT_RING(fb->pitches[0]);
+ OUT_RING(obj->gtt_offset | obj->tiling_mode);
- drm_helper_mode_fill_fb_struct(&intel_fb->base, mode_cmd);
- intel_fb->obj = obj;
+ /* XXX Enabling the panel-fitter across page-flip is so far
+ * untested on non-native modes, so ignore it for now.
+ * pf = I915_READ(pipe == 0 ? PFA_CTL_1 : PFB_CTL_1) & PF_ENABLE;
+ */
+ pf = 0;
+ pipesrc = I915_READ(PIPESRC(intel_crtc->pipe)) & 0x0fff0fff;
+ OUT_RING(pf | pipesrc);
+ ADVANCE_LP_RING();
return 0;
-}
-
-static struct drm_framebuffer *
-intel_user_framebuffer_create(struct drm_device *dev,
- struct drm_file *filp,
- struct drm_mode_fb_cmd2 *mode_cmd)
-{
- struct drm_i915_gem_object *obj;
- obj = to_intel_bo(drm_gem_object_lookup(dev, filp,
- mode_cmd->handles[0]));
- if (&obj->base == NULL)
- return ERR_PTR(-ENOENT);
-
- return intel_framebuffer_create(dev, mode_cmd, obj);
+err_unpin:
+ intel_unpin_fb_obj(obj);
+err:
+ return ret;
}
-static const struct drm_mode_config_funcs intel_mode_funcs = {
- .fb_create = intel_user_framebuffer_create,
- .output_poll_changed = intel_fb_output_poll_changed,
-};
-
-static struct drm_i915_gem_object *
-intel_alloc_context_page(struct drm_device *dev)
+static int intel_gen6_queue_flip(struct drm_device *dev,
+ struct drm_crtc *crtc,
+ struct drm_framebuffer *fb,
+ struct drm_i915_gem_object *obj)
{
- struct drm_i915_gem_object *ctx;
+ struct drm_i915_private *dev_priv = dev->dev_private;
+ struct intel_crtc *intel_crtc = to_intel_crtc(crtc);
+ uint32_t pf, pipesrc;
int ret;
- WARN_ON(!mutex_is_locked(&dev->struct_mutex));
-
- ctx = i915_gem_alloc_object(dev, 4096);
- if (!ctx) {
- DRM_DEBUG("failed to alloc power context, RC6 disabled\n");
- return NULL;
- }
-
- ret = i915_gem_object_pin(ctx, 4096, true);
- if (ret) {
- DRM_ERROR("failed to pin power context: %d\n", ret);
- goto err_unref;
- }
+ ret = intel_pin_and_fence_fb_obj(dev, obj, LP_RING(dev_priv));
+ if (ret)
+ goto err;
- ret = i915_gem_object_set_to_gtt_domain(ctx, 1);
- if (ret) {
- DRM_ERROR("failed to set-domain on power context: %d\n", ret);
+ ret = BEGIN_LP_RING(4);
+ if (ret)
goto err_unpin;
- }
- return ctx;
+ OUT_RING(MI_DISPLAY_FLIP |
+ MI_DISPLAY_FLIP_PLANE(intel_crtc->plane));
+ OUT_RING(fb->pitches[0] | obj->tiling_mode);
+ OUT_RING(obj->gtt_offset);
+
- pf = I915_READ(PF_CTL(intel_crtc->pipe)) & PF_ENABLE;
++ /* Contrary to the suggestions in the documentation,
++ * "Enable Panel Fitter" does not seem to be required when page
++ * flipping with a non-native mode, and worse causes a normal
++ * modeset to fail.
++ * pf = I915_READ(PF_CTL(intel_crtc->pipe)) & PF_ENABLE;
++ */
++ pf = 0;
+ pipesrc = I915_READ(PIPESRC(intel_crtc->pipe)) & 0x0fff0fff;
+ OUT_RING(pf | pipesrc);
+ ADVANCE_LP_RING();
+ return 0;
err_unpin:
- i915_gem_object_unpin(ctx);
-err_unref:
- drm_gem_object_unreference(&ctx->base);
- mutex_unlock(&dev->struct_mutex);
- return NULL;
+ intel_unpin_fb_obj(obj);
+err:
+ return ret;
}
-bool ironlake_set_drps(struct drm_device *dev, u8 val)
+/*
+ * On gen7 we currently use the blit ring because (in early silicon at least)
+ * the render ring doesn't give us interrpts for page flip completion, which
+ * means clients will hang after the first flip is queued. Fortunately the
+ * blit ring generates interrupts properly, so use it instead.
+ */
+static int intel_gen7_queue_flip(struct drm_device *dev,
+ struct drm_crtc *crtc,
+ struct drm_framebuffer *fb,
+ struct drm_i915_gem_object *obj)
{
struct drm_i915_private *dev_priv = dev->dev_private;
- u16 rgvswctl;
+ struct intel_crtc *intel_crtc = to_intel_crtc(crtc);
+ struct intel_ring_buffer *ring = &dev_priv->ring[BCS];
+ int ret;
- rgvswctl = I915_READ16(MEMSWCTL);
- if (rgvswctl & MEMCTL_CMD_STS) {
- DRM_DEBUG("gpu busy, RCS change rejected\n");
- return false; /* still busy with another command */
- }
+ ret = intel_pin_and_fence_fb_obj(dev, obj, ring);
+ if (ret)
+ goto err;
+
+ ret = intel_ring_begin(ring, 4);
+ if (ret)
+ goto err_unpin;
- rgvswctl = (MEMCTL_CMD_CHFREQ << MEMCTL_CMD_SHIFT) |
- (val << MEMCTL_FREQ_SHIFT) | MEMCTL_SFCAVM;
- I915_WRITE16(MEMSWCTL, rgvswctl);
- POSTING_READ16(MEMSWCTL);
+ intel_ring_emit(ring, MI_DISPLAY_FLIP_I915 | (intel_crtc->plane << 19));
+ intel_ring_emit(ring, (fb->pitches[0] | obj->tiling_mode));
+ intel_ring_emit(ring, (obj->gtt_offset));
+ intel_ring_emit(ring, (MI_NOOP));
+ intel_ring_advance(ring);
+ return 0;
- rgvswctl |= MEMCTL_CMD_STS;
- I915_WRITE16(MEMSWCTL, rgvswctl);
+err_unpin:
+ intel_unpin_fb_obj(obj);
+err:
+ return ret;
+}
- return true;
+static int intel_default_queue_flip(struct drm_device *dev,
+ struct drm_crtc *crtc,
+ struct drm_framebuffer *fb,
+ struct drm_i915_gem_object *obj)
+{
+ return -ENODEV;
}
-void ironlake_enable_drps(struct drm_device *dev)
+static int intel_crtc_page_flip(struct drm_crtc *crtc,
+ struct drm_framebuffer *fb,
+ struct drm_pending_vblank_event *event)
{
+ struct drm_device *dev = crtc->dev;
struct drm_i915_private *dev_priv = dev->dev_private;
- u32 rgvmodectl = I915_READ(MEMMODECTL);
- u8 fmax, fmin, fstart, vstart;
+ struct intel_framebuffer *intel_fb;
+ struct drm_i915_gem_object *obj;
+ struct intel_crtc *intel_crtc = to_intel_crtc(crtc);
+ struct intel_unpin_work *work;
+ unsigned long flags;
+ int ret;
+
+ work = kzalloc(sizeof *work, GFP_KERNEL);
+ if (work == NULL)
+ return -ENOMEM;
+
+ work->event = event;
+ work->dev = crtc->dev;
+ intel_fb = to_intel_framebuffer(crtc->fb);
+ work->old_fb_obj = intel_fb->obj;
+ INIT_WORK(&work->work, intel_unpin_work_fn);
+
+ ret = drm_vblank_get(dev, intel_crtc->pipe);
+ if (ret)
+ goto free_work;
+
+ /* We borrow the event spin lock for protecting unpin_work */
+ spin_lock_irqsave(&dev->event_lock, flags);
+ if (intel_crtc->unpin_work) {
+ spin_unlock_irqrestore(&dev->event_lock, flags);
+ kfree(work);
+ drm_vblank_put(dev, intel_crtc->pipe);
- /* Enable temp reporting */
- I915_WRITE16(PMMISC, I915_READ(PMMISC) | MCPPCE_EN);
- I915_WRITE16(TSC1, I915_READ(TSC1) | TSE);
+ DRM_DEBUG_DRIVER("flip queue: crtc already busy\n");
+ return -EBUSY;
+ }
+ intel_crtc->unpin_work = work;
+ spin_unlock_irqrestore(&dev->event_lock, flags);
- /* 100ms RC evaluation intervals */
- I915_WRITE(RCUPEI, 100000);
- I915_WRITE(RCDNEI, 100000);
+ intel_fb = to_intel_framebuffer(fb);
+ obj = intel_fb->obj;
- /* Set max/min thresholds to 90ms and 80ms respectively */
- I915_WRITE(RCBMAXAVG, 90000);
- I915_WRITE(RCBMINAVG, 80000);
+ mutex_lock(&dev->struct_mutex);
- I915_WRITE(MEMIHYST, 1);
+ /* Reference the objects for the scheduled work. */
+ drm_gem_object_reference(&work->old_fb_obj->base);
+ drm_gem_object_reference(&obj->base);
- /* Set up min, max, and cur for interrupt handling */
- fmax = (rgvmodectl & MEMMODE_FMAX_MASK) >> MEMMODE_FMAX_SHIFT;
- fmin = (rgvmodectl & MEMMODE_FMIN_MASK);
- fstart = (rgvmodectl & MEMMODE_FSTART_MASK) >>
- MEMMODE_FSTART_SHIFT;
+ crtc->fb = fb;
- vstart = (I915_READ(PXVFREQ_BASE + (fstart * 4)) & PXVFREQ_PX_MASK) >>
- PXVFREQ_PX_SHIFT;
+ work->pending_flip_obj = obj;
- dev_priv->fmax = fmax; /* IPS callback will increase this */
- dev_priv->fstart = fstart;
+ work->enable_stall_check = true;
- dev_priv->max_delay = fstart;
- dev_priv->min_delay = fmin;
- dev_priv->cur_delay = fstart;
+ /* Block clients from rendering to the new back buffer until
+ * the flip occurs and the object is no longer visible.
+ */
+ atomic_add(1 << intel_crtc->plane, &work->old_fb_obj->pending_flip);
- DRM_DEBUG_DRIVER("fmax: %d, fmin: %d, fstart: %d\n",
- fmax, fmin, fstart);
+ ret = dev_priv->display.queue_flip(dev, crtc, fb, obj);
+ if (ret)
+ goto cleanup_pending;
- I915_WRITE(MEMINTREN, MEMINT_CX_SUPR_EN | MEMINT_EVAL_CHG_EN);
+ intel_disable_fbc(dev);
+ mutex_unlock(&dev->struct_mutex);
- /*
- * Interrupts will be enabled in ironlake_irq_postinstall
- */
+ trace_i915_flip_request(intel_crtc->plane, obj);
- I915_WRITE(VIDSTART, vstart);
- POSTING_READ(VIDSTART);
+ return 0;
- rgvmodectl |= MEMMODE_SWMODE_EN;
- I915_WRITE(MEMMODECTL, rgvmodectl);
+cleanup_pending:
+ atomic_sub(1 << intel_crtc->plane, &work->old_fb_obj->pending_flip);
+ drm_gem_object_unreference(&work->old_fb_obj->base);
+ drm_gem_object_unreference(&obj->base);
+ mutex_unlock(&dev->struct_mutex);
- if (wait_for((I915_READ(MEMSWCTL) & MEMCTL_CMD_STS) == 0, 10))
- DRM_ERROR("stuck trying to change perf mode\n");
- msleep(1);
+ spin_lock_irqsave(&dev->event_lock, flags);
+ intel_crtc->unpin_work = NULL;
+ spin_unlock_irqrestore(&dev->event_lock, flags);
- ironlake_set_drps(dev, fstart);
+ drm_vblank_put(dev, intel_crtc->pipe);
+free_work:
+ kfree(work);
- dev_priv->last_count1 = I915_READ(0x112e4) + I915_READ(0x112e8) +
- I915_READ(0x112e0);
- dev_priv->last_time1 = jiffies_to_msecs(jiffies);
- dev_priv->last_count2 = I915_READ(0x112f4);
- getrawmonotonic(&dev_priv->last_time2);
+ return ret;
}
-void ironlake_disable_drps(struct drm_device *dev)
+static void intel_sanitize_modesetting(struct drm_device *dev,
+ int pipe, int plane)
{
struct drm_i915_private *dev_priv = dev->dev_private;
- u16 rgvswctl = I915_READ16(MEMSWCTL);
-
- /* Ack interrupts, disable EFC interrupt */
- I915_WRITE(MEMINTREN, I915_READ(MEMINTREN) & ~MEMINT_EVAL_CHG_EN);
- I915_WRITE(MEMINTRSTS, MEMINT_EVAL_CHG);
- I915_WRITE(DEIER, I915_READ(DEIER) & ~DE_PCU_EVENT);
- I915_WRITE(DEIIR, DE_PCU_EVENT);
- I915_WRITE(DEIMR, I915_READ(DEIMR) | DE_PCU_EVENT);
-
- /* Go back to the starting frequency */
- ironlake_set_drps(dev, dev_priv->fstart);
- msleep(1);
- rgvswctl |= MEMCTL_CMD_STS;
- I915_WRITE(MEMSWCTL, rgvswctl);
- msleep(1);
+ u32 reg, val;
-}
+ /* Clear any frame start delays used for debugging left by the BIOS */
+ for_each_pipe(pipe) {
+ reg = PIPECONF(pipe);
+ I915_WRITE(reg, I915_READ(reg) & ~PIPECONF_FRAME_START_DELAY_MASK);
+ }
-void gen6_set_rps(struct drm_device *dev, u8 val)
-{
- struct drm_i915_private *dev_priv = dev->dev_private;
- u32 swreq;
+ if (HAS_PCH_SPLIT(dev))
+ return;
- swreq = (val & 0x3ff) << 25;
- I915_WRITE(GEN6_RPNSWREQ, swreq);
-}
+ /* Who knows what state these registers were left in by the BIOS or
+ * grub?
+ *
+ * If we leave the registers in a conflicting state (e.g. with the
+ * display plane reading from the other pipe than the one we intend
+ * to use) then when we attempt to teardown the active mode, we will
+ * not disable the pipes and planes in the correct order -- leaving
+ * a plane reading from a disabled pipe and possibly leading to
+ * undefined behaviour.
+ */
-void gen6_disable_rps(struct drm_device *dev)
-{
- struct drm_i915_private *dev_priv = dev->dev_private;
+ reg = DSPCNTR(plane);
+ val = I915_READ(reg);
- I915_WRITE(GEN6_RPNSWREQ, 1 << 31);
- I915_WRITE(GEN6_PMINTRMSK, 0xffffffff);
- I915_WRITE(GEN6_PMIER, 0);
- /* Complete PM interrupt masking here doesn't race with the rps work
- * item again unmasking PM interrupts because that is using a different
- * register (PMIMR) to mask PM interrupts. The only risk is in leaving
- * stale bits in PMIIR and PMIMR which gen6_enable_rps will clean up. */
+ if ((val & DISPLAY_PLANE_ENABLE) == 0)
+ return;
+ if (!!(val & DISPPLANE_SEL_PIPE_MASK) == pipe)
+ return;
- spin_lock_irq(&dev_priv->rps_lock);
- dev_priv->pm_iir = 0;
- spin_unlock_irq(&dev_priv->rps_lock);
+ /* This display plane is active and attached to the other CPU pipe. */
+ pipe = !pipe;
- I915_WRITE(GEN6_PMIIR, I915_READ(GEN6_PMIIR));
+ /* Disable the plane and wait for it to stop reading from the pipe. */
+ intel_disable_plane(dev_priv, plane, pipe);
+ intel_disable_pipe(dev_priv, pipe);
}
-static unsigned long intel_pxfreq(u32 vidfreq)
+static void intel_crtc_reset(struct drm_crtc *crtc)
{
- unsigned long freq;
- int div = (vidfreq & 0x3f0000) >> 16;
- int post = (vidfreq & 0x3000) >> 12;
- int pre = (vidfreq & 0x7);
-
- if (!pre)
- return 0;
+ struct drm_device *dev = crtc->dev;
+ struct intel_crtc *intel_crtc = to_intel_crtc(crtc);
- freq = ((div * 133333) / ((1<<post) * pre));
+ /* Reset flags back to the 'unknown' status so that they
+ * will be correctly set on the initial modeset.
+ */
+ intel_crtc->dpms_mode = -1;
- return freq;
+ /* We need to fix up any BIOS configuration that conflicts with
+ * our expectations.
+ */
+ intel_sanitize_modesetting(dev, intel_crtc->pipe, intel_crtc->plane);
}
-void intel_init_emon(struct drm_device *dev)
+static struct drm_crtc_helper_funcs intel_helper_funcs = {
+ .dpms = intel_crtc_dpms,
+ .mode_fixup = intel_crtc_mode_fixup,
+ .mode_set = intel_crtc_mode_set,
+ .mode_set_base = intel_pipe_set_base,
+ .mode_set_base_atomic = intel_pipe_set_base_atomic,
+ .load_lut = intel_crtc_load_lut,
+ .disable = intel_crtc_disable,
+};
+
+static const struct drm_crtc_funcs intel_crtc_funcs = {
+ .reset = intel_crtc_reset,
+ .cursor_set = intel_crtc_cursor_set,
+ .cursor_move = intel_crtc_cursor_move,
+ .gamma_set = intel_crtc_gamma_set,
+ .set_config = drm_crtc_helper_set_config,
+ .destroy = intel_crtc_destroy,
+ .page_flip = intel_crtc_page_flip,
+};
+
+static void intel_crtc_init(struct drm_device *dev, int pipe)
{
- struct drm_i915_private *dev_priv = dev->dev_private;
- u32 lcfuse;
- u8 pxw[16];
+ drm_i915_private_t *dev_priv = dev->dev_private;
+ struct intel_crtc *intel_crtc;
int i;
- /* Disable to program */
- I915_WRITE(ECR, 0);
- POSTING_READ(ECR);
-
- /* Program energy weights for various events */
- I915_WRITE(SDEW, 0x15040d00);
- I915_WRITE(CSIEW0, 0x007f0000);
- I915_WRITE(CSIEW1, 0x1e220004);
- I915_WRITE(CSIEW2, 0x04000004);
-
- for (i = 0; i < 5; i++)
- I915_WRITE(PEW + (i * 4), 0);
- for (i = 0; i < 3; i++)
- I915_WRITE(DEW + (i * 4), 0);
-
- /* Program P-state weights to account for frequency power adjustment */
- for (i = 0; i < 16; i++) {
- u32 pxvidfreq = I915_READ(PXVFREQ_BASE + (i * 4));
- unsigned long freq = intel_pxfreq(pxvidfreq);
- unsigned long vid = (pxvidfreq & PXVFREQ_PX_MASK) >>
- PXVFREQ_PX_SHIFT;
- unsigned long val;
-
- val = vid * vid;
- val *= (freq / 1000);
- val *= 255;
- val /= (127*127*900);
- if (val > 0xff)
- DRM_ERROR("bad pxval: %ld\n", val);
- pxw[i] = val;
- }
- /* Render standby states get 0 weight */
- pxw[14] = 0;
- pxw[15] = 0;
+ intel_crtc = kzalloc(sizeof(struct intel_crtc) + (INTELFB_CONN_LIMIT * sizeof(struct drm_connector *)), GFP_KERNEL);
+ if (intel_crtc == NULL)
+ return;
- for (i = 0; i < 4; i++) {
- u32 val = (pxw[i*4] << 24) | (pxw[(i*4)+1] << 16) |
- (pxw[(i*4)+2] << 8) | (pxw[(i*4)+3]);
- I915_WRITE(PXW + (i * 4), val);
- }
+ drm_crtc_init(dev, &intel_crtc->base, &intel_crtc_funcs);
- /* Adjust magic regs to magic values (more experimental results) */
- I915_WRITE(OGW0, 0);
- I915_WRITE(OGW1, 0);
- I915_WRITE(EG0, 0x00007f00);
- I915_WRITE(EG1, 0x0000000e);
- I915_WRITE(EG2, 0x000e0000);
- I915_WRITE(EG3, 0x68000300);
- I915_WRITE(EG4, 0x42000000);
- I915_WRITE(EG5, 0x00140031);
- I915_WRITE(EG6, 0);
- I915_WRITE(EG7, 0);
+ drm_mode_crtc_set_gamma_size(&intel_crtc->base, 256);
+ for (i = 0; i < 256; i++) {
+ intel_crtc->lut_r[i] = i;
+ intel_crtc->lut_g[i] = i;
+ intel_crtc->lut_b[i] = i;
+ }
- for (i = 0; i < 8; i++)
- I915_WRITE(PXWL + (i * 4), 0);
+ /* Swap pipes & planes for FBC on pre-965 */
+ intel_crtc->pipe = pipe;
+ intel_crtc->plane = pipe;
+ if (IS_MOBILE(dev) && IS_GEN3(dev)) {
+ DRM_DEBUG_KMS("swapping pipes & planes for FBC\n");
+ intel_crtc->plane = !pipe;
+ }
- /* Enable PMON + select events */
- I915_WRITE(ECR, 0x80000019);
+ BUG_ON(pipe >= ARRAY_SIZE(dev_priv->plane_to_crtc_mapping) ||
+ dev_priv->plane_to_crtc_mapping[intel_crtc->plane] != NULL);
+ dev_priv->plane_to_crtc_mapping[intel_crtc->plane] = &intel_crtc->base;
+ dev_priv->pipe_to_crtc_mapping[intel_crtc->pipe] = &intel_crtc->base;
- lcfuse = I915_READ(LCFUSE02);
+ intel_crtc_reset(&intel_crtc->base);
+ intel_crtc->active = true; /* force the pipe off on setup_init_config */
+ intel_crtc->bpp = 24; /* default for pre-Ironlake */
- dev_priv->corr = (lcfuse & LCFUSE_HIV_MASK);
-}
+ if (HAS_PCH_SPLIT(dev)) {
+ if (pipe == 2 && IS_IVYBRIDGE(dev))
+ intel_crtc->no_pll = true;
+ intel_helper_funcs.prepare = ironlake_crtc_prepare;
+ intel_helper_funcs.commit = ironlake_crtc_commit;
+ } else {
+ intel_helper_funcs.prepare = i9xx_crtc_prepare;
+ intel_helper_funcs.commit = i9xx_crtc_commit;
+ }
-static int intel_enable_rc6(struct drm_device *dev)
-{
- /*
- * Respect the kernel parameter if it is set
- */
- if (i915_enable_rc6 >= 0)
- return i915_enable_rc6;
+ drm_crtc_helper_add(&intel_crtc->base, &intel_helper_funcs);
- /*
- * Disable RC6 on Ironlake
- */
- if (INTEL_INFO(dev)->gen == 5)
- return 0;
+ intel_crtc->busy = false;
- /*
- * Disable rc6 on Sandybridge
- */
- if (INTEL_INFO(dev)->gen == 6) {
- DRM_DEBUG_DRIVER("Sandybridge: deep RC6 disabled\n");
- return INTEL_RC6_ENABLE;
- }
- DRM_DEBUG_DRIVER("RC6 and deep RC6 enabled\n");
- return (INTEL_RC6_ENABLE | INTEL_RC6p_ENABLE);
+ setup_timer(&intel_crtc->idle_timer, intel_crtc_idle_timer,
+ (unsigned long)intel_crtc);
}
-void gen6_enable_rps(struct drm_i915_private *dev_priv)
+int intel_get_pipe_from_crtc_id(struct drm_device *dev, void *data,
+ struct drm_file *file)
{
- u32 rp_state_cap = I915_READ(GEN6_RP_STATE_CAP);
- u32 gt_perf_status = I915_READ(GEN6_GT_PERF_STATUS);
- u32 pcu_mbox, rc6_mask = 0;
- u32 gtfifodbg;
- int cur_freq, min_freq, max_freq;
- int rc6_mode;
- int i;
-
- /* Here begins a magic sequence of register writes to enable
- * auto-downclocking.
- *
- * Perhaps there might be some value in exposing these to
- * userspace...
- */
- I915_WRITE(GEN6_RC_STATE, 0);
- mutex_lock(&dev_priv->dev->struct_mutex);
-
- /* Clear the DBG now so we don't confuse earlier errors */
- if ((gtfifodbg = I915_READ(GTFIFODBG))) {
- DRM_ERROR("GT fifo had a previous error %x\n", gtfifodbg);
- I915_WRITE(GTFIFODBG, gtfifodbg);
- }
-
- gen6_gt_force_wake_get(dev_priv);
-
- /* disable the counters and set deterministic thresholds */
- I915_WRITE(GEN6_RC_CONTROL, 0);
-
- I915_WRITE(GEN6_RC1_WAKE_RATE_LIMIT, 1000 << 16);
- I915_WRITE(GEN6_RC6_WAKE_RATE_LIMIT, 40 << 16 | 30);
- I915_WRITE(GEN6_RC6pp_WAKE_RATE_LIMIT, 30);
- I915_WRITE(GEN6_RC_EVALUATION_INTERVAL, 125000);
- I915_WRITE(GEN6_RC_IDLE_HYSTERSIS, 25);
-
- for (i = 0; i < I915_NUM_RINGS; i++)
- I915_WRITE(RING_MAX_IDLE(dev_priv->ring[i].mmio_base), 10);
-
- I915_WRITE(GEN6_RC_SLEEP, 0);
- I915_WRITE(GEN6_RC1e_THRESHOLD, 1000);
- I915_WRITE(GEN6_RC6_THRESHOLD, 50000);
- I915_WRITE(GEN6_RC6p_THRESHOLD, 100000);
- I915_WRITE(GEN6_RC6pp_THRESHOLD, 64000); /* unused */
-
- rc6_mode = intel_enable_rc6(dev_priv->dev);
- if (rc6_mode & INTEL_RC6_ENABLE)
- rc6_mask |= GEN6_RC_CTL_RC6_ENABLE;
-
- if (rc6_mode & INTEL_RC6p_ENABLE)
- rc6_mask |= GEN6_RC_CTL_RC6p_ENABLE;
-
- if (rc6_mode & INTEL_RC6pp_ENABLE)
- rc6_mask |= GEN6_RC_CTL_RC6pp_ENABLE;
-
- DRM_INFO("Enabling RC6 states: RC6 %s, RC6p %s, RC6pp %s\n",
- (rc6_mode & INTEL_RC6_ENABLE) ? "on" : "off",
- (rc6_mode & INTEL_RC6p_ENABLE) ? "on" : "off",
- (rc6_mode & INTEL_RC6pp_ENABLE) ? "on" : "off");
-
- I915_WRITE(GEN6_RC_CONTROL,
- rc6_mask |
- GEN6_RC_CTL_EI_MODE(1) |
- GEN6_RC_CTL_HW_ENABLE);
-
- I915_WRITE(GEN6_RPNSWREQ,
- GEN6_FREQUENCY(10) |
- GEN6_OFFSET(0) |
- GEN6_AGGRESSIVE_TURBO);
- I915_WRITE(GEN6_RC_VIDEO_FREQ,
- GEN6_FREQUENCY(12));
-
- I915_WRITE(GEN6_RP_DOWN_TIMEOUT, 1000000);
- I915_WRITE(GEN6_RP_INTERRUPT_LIMITS,
- 18 << 24 |
- 6 << 16);
- I915_WRITE(GEN6_RP_UP_THRESHOLD, 10000);
- I915_WRITE(GEN6_RP_DOWN_THRESHOLD, 1000000);
- I915_WRITE(GEN6_RP_UP_EI, 100000);
- I915_WRITE(GEN6_RP_DOWN_EI, 5000000);
- I915_WRITE(GEN6_RP_IDLE_HYSTERSIS, 10);
- I915_WRITE(GEN6_RP_CONTROL,
- GEN6_RP_MEDIA_TURBO |
- GEN6_RP_MEDIA_HW_MODE |
- GEN6_RP_MEDIA_IS_GFX |
- GEN6_RP_ENABLE |
- GEN6_RP_UP_BUSY_AVG |
- GEN6_RP_DOWN_IDLE_CONT);
-
- if (wait_for((I915_READ(GEN6_PCODE_MAILBOX) & GEN6_PCODE_READY) == 0,
- 500))
- DRM_ERROR("timeout waiting for pcode mailbox to become idle\n");
-
- I915_WRITE(GEN6_PCODE_DATA, 0);
- I915_WRITE(GEN6_PCODE_MAILBOX,
- GEN6_PCODE_READY |
- GEN6_PCODE_WRITE_MIN_FREQ_TABLE);
- if (wait_for((I915_READ(GEN6_PCODE_MAILBOX) & GEN6_PCODE_READY) == 0,
- 500))
- DRM_ERROR("timeout waiting for pcode mailbox to finish\n");
-
- min_freq = (rp_state_cap & 0xff0000) >> 16;
- max_freq = rp_state_cap & 0xff;
- cur_freq = (gt_perf_status & 0xff00) >> 8;
-
- /* Check for overclock support */
- if (wait_for((I915_READ(GEN6_PCODE_MAILBOX) & GEN6_PCODE_READY) == 0,
- 500))
- DRM_ERROR("timeout waiting for pcode mailbox to become idle\n");
- I915_WRITE(GEN6_PCODE_MAILBOX, GEN6_READ_OC_PARAMS);
- pcu_mbox = I915_READ(GEN6_PCODE_DATA);
- if (wait_for((I915_READ(GEN6_PCODE_MAILBOX) & GEN6_PCODE_READY) == 0,
- 500))
- DRM_ERROR("timeout waiting for pcode mailbox to finish\n");
- if (pcu_mbox & (1<<31)) { /* OC supported */
- max_freq = pcu_mbox & 0xff;
- DRM_DEBUG_DRIVER("overclocking supported, adjusting frequency max to %dMHz\n", pcu_mbox * 50);
- }
-
- /* In units of 100MHz */
- dev_priv->max_delay = max_freq;
- dev_priv->min_delay = min_freq;
- dev_priv->cur_delay = cur_freq;
-
- /* requires MSI enabled */
- I915_WRITE(GEN6_PMIER,
- GEN6_PM_MBOX_EVENT |
- GEN6_PM_THERMAL_EVENT |
- GEN6_PM_RP_DOWN_TIMEOUT |
- GEN6_PM_RP_UP_THRESHOLD |
- GEN6_PM_RP_DOWN_THRESHOLD |
- GEN6_PM_RP_UP_EI_EXPIRED |
- GEN6_PM_RP_DOWN_EI_EXPIRED);
- spin_lock_irq(&dev_priv->rps_lock);
- WARN_ON(dev_priv->pm_iir != 0);
- I915_WRITE(GEN6_PMIMR, 0);
- spin_unlock_irq(&dev_priv->rps_lock);
- /* enable all PM interrupts */
- I915_WRITE(GEN6_PMINTRMSK, 0);
-
- gen6_gt_force_wake_put(dev_priv);
- mutex_unlock(&dev_priv->dev->struct_mutex);
-}
-
-void gen6_update_ring_freq(struct drm_i915_private *dev_priv)
-{
- int min_freq = 15;
- int gpu_freq, ia_freq, max_ia_freq;
- int scaling_factor = 180;
-
- max_ia_freq = cpufreq_quick_get_max(0);
- /*
- * Default to measured freq if none found, PCU will ensure we don't go
- * over
- */
- if (!max_ia_freq)
- max_ia_freq = tsc_khz;
-
- /* Convert from kHz to MHz */
- max_ia_freq /= 1000;
+ drm_i915_private_t *dev_priv = dev->dev_private;
+ struct drm_i915_get_pipe_from_crtc_id *pipe_from_crtc_id = data;
+ struct drm_mode_object *drmmode_obj;
+ struct intel_crtc *crtc;
- mutex_lock(&dev_priv->dev->struct_mutex);
+ if (!dev_priv) {
+ DRM_ERROR("called with no initialization\n");
+ return -EINVAL;
+ }
- /*
- * For each potential GPU frequency, load a ring frequency we'd like
- * to use for memory access. We do this by specifying the IA frequency
- * the PCU should use as a reference to determine the ring frequency.
- */
- for (gpu_freq = dev_priv->max_delay; gpu_freq >= dev_priv->min_delay;
- gpu_freq--) {
- int diff = dev_priv->max_delay - gpu_freq;
+ drmmode_obj = drm_mode_object_find(dev, pipe_from_crtc_id->crtc_id,
+ DRM_MODE_OBJECT_CRTC);
- /*
- * For GPU frequencies less than 750MHz, just use the lowest
- * ring freq.
- */
- if (gpu_freq < min_freq)
- ia_freq = 800;
- else
- ia_freq = max_ia_freq - ((diff * scaling_factor) / 2);
- ia_freq = DIV_ROUND_CLOSEST(ia_freq, 100);
-
- I915_WRITE(GEN6_PCODE_DATA,
- (ia_freq << GEN6_PCODE_FREQ_IA_RATIO_SHIFT) |
- gpu_freq);
- I915_WRITE(GEN6_PCODE_MAILBOX, GEN6_PCODE_READY |
- GEN6_PCODE_WRITE_MIN_FREQ_TABLE);
- if (wait_for((I915_READ(GEN6_PCODE_MAILBOX) &
- GEN6_PCODE_READY) == 0, 10)) {
- DRM_ERROR("pcode write of freq table timed out\n");
- continue;
- }
+ if (!drmmode_obj) {
+ DRM_ERROR("no such CRTC id\n");
+ return -EINVAL;
}
- mutex_unlock(&dev_priv->dev->struct_mutex);
+ crtc = to_intel_crtc(obj_to_crtc(drmmode_obj));
+ pipe_from_crtc_id->pipe = crtc->pipe;
+
+ return 0;
}
-static void ironlake_init_clock_gating(struct drm_device *dev)
+static int intel_encoder_clones(struct drm_device *dev, int type_mask)
{
- struct drm_i915_private *dev_priv = dev->dev_private;
- uint32_t dspclk_gate = VRHUNIT_CLOCK_GATE_DISABLE;
-
- /* Required for FBC */
- dspclk_gate |= DPFCUNIT_CLOCK_GATE_DISABLE |
- DPFCRUNIT_CLOCK_GATE_DISABLE |
- DPFDUNIT_CLOCK_GATE_DISABLE;
- /* Required for CxSR */
- dspclk_gate |= DPARBUNIT_CLOCK_GATE_DISABLE;
-
- I915_WRITE(PCH_3DCGDIS0,
- MARIUNIT_CLOCK_GATE_DISABLE |
- SVSMUNIT_CLOCK_GATE_DISABLE);
- I915_WRITE(PCH_3DCGDIS1,
- VFMUNIT_CLOCK_GATE_DISABLE);
-
- I915_WRITE(PCH_DSPCLK_GATE_D, dspclk_gate);
-
- /*
- * According to the spec the following bits should be set in
- * order to enable memory self-refresh
- * The bit 22/21 of 0x42004
- * The bit 5 of 0x42020
- * The bit 15 of 0x45000
- */
- I915_WRITE(ILK_DISPLAY_CHICKEN2,
- (I915_READ(ILK_DISPLAY_CHICKEN2) |
- ILK_DPARB_GATE | ILK_VSDPFD_FULL));
- I915_WRITE(ILK_DSPCLK_GATE,
- (I915_READ(ILK_DSPCLK_GATE) |
- ILK_DPARB_CLK_GATE));
- I915_WRITE(DISP_ARB_CTL,
- (I915_READ(DISP_ARB_CTL) |
- DISP_FBC_WM_DIS));
- I915_WRITE(WM3_LP_ILK, 0);
- I915_WRITE(WM2_LP_ILK, 0);
- I915_WRITE(WM1_LP_ILK, 0);
+ struct intel_encoder *encoder;
+ int index_mask = 0;
+ int entry = 0;
- /*
- * Based on the document from hardware guys the following bits
- * should be set unconditionally in order to enable FBC.
- * The bit 22 of 0x42000
- * The bit 22 of 0x42004
- * The bit 7,8,9 of 0x42020.
- */
- if (IS_IRONLAKE_M(dev)) {
- I915_WRITE(ILK_DISPLAY_CHICKEN1,
- I915_READ(ILK_DISPLAY_CHICKEN1) |
- ILK_FBCQ_DIS);
- I915_WRITE(ILK_DISPLAY_CHICKEN2,
- I915_READ(ILK_DISPLAY_CHICKEN2) |
- ILK_DPARB_GATE);
- I915_WRITE(ILK_DSPCLK_GATE,
- I915_READ(ILK_DSPCLK_GATE) |
- ILK_DPFC_DIS1 |
- ILK_DPFC_DIS2 |
- ILK_CLK_FBC);
+ list_for_each_entry(encoder, &dev->mode_config.encoder_list, base.head) {
+ if (type_mask & encoder->clone_mask)
+ index_mask |= (1 << entry);
+ entry++;
}
- I915_WRITE(ILK_DISPLAY_CHICKEN2,
- I915_READ(ILK_DISPLAY_CHICKEN2) |
- ILK_ELPIN_409_SELECT);
- I915_WRITE(_3D_CHICKEN2,
- _3D_CHICKEN2_WM_READ_PIPELINED << 16 |
- _3D_CHICKEN2_WM_READ_PIPELINED);
+ return index_mask;
}
-static void gen6_init_clock_gating(struct drm_device *dev)
+static bool has_edp_a(struct drm_device *dev)
{
struct drm_i915_private *dev_priv = dev->dev_private;
- int pipe;
- uint32_t dspclk_gate = VRHUNIT_CLOCK_GATE_DISABLE;
-
- I915_WRITE(PCH_DSPCLK_GATE_D, dspclk_gate);
-
- I915_WRITE(ILK_DISPLAY_CHICKEN2,
- I915_READ(ILK_DISPLAY_CHICKEN2) |
- ILK_ELPIN_409_SELECT);
- I915_WRITE(WM3_LP_ILK, 0);
- I915_WRITE(WM2_LP_ILK, 0);
- I915_WRITE(WM1_LP_ILK, 0);
-
- I915_WRITE(GEN6_UCGCTL1,
- I915_READ(GEN6_UCGCTL1) |
- GEN6_BLBUNIT_CLOCK_GATE_DISABLE);
+ if (!IS_MOBILE(dev))
+ return false;
- /* According to the BSpec vol1g, bit 12 (RCPBUNIT) clock
- * gating disable must be set. Failure to set it results in
- * flickering pixels due to Z write ordering failures after
- * some amount of runtime in the Mesa "fire" demo, and Unigine
- * Sanctuary and Tropics, and apparently anything else with
- * alpha test or pixel discard.
- *
- * According to the spec, bit 11 (RCCUNIT) must also be set,
- * but we didn't debug actual testcases to find it out.
- */
- I915_WRITE(GEN6_UCGCTL2,
- GEN6_RCPBUNIT_CLOCK_GATE_DISABLE |
- GEN6_RCCUNIT_CLOCK_GATE_DISABLE);
+ if ((I915_READ(DP_A) & DP_DETECTED) == 0)
+ return false;
- /*
- * According to the spec the following bits should be
- * set in order to enable memory self-refresh and fbc:
- * The bit21 and bit22 of 0x42000
- * The bit21 and bit22 of 0x42004
- * The bit5 and bit7 of 0x42020
- * The bit14 of 0x70180
- * The bit14 of 0x71180
- */
- I915_WRITE(ILK_DISPLAY_CHICKEN1,
- I915_READ(ILK_DISPLAY_CHICKEN1) |
- ILK_FBCQ_DIS | ILK_PABSTRETCH_DIS);
- I915_WRITE(ILK_DISPLAY_CHICKEN2,
- I915_READ(ILK_DISPLAY_CHICKEN2) |
- ILK_DPARB_GATE | ILK_VSDPFD_FULL);
- I915_WRITE(ILK_DSPCLK_GATE,
- I915_READ(ILK_DSPCLK_GATE) |
- ILK_DPARB_CLK_GATE |
- ILK_DPFD_CLK_GATE);
+ if (IS_GEN5(dev) &&
+ (I915_READ(ILK_DISPLAY_CHICKEN_FUSES) & ILK_eDP_A_DISABLE))
+ return false;
- for_each_pipe(pipe) {
- I915_WRITE(DSPCNTR(pipe),
- I915_READ(DSPCNTR(pipe)) |
- DISPPLANE_TRICKLE_FEED_DISABLE);
- intel_flush_display_plane(dev_priv, pipe);
- }
+ return true;
}
-static void ivybridge_init_clock_gating(struct drm_device *dev)
+static void intel_setup_outputs(struct drm_device *dev)
{
struct drm_i915_private *dev_priv = dev->dev_private;
- int pipe;
- uint32_t dspclk_gate = VRHUNIT_CLOCK_GATE_DISABLE;
-
- I915_WRITE(PCH_DSPCLK_GATE_D, dspclk_gate);
-
- I915_WRITE(WM3_LP_ILK, 0);
- I915_WRITE(WM2_LP_ILK, 0);
- I915_WRITE(WM1_LP_ILK, 0);
-
- /* According to the spec, bit 13 (RCZUNIT) must be set on IVB.
- * This implements the WaDisableRCZUnitClockGating workaround.
- */
- I915_WRITE(GEN6_UCGCTL2, GEN6_RCZUNIT_CLOCK_GATE_DISABLE);
-
- I915_WRITE(ILK_DSPCLK_GATE, IVB_VRHUNIT_CLK_GATE);
-
- I915_WRITE(IVB_CHICKEN3,
- CHICKEN3_DGMG_REQ_OUT_FIX_DISABLE |
- CHICKEN3_DGMG_DONE_FIX_DISABLE);
-
- /* Apply the WaDisableRHWOOptimizationForRenderHang workaround. */
- I915_WRITE(GEN7_COMMON_SLICE_CHICKEN1,
- GEN7_CSC1_RHWO_OPT_DISABLE_IN_RCC);
+ struct intel_encoder *encoder;
+ bool dpd_is_edp = false;
+ bool has_lvds;
- /* WaApplyL3ControlAndL3ChickenMode requires those two on Ivy Bridge */
- I915_WRITE(GEN7_L3CNTLREG1,
- GEN7_WA_FOR_GEN7_L3_CONTROL);
- I915_WRITE(GEN7_L3_CHICKEN_MODE_REGISTER,
- GEN7_WA_L3_CHICKEN_MODE);
+ has_lvds = intel_lvds_init(dev);
+ if (!has_lvds && !HAS_PCH_SPLIT(dev)) {
+ /* disable the panel fitter on everything but LVDS */
+ I915_WRITE(PFIT_CONTROL, 0);
+ }
- /* This is required by WaCatErrorRejectionIssue */
- I915_WRITE(GEN7_SQ_CHICKEN_MBCUNIT_CONFIG,
- I915_READ(GEN7_SQ_CHICKEN_MBCUNIT_CONFIG) |
- GEN7_SQ_CHICKEN_MBCUNIT_SQINTMOB);
+ if (HAS_PCH_SPLIT(dev)) {
+ dpd_is_edp = intel_dpd_is_edp(dev);
- for_each_pipe(pipe) {
- I915_WRITE(DSPCNTR(pipe),
- I915_READ(DSPCNTR(pipe)) |
- DISPPLANE_TRICKLE_FEED_DISABLE);
- intel_flush_display_plane(dev_priv, pipe);
- }
-}
+ if (has_edp_a(dev))
+ intel_dp_init(dev, DP_A);
-static void g4x_init_clock_gating(struct drm_device *dev)
-{
- struct drm_i915_private *dev_priv = dev->dev_private;
- uint32_t dspclk_gate;
+ if (dpd_is_edp && (I915_READ(PCH_DP_D) & DP_DETECTED))
+ intel_dp_init(dev, PCH_DP_D);
+ }
- I915_WRITE(RENCLK_GATE_D1, 0);
- I915_WRITE(RENCLK_GATE_D2, VF_UNIT_CLOCK_GATE_DISABLE |
- GS_UNIT_CLOCK_GATE_DISABLE |
- CL_UNIT_CLOCK_GATE_DISABLE);
- I915_WRITE(RAMCLK_GATE_D, 0);
- dspclk_gate = VRHUNIT_CLOCK_GATE_DISABLE |
- OVRUNIT_CLOCK_GATE_DISABLE |
- OVCUNIT_CLOCK_GATE_DISABLE;
- if (IS_GM45(dev))
- dspclk_gate |= DSSUNIT_CLOCK_GATE_DISABLE;
- I915_WRITE(DSPCLK_GATE_D, dspclk_gate);
-}
+ intel_crt_init(dev);
-static void crestline_init_clock_gating(struct drm_device *dev)
-{
- struct drm_i915_private *dev_priv = dev->dev_private;
+ if (HAS_PCH_SPLIT(dev)) {
+ int found;
- I915_WRITE(RENCLK_GATE_D1, I965_RCC_CLOCK_GATE_DISABLE);
- I915_WRITE(RENCLK_GATE_D2, 0);
- I915_WRITE(DSPCLK_GATE_D, 0);
- I915_WRITE(RAMCLK_GATE_D, 0);
- I915_WRITE16(DEUC, 0);
-}
+ if (I915_READ(HDMIB) & PORT_DETECTED) {
+ /* PCH SDVOB multiplex with HDMIB */
+ found = intel_sdvo_init(dev, PCH_SDVOB, true);
+ if (!found)
+ intel_hdmi_init(dev, HDMIB);
+ if (!found && (I915_READ(PCH_DP_B) & DP_DETECTED))
+ intel_dp_init(dev, PCH_DP_B);
+ }
-static void broadwater_init_clock_gating(struct drm_device *dev)
-{
- struct drm_i915_private *dev_priv = dev->dev_private;
+ if (I915_READ(HDMIC) & PORT_DETECTED)
+ intel_hdmi_init(dev, HDMIC);
- I915_WRITE(RENCLK_GATE_D1, I965_RCZ_CLOCK_GATE_DISABLE |
- I965_RCC_CLOCK_GATE_DISABLE |
- I965_RCPB_CLOCK_GATE_DISABLE |
- I965_ISC_CLOCK_GATE_DISABLE |
- I965_FBC_CLOCK_GATE_DISABLE);
- I915_WRITE(RENCLK_GATE_D2, 0);
-}
+ if (I915_READ(HDMID) & PORT_DETECTED)
+ intel_hdmi_init(dev, HDMID);
-static void gen3_init_clock_gating(struct drm_device *dev)
-{
- struct drm_i915_private *dev_priv = dev->dev_private;
- u32 dstate = I915_READ(D_STATE);
+ if (I915_READ(PCH_DP_C) & DP_DETECTED)
+ intel_dp_init(dev, PCH_DP_C);
- dstate |= DSTATE_PLL_D3_OFF | DSTATE_GFX_CLOCK_GATING |
- DSTATE_DOT_CLOCK_GATING;
- I915_WRITE(D_STATE, dstate);
-}
+ if (!dpd_is_edp && (I915_READ(PCH_DP_D) & DP_DETECTED))
+ intel_dp_init(dev, PCH_DP_D);
-static void i85x_init_clock_gating(struct drm_device *dev)
-{
- struct drm_i915_private *dev_priv = dev->dev_private;
+ } else if (SUPPORTS_DIGITAL_OUTPUTS(dev)) {
+ bool found = false;
- I915_WRITE(RENCLK_GATE_D1, SV_CLOCK_GATE_DISABLE);
-}
+ if (I915_READ(SDVOB) & SDVO_DETECTED) {
+ DRM_DEBUG_KMS("probing SDVOB\n");
+ found = intel_sdvo_init(dev, SDVOB, true);
+ if (!found && SUPPORTS_INTEGRATED_HDMI(dev)) {
+ DRM_DEBUG_KMS("probing HDMI on SDVOB\n");
+ intel_hdmi_init(dev, SDVOB);
+ }
-static void i830_init_clock_gating(struct drm_device *dev)
-{
- struct drm_i915_private *dev_priv = dev->dev_private;
+ if (!found && SUPPORTS_INTEGRATED_DP(dev)) {
+ DRM_DEBUG_KMS("probing DP_B\n");
+ intel_dp_init(dev, DP_B);
+ }
+ }
- I915_WRITE(DSPCLK_GATE_D, OVRUNIT_CLOCK_GATE_DISABLE);
-}
+ /* Before G4X SDVOC doesn't have its own detect register */
-static void ibx_init_clock_gating(struct drm_device *dev)
-{
- struct drm_i915_private *dev_priv = dev->dev_private;
+ if (I915_READ(SDVOB) & SDVO_DETECTED) {
+ DRM_DEBUG_KMS("probing SDVOC\n");
+ found = intel_sdvo_init(dev, SDVOC, false);
+ }
- /*
- * On Ibex Peak and Cougar Point, we need to disable clock
- * gating for the panel power sequencer or it will fail to
- * start up when no ports are active.
- */
- I915_WRITE(SOUTH_DSPCLK_GATE_D, PCH_DPLSUNIT_CLOCK_GATE_DISABLE);
-}
+ if (!found && (I915_READ(SDVOC) & SDVO_DETECTED)) {
-static void cpt_init_clock_gating(struct drm_device *dev)
-{
- struct drm_i915_private *dev_priv = dev->dev_private;
- int pipe;
+ if (SUPPORTS_INTEGRATED_HDMI(dev)) {
+ DRM_DEBUG_KMS("probing HDMI on SDVOC\n");
+ intel_hdmi_init(dev, SDVOC);
+ }
+ if (SUPPORTS_INTEGRATED_DP(dev)) {
+ DRM_DEBUG_KMS("probing DP_C\n");
+ intel_dp_init(dev, DP_C);
+ }
+ }
- /*
- * On Ibex Peak and Cougar Point, we need to disable clock
- * gating for the panel power sequencer or it will fail to
- * start up when no ports are active.
- */
- I915_WRITE(SOUTH_DSPCLK_GATE_D, PCH_DPLSUNIT_CLOCK_GATE_DISABLE);
- I915_WRITE(SOUTH_CHICKEN2, I915_READ(SOUTH_CHICKEN2) |
- DPLS_EDP_PPS_FIX_DIS);
- /* Without this, mode sets may fail silently on FDI */
- for_each_pipe(pipe)
- I915_WRITE(TRANS_CHICKEN2(pipe), TRANS_AUTOTRAIN_GEN_STALL_DIS);
-}
+ if (SUPPORTS_INTEGRATED_DP(dev) &&
+ (I915_READ(DP_D) & DP_DETECTED)) {
+ DRM_DEBUG_KMS("probing DP_D\n");
+ intel_dp_init(dev, DP_D);
+ }
+ } else if (IS_GEN2(dev))
+ intel_dvo_init(dev);
-static void ironlake_teardown_rc6(struct drm_device *dev)
-{
- struct drm_i915_private *dev_priv = dev->dev_private;
+ if (SUPPORTS_TV(dev))
+ intel_tv_init(dev);
- if (dev_priv->renderctx) {
- i915_gem_object_unpin(dev_priv->renderctx);
- drm_gem_object_unreference(&dev_priv->renderctx->base);
- dev_priv->renderctx = NULL;
+ list_for_each_entry(encoder, &dev->mode_config.encoder_list, base.head) {
+ encoder->base.possible_crtcs = encoder->crtc_mask;
+ encoder->base.possible_clones =
+ intel_encoder_clones(dev, encoder->clone_mask);
}
- if (dev_priv->pwrctx) {
- i915_gem_object_unpin(dev_priv->pwrctx);
- drm_gem_object_unreference(&dev_priv->pwrctx->base);
- dev_priv->pwrctx = NULL;
- }
+ /* disable all the possible outputs/crtcs before entering KMS mode */
+ drm_helper_disable_unused_functions(dev);
+
+ if (HAS_PCH_SPLIT(dev))
+ ironlake_init_pch_refclk(dev);
}
-static void ironlake_disable_rc6(struct drm_device *dev)
+static void intel_user_framebuffer_destroy(struct drm_framebuffer *fb)
{
- struct drm_i915_private *dev_priv = dev->dev_private;
-
- if (I915_READ(PWRCTXA)) {
- /* Wake the GPU, prevent RC6, then restore RSTDBYCTL */
- I915_WRITE(RSTDBYCTL, I915_READ(RSTDBYCTL) | RCX_SW_EXIT);
- wait_for(((I915_READ(RSTDBYCTL) & RSX_STATUS_MASK) == RSX_STATUS_ON),
- 50);
-
- I915_WRITE(PWRCTXA, 0);
- POSTING_READ(PWRCTXA);
+ struct intel_framebuffer *intel_fb = to_intel_framebuffer(fb);
- I915_WRITE(RSTDBYCTL, I915_READ(RSTDBYCTL) & ~RCX_SW_EXIT);
- POSTING_READ(RSTDBYCTL);
- }
+ drm_framebuffer_cleanup(fb);
+ drm_gem_object_unreference_unlocked(&intel_fb->obj->base);
- ironlake_teardown_rc6(dev);
+ kfree(intel_fb);
}
-static int ironlake_setup_rc6(struct drm_device *dev)
+static int intel_user_framebuffer_create_handle(struct drm_framebuffer *fb,
+ struct drm_file *file,
+ unsigned int *handle)
{
- struct drm_i915_private *dev_priv = dev->dev_private;
-
- if (dev_priv->renderctx == NULL)
- dev_priv->renderctx = intel_alloc_context_page(dev);
- if (!dev_priv->renderctx)
- return -ENOMEM;
-
- if (dev_priv->pwrctx == NULL)
- dev_priv->pwrctx = intel_alloc_context_page(dev);
- if (!dev_priv->pwrctx) {
- ironlake_teardown_rc6(dev);
- return -ENOMEM;
- }
+ struct intel_framebuffer *intel_fb = to_intel_framebuffer(fb);
+ struct drm_i915_gem_object *obj = intel_fb->obj;
- return 0;
+ return drm_gem_handle_create(file, &obj->base, handle);
}
-void ironlake_enable_rc6(struct drm_device *dev)
+static const struct drm_framebuffer_funcs intel_fb_funcs = {
+ .destroy = intel_user_framebuffer_destroy,
+ .create_handle = intel_user_framebuffer_create_handle,
+};
+
+int intel_framebuffer_init(struct drm_device *dev,
+ struct intel_framebuffer *intel_fb,
+ struct drm_mode_fb_cmd2 *mode_cmd,
+ struct drm_i915_gem_object *obj)
{
- struct drm_i915_private *dev_priv = dev->dev_private;
int ret;
- /* rc6 disabled by default due to repeated reports of hanging during
- * boot and resume.
- */
- if (!intel_enable_rc6(dev))
- return;
+ if (obj->tiling_mode == I915_TILING_Y)
+ return -EINVAL;
- mutex_lock(&dev->struct_mutex);
- ret = ironlake_setup_rc6(dev);
- if (ret) {
- mutex_unlock(&dev->struct_mutex);
- return;
- }
+ if (mode_cmd->pitches[0] & 63)
+ return -EINVAL;
- /*
- * GPU can automatically power down the render unit if given a page
- * to save state.
- */
- ret = BEGIN_LP_RING(6);
- if (ret) {
- ironlake_teardown_rc6(dev);
- mutex_unlock(&dev->struct_mutex);
- return;
+ switch (mode_cmd->pixel_format) {
+ case DRM_FORMAT_RGB332:
+ case DRM_FORMAT_RGB565:
+ case DRM_FORMAT_XRGB8888:
+ case DRM_FORMAT_XBGR8888:
+ case DRM_FORMAT_ARGB8888:
+ case DRM_FORMAT_XRGB2101010:
+ case DRM_FORMAT_ARGB2101010:
+ /* RGB formats are common across chipsets */
+ break;
+ case DRM_FORMAT_YUYV:
+ case DRM_FORMAT_UYVY:
+ case DRM_FORMAT_YVYU:
+ case DRM_FORMAT_VYUY:
+ break;
+ default:
+ DRM_DEBUG_KMS("unsupported pixel format %u\n",
+ mode_cmd->pixel_format);
+ return -EINVAL;
}
- OUT_RING(MI_SUSPEND_FLUSH | MI_SUSPEND_FLUSH_EN);
- OUT_RING(MI_SET_CONTEXT);
- OUT_RING(dev_priv->renderctx->gtt_offset |
- MI_MM_SPACE_GTT |
- MI_SAVE_EXT_STATE_EN |
- MI_RESTORE_EXT_STATE_EN |
- MI_RESTORE_INHIBIT);
- OUT_RING(MI_SUSPEND_FLUSH);
- OUT_RING(MI_NOOP);
- OUT_RING(MI_FLUSH);
- ADVANCE_LP_RING();
-
- /*
- * Wait for the command parser to advance past MI_SET_CONTEXT. The HW
- * does an implicit flush, combined with MI_FLUSH above, it should be
- * safe to assume that renderctx is valid
- */
- ret = intel_wait_ring_idle(LP_RING(dev_priv));
+ ret = drm_framebuffer_init(dev, &intel_fb->base, &intel_fb_funcs);
if (ret) {
- DRM_ERROR("failed to enable ironlake power power savings\n");
- ironlake_teardown_rc6(dev);
- mutex_unlock(&dev->struct_mutex);
- return;
+ DRM_ERROR("framebuffer init failed %d\n", ret);
+ return ret;
}
- I915_WRITE(PWRCTXA, dev_priv->pwrctx->gtt_offset | PWRCTX_EN);
- I915_WRITE(RSTDBYCTL, I915_READ(RSTDBYCTL) & ~RCX_SW_EXIT);
- mutex_unlock(&dev->struct_mutex);
+ drm_helper_mode_fill_fb_struct(&intel_fb->base, mode_cmd);
+ intel_fb->obj = obj;
+ return 0;
}
-void intel_init_clock_gating(struct drm_device *dev)
+static struct drm_framebuffer *
+intel_user_framebuffer_create(struct drm_device *dev,
+ struct drm_file *filp,
+ struct drm_mode_fb_cmd2 *mode_cmd)
{
- struct drm_i915_private *dev_priv = dev->dev_private;
+ struct drm_i915_gem_object *obj;
- dev_priv->display.init_clock_gating(dev);
+ obj = to_intel_bo(drm_gem_object_lookup(dev, filp,
+ mode_cmd->handles[0]));
+ if (&obj->base == NULL)
+ return ERR_PTR(-ENOENT);
- if (dev_priv->display.init_pch_clock_gating)
- dev_priv->display.init_pch_clock_gating(dev);
+ return intel_framebuffer_create(dev, mode_cmd, obj);
}
+static const struct drm_mode_config_funcs intel_mode_funcs = {
+ .fb_create = intel_user_framebuffer_create,
+ .output_poll_changed = intel_fb_output_poll_changed,
+};
+
/* Set up chip specific display functions */
static void intel_init_display(struct drm_device *dev)
{
projects / linux-imx.git / commitdiff