intel_attach_broadcast_rgb_property(connector);
}
+static void
+intel_dp_init_panel_power_sequencer(struct drm_device *dev,
+ struct intel_dp *intel_dp)
+{
+ struct drm_i915_private *dev_priv = dev->dev_private;
+ struct edp_power_seq cur, vbt, spec, final;
+ u32 pp_on, pp_off, pp_div, pp;
+
+ /* Workaround: Need to write PP_CONTROL with the unlock key as
+ * the very first thing. */
+ pp = ironlake_get_pp_control(dev_priv);
+ I915_WRITE(PCH_PP_CONTROL, pp);
+
+ pp_on = I915_READ(PCH_PP_ON_DELAYS);
+ pp_off = I915_READ(PCH_PP_OFF_DELAYS);
+ pp_div = I915_READ(PCH_PP_DIVISOR);
+
+ /* Pull timing values out of registers */
+ cur.t1_t3 = (pp_on & PANEL_POWER_UP_DELAY_MASK) >>
+ PANEL_POWER_UP_DELAY_SHIFT;
+
+ cur.t8 = (pp_on & PANEL_LIGHT_ON_DELAY_MASK) >>
+ PANEL_LIGHT_ON_DELAY_SHIFT;
+
+ cur.t9 = (pp_off & PANEL_LIGHT_OFF_DELAY_MASK) >>
+ PANEL_LIGHT_OFF_DELAY_SHIFT;
+
+ cur.t10 = (pp_off & PANEL_POWER_DOWN_DELAY_MASK) >>
+ PANEL_POWER_DOWN_DELAY_SHIFT;
+
+ cur.t11_t12 = ((pp_div & PANEL_POWER_CYCLE_DELAY_MASK) >>
+ PANEL_POWER_CYCLE_DELAY_SHIFT) * 1000;
+
+ DRM_DEBUG_KMS("cur t1_t3 %d t8 %d t9 %d t10 %d t11_t12 %d\n",
+ cur.t1_t3, cur.t8, cur.t9, cur.t10, cur.t11_t12);
+
+ vbt = dev_priv->edp.pps;
+
+ /* Upper limits from eDP 1.3 spec. Note that we use the clunky units of
+ * our hw here, which are all in 100usec. */
+ spec.t1_t3 = 210 * 10;
+ spec.t8 = 50 * 10; /* no limit for t8, use t7 instead */
+ spec.t9 = 50 * 10; /* no limit for t9, make it symmetric with t8 */
+ spec.t10 = 500 * 10;
+ /* This one is special and actually in units of 100ms, but zero
+ * based in the hw (so we need to add 100 ms). But the sw vbt
+ * table multiplies it with 1000 to make it in units of 100usec,
+ * too. */
+ spec.t11_t12 = (510 + 100) * 10;
+
+ DRM_DEBUG_KMS("vbt t1_t3 %d t8 %d t9 %d t10 %d t11_t12 %d\n",
+ vbt.t1_t3, vbt.t8, vbt.t9, vbt.t10, vbt.t11_t12);
+
+ /* Use the max of the register settings and vbt. If both are
+ * unset, fall back to the spec limits. */
+#define assign_final(field) final.field = (max(cur.field, vbt.field) == 0 ? \
+ spec.field : \
+ max(cur.field, vbt.field))
+ assign_final(t1_t3);
+ assign_final(t8);
+ assign_final(t9);
+ assign_final(t10);
+ assign_final(t11_t12);
+#undef assign_final
+
+#define get_delay(field) (DIV_ROUND_UP(final.field, 10))
+ intel_dp->panel_power_up_delay = get_delay(t1_t3);
+ intel_dp->backlight_on_delay = get_delay(t8);
+ intel_dp->backlight_off_delay = get_delay(t9);
+ intel_dp->panel_power_down_delay = get_delay(t10);
+ intel_dp->panel_power_cycle_delay = get_delay(t11_t12);
+#undef get_delay
+
+ /* And finally store the new values in the power sequencer. */
+ pp_on = (final.t1_t3 << PANEL_POWER_UP_DELAY_SHIFT) |
+ (final.t8 << PANEL_LIGHT_ON_DELAY_SHIFT);
+ pp_off = (final.t9 << PANEL_LIGHT_OFF_DELAY_SHIFT) |
+ (final.t10 << PANEL_POWER_DOWN_DELAY_SHIFT);
+ /* Compute the divisor for the pp clock, simply match the Bspec
+ * formula. */
+ pp_div = ((100 * intel_pch_rawclk(dev))/2 - 1)
+ << PP_REFERENCE_DIVIDER_SHIFT;
+ pp_div |= (DIV_ROUND_UP(final.t11_t12, 1000)
+ << PANEL_POWER_CYCLE_DELAY_SHIFT);
+
+ /* Haswell doesn't have any port selection bits for the panel
+ * power sequencer any more. */
+ if (HAS_PCH_IBX(dev) || HAS_PCH_CPT(dev)) {
+ if (is_cpu_edp(intel_dp))
+ pp_on |= PANEL_POWER_PORT_DP_A;
+ else
+ pp_on |= PANEL_POWER_PORT_DP_D;
+ }
+
+ I915_WRITE(PCH_PP_ON_DELAYS, pp_on);
+ I915_WRITE(PCH_PP_OFF_DELAYS, pp_off);
+ I915_WRITE(PCH_PP_DIVISOR, pp_div);
+
+
+ DRM_DEBUG_KMS("panel power up delay %d, power down delay %d, power cycle delay %d\n",
+ intel_dp->panel_power_up_delay, intel_dp->panel_power_down_delay,
+ intel_dp->panel_power_cycle_delay);
+
+ DRM_DEBUG_KMS("backlight on delay %d, off delay %d\n",
+ intel_dp->backlight_on_delay, intel_dp->backlight_off_delay);
+
+ DRM_DEBUG_KMS("panel power sequencer register settings: PP_ON %#x, PP_OFF %#x, PP_DIV %#x\n",
+ I915_READ(PCH_PP_ON_DELAYS),
+ I915_READ(PCH_PP_OFF_DELAYS),
+ I915_READ(PCH_PP_DIVISOR));
+}
+
void
intel_dp_init(struct drm_device *dev, int output_reg, enum port port)
{
break;
}
- /* Cache some DPCD data in the eDP case */
- if (is_edp(intel_dp)) {
- struct edp_power_seq cur, vbt, spec, final;
- u32 pp_on, pp_off, pp_div, pp;
-
- /* Workaround: Need to write PP_CONTROL with the unlock key as
- * the very first thing. */
- pp = ironlake_get_pp_control(dev_priv);
- I915_WRITE(PCH_PP_CONTROL, pp);
-
- pp_on = I915_READ(PCH_PP_ON_DELAYS);
- pp_off = I915_READ(PCH_PP_OFF_DELAYS);
- pp_div = I915_READ(PCH_PP_DIVISOR);
-
- /* Pull timing values out of registers */
- cur.t1_t3 = (pp_on & PANEL_POWER_UP_DELAY_MASK) >>
- PANEL_POWER_UP_DELAY_SHIFT;
-
- cur.t8 = (pp_on & PANEL_LIGHT_ON_DELAY_MASK) >>
- PANEL_LIGHT_ON_DELAY_SHIFT;
-
- cur.t9 = (pp_off & PANEL_LIGHT_OFF_DELAY_MASK) >>
- PANEL_LIGHT_OFF_DELAY_SHIFT;
-
- cur.t10 = (pp_off & PANEL_POWER_DOWN_DELAY_MASK) >>
- PANEL_POWER_DOWN_DELAY_SHIFT;
-
- cur.t11_t12 = ((pp_div & PANEL_POWER_CYCLE_DELAY_MASK) >>
- PANEL_POWER_CYCLE_DELAY_SHIFT) * 1000;
-
- DRM_DEBUG_KMS("cur t1_t3 %d t8 %d t9 %d t10 %d t11_t12 %d\n",
- cur.t1_t3, cur.t8, cur.t9, cur.t10, cur.t11_t12);
-
- vbt = dev_priv->edp.pps;
-
- /* Upper limits from eDP 1.3 spec. Note that we use the clunky
- * units of our hw here, which are all in 100usec. */
- spec.t1_t3 = 210 * 10;
- spec.t8 = 50 * 10; /* no limit for t8, use t7 instead */
- spec.t9 = 50 * 10; /* no limit for t9, make it symmetric with t8 */
- spec.t10 = 500 * 10;
- /* This one is special and actually in units of 100ms, but zero
- * based in the hw (so we need to add 100 ms). But the sw vbt
- * table multiplies it with 1000 to make it in units of 100usec,
- * too. */
- spec.t11_t12 = (510 + 100) * 10;
-
- DRM_DEBUG_KMS("vbt t1_t3 %d t8 %d t9 %d t10 %d t11_t12 %d\n",
- vbt.t1_t3, vbt.t8, vbt.t9, vbt.t10, vbt.t11_t12);
-
- /* Use the max of the register settings and vbt. If both are
- * unset, fall back to the spec limits. */
-#define assign_final(field) final.field = (max(cur.field, vbt.field) == 0 ? \
- spec.field : \
- max(cur.field, vbt.field))
- assign_final(t1_t3);
- assign_final(t8);
- assign_final(t9);
- assign_final(t10);
- assign_final(t11_t12);
-#undef assign_final
-
-#define get_delay(field) (DIV_ROUND_UP(final.field, 10))
- intel_dp->panel_power_up_delay = get_delay(t1_t3);
- intel_dp->backlight_on_delay = get_delay(t8);
- intel_dp->backlight_off_delay = get_delay(t9);
- intel_dp->panel_power_down_delay = get_delay(t10);
- intel_dp->panel_power_cycle_delay = get_delay(t11_t12);
-#undef get_delay
-
- /* And finally store the new values in the power sequencer. */
- pp_on = (final.t1_t3 << PANEL_POWER_UP_DELAY_SHIFT) |
- (final.t8 << PANEL_LIGHT_ON_DELAY_SHIFT);
- pp_off = (final.t9 << PANEL_LIGHT_OFF_DELAY_SHIFT) |
- (final.t10 << PANEL_POWER_DOWN_DELAY_SHIFT);
- /* Compute the divisor for the pp clock, simply match the Bspec
- * formula. */
- pp_div = ((100 * intel_pch_rawclk(dev))/2 - 1)
- << PP_REFERENCE_DIVIDER_SHIFT;
- pp_div |= (DIV_ROUND_UP(final.t11_t12, 1000)
- << PANEL_POWER_CYCLE_DELAY_SHIFT);
-
- /* Haswell doesn't have any port selection bits for the panel
- * power sequence any more. */
- if (HAS_PCH_IBX(dev) || HAS_PCH_CPT(dev)) {
- if (is_cpu_edp(intel_dp))
- pp_on |= PANEL_POWER_PORT_DP_A;
- else
- pp_on |= PANEL_POWER_PORT_DP_D;
- }
-
- I915_WRITE(PCH_PP_ON_DELAYS, pp_on);
- I915_WRITE(PCH_PP_OFF_DELAYS, pp_off);
- I915_WRITE(PCH_PP_DIVISOR, pp_div);
-
-
- DRM_DEBUG_KMS("panel power up delay %d, power down delay %d, power cycle delay %d\n",
- intel_dp->panel_power_up_delay, intel_dp->panel_power_down_delay,
- intel_dp->panel_power_cycle_delay);
-
- DRM_DEBUG_KMS("backlight on delay %d, off delay %d\n",
- intel_dp->backlight_on_delay, intel_dp->backlight_off_delay);
-
- DRM_DEBUG_KMS("panel power sequencer register settings: PP_ON %#x, PP_OFF %#x, PP_DIV %#x\n",
- I915_READ(PCH_PP_ON_DELAYS),
- I915_READ(PCH_PP_OFF_DELAYS),
- I915_READ(PCH_PP_DIVISOR));
- }
+ if (is_edp(intel_dp))
+ intel_dp_init_panel_power_sequencer(dev, intel_dp);
intel_dp_i2c_init(intel_dp, intel_connector, name);
+ /* Cache DPCD and EDID for edp. */
if (is_edp(intel_dp)) {
bool ret;
struct drm_display_mode *scan;
projects / linux-imx.git / commitdiff