/* 2 MHz master clock */
#define LABPC_TIMER_BASE 500
-/* Registers for the lab-pc+ */
-
-/* write-only registers */
-#define COMMAND1_REG 0x0
-#define ADC_GAIN_MASK (0x7 << 4)
-#define ADC_CHAN_BITS(x) ((x) & 0x7)
-/* enables multi channel scans */
-#define ADC_SCAN_EN_BIT 0x80
-#define COMMAND2_REG 0x1
-/* enable pretriggering (used in conjunction with SWTRIG) */
-#define PRETRIG_BIT 0x1
-/* enable paced conversions on external trigger */
-#define HWTRIG_BIT 0x2
-/* enable paced conversions */
-#define SWTRIG_BIT 0x4
-/* use two cascaded counters for pacing */
-#define CASCADE_BIT 0x8
-#define DAC_PACED_BIT(channel) (0x40 << ((channel) & 0x1))
-#define COMMAND3_REG 0x2
-/* enable dma transfers */
-#define DMA_EN_BIT 0x1
-/* enable interrupts for 8255 */
-#define DIO_INTR_EN_BIT 0x2
-/* enable dma terminal count interrupt */
-#define DMATC_INTR_EN_BIT 0x4
-/* enable timer interrupt */
-#define TIMER_INTR_EN_BIT 0x8
-/* enable error interrupt */
-#define ERR_INTR_EN_BIT 0x10
-/* enable fifo not empty interrupt */
-#define ADC_FNE_INTR_EN_BIT 0x20
-#define ADC_CONVERT_REG 0x3
-#define DAC_LSB_REG(channel) (0x4 + 2 * ((channel) & 0x1))
-#define DAC_MSB_REG(channel) (0x5 + 2 * ((channel) & 0x1))
-#define ADC_CLEAR_REG 0x8
-#define DMATC_CLEAR_REG 0xa
-#define TIMER_CLEAR_REG 0xc
-/* 1200 boards only */
-#define COMMAND6_REG 0xe
-/* select ground or common-mode reference */
-#define ADC_COMMON_BIT 0x1
-/* adc unipolar */
-#define ADC_UNIP_BIT 0x2
-/* dac unipolar */
-#define DAC_UNIP_BIT(channel) (0x4 << ((channel) & 0x1))
-/* enable fifo half full interrupt */
-#define ADC_FHF_INTR_EN_BIT 0x20
-/* enable interrupt on end of hardware count */
-#define A1_INTR_EN_BIT 0x40
-/* scan up from channel zero instead of down to zero */
-#define ADC_SCAN_UP_BIT 0x80
-#define COMMAND4_REG 0xf
-/* enables 'interval' scanning */
-#define INTERVAL_SCAN_EN_BIT 0x1
-/* enables external signal on counter b1 output to trigger scan */
-#define EXT_SCAN_EN_BIT 0x2
-/* chooses direction (output or input) for EXTCONV* line */
-#define EXT_CONVERT_OUT_BIT 0x4
-/* chooses differential inputs for adc (in conjunction with board jumper) */
-#define ADC_DIFF_BIT 0x8
-#define EXT_CONVERT_DISABLE_BIT 0x10
-/* 1200 boards only, calibration stuff */
-#define COMMAND5_REG 0x1c
-/* enable eeprom for write */
-#define EEPROM_WRITE_UNPROTECT_BIT 0x4
-/* enable dithering */
-#define DITHER_EN_BIT 0x8
-/* load calibration dac */
-#define CALDAC_LOAD_BIT 0x10
-/* serial clock - rising edge writes, falling edge reads */
-#define SCLOCK_BIT 0x20
-/* serial data bit for writing to eeprom or calibration dacs */
-#define SDATA_BIT 0x40
-/* enable eeprom for read/write */
-#define EEPROM_EN_BIT 0x80
-#define INTERVAL_COUNT_REG 0x1e
-#define INTERVAL_LOAD_REG 0x1f
-#define INTERVAL_LOAD_BITS 0x1
-
-/* read-only registers */
-#define STATUS1_REG 0x0
-/* data is available in fifo */
-#define DATA_AVAIL_BIT 0x1
-/* overrun has occurred */
-#define OVERRUN_BIT 0x2
-/* fifo overflow */
-#define OVERFLOW_BIT 0x4
-/* timer interrupt has occurred */
-#define TIMER_BIT 0x8
-/* dma terminal count has occurred */
-#define DMATC_BIT 0x10
-/* external trigger has occurred */
-#define EXT_TRIG_BIT 0x40
-/* 1200 boards only */
-#define STATUS2_REG 0x1d
-/* programmable eeprom serial output */
-#define EEPROM_OUT_BIT 0x1
-/* counter A1 terminal count */
-#define A1_TC_BIT 0x2
-/* fifo not half full */
-#define FNHF_BIT 0x4
-#define ADC_FIFO_REG 0xa
-
-#define DIO_BASE_REG 0x10
-#define COUNTER_A_BASE_REG 0x14
-#define COUNTER_A_CONTROL_REG (COUNTER_A_BASE_REG + 0x3)
-/* check modes put conversion pacer output in harmless state (a0 mode 2) */
-#define INIT_A0_BITS 0x14
-/* put hardware conversion counter output in harmless state (a1 mode 0) */
-#define INIT_A1_BITS 0x70
-#define COUNTER_B_BASE_REG 0x18
+/*
+ * Register map (all registers are 8-bit)
+ */
+#define STAT1_REG 0x00 /* R: Status 1 reg */
+#define STAT1_DAVAIL (1 << 0)
+#define STAT1_OVERRUN (1 << 1)
+#define STAT1_OVERFLOW (1 << 2)
+#define STAT1_CNTINT (1 << 3)
+#define STAT1_GATA0 (1 << 5)
+#define STAT1_EXTGATA0 (1 << 6)
+#define CMD1_REG 0x00 /* W: Command 1 reg */
+#define CMD1_MA(x) (((x) & 0x7) << 0)
+#define CMD1_TWOSCMP (1 << 3)
+#define CMD1_GAIN_MASK (7 << 4)
+#define CMD1_SCANEN (1 << 7)
+#define CMD2_REG 0x01 /* W: Command 2 reg */
+#define CMD2_PRETRIG (1 << 0)
+#define CMD2_HWTRIG (1 << 1)
+#define CMD2_SWTRIG (1 << 2)
+#define CMD2_TBSEL (1 << 3)
+#define CMD2_2SDAC0 (1 << 4)
+#define CMD2_2SDAC1 (1 << 5)
+#define CMD2_LDAC(x) (1 << (6 + (x)))
+#define CMD3_REG 0x02 /* W: Command 3 reg */
+#define CMD3_DMAEN (1 << 0)
+#define CMD3_DIOINTEN (1 << 1)
+#define CMD3_DMATCINTEN (1 << 2)
+#define CMD3_CNTINTEN (1 << 3)
+#define CMD3_ERRINTEN (1 << 4)
+#define CMD3_FIFOINTEN (1 << 5)
+#define ADC_START_CONVERT_REG 0x03 /* W: Start Convert reg */
+#define DAC_LSB_REG(x) (0x04 + 2 * (x)) /* W: DAC0/1 LSB reg */
+#define DAC_MSB_REG(x) (0x05 + 2 * (x)) /* W: DAC0/1 MSB reg */
+#define ADC_FIFO_CLEAR_REG 0x08 /* W: A/D FIFO Clear reg */
+#define ADC_FIFO_REG 0x0a /* R: A/D FIFO reg */
+#define DMATC_CLEAR_REG 0x0a /* W: DMA Interrupt Clear reg */
+#define TIMER_CLEAR_REG 0x0c /* W: Timer Interrupt Clear reg */
+#define CMD6_REG 0x0e /* W: Command 6 reg */
+#define CMD6_NRSE (1 << 0)
+#define CMD6_ADCUNI (1 << 1)
+#define CMD6_DACUNI(x) (1 << (2 + (x)))
+#define CMD6_HFINTEN (1 << 5)
+#define CMD6_DQINTEN (1 << 6)
+#define CMD6_SCANUP (1 << 7)
+#define CMD4_REG 0x0f /* W: Command 3 reg */
+#define CMD4_INTSCAN (1 << 0)
+#define CMD4_EOIRCV (1 << 1)
+#define CMD4_ECLKDRV (1 << 2)
+#define CMD4_SEDIFF (1 << 3)
+#define CMD4_ECLKRCV (1 << 4)
+#define DIO_BASE_REG 0x10 /* R/W: 8255 DIO base reg */
+#define COUNTER_A_BASE_REG 0x14 /* R/W: 8253 Counter A base reg */
+#define COUNTER_A_MODE_REG 0x17 /* W: 8253 Counter A mode reg */
+#define INIT_A0_BITS 0x14 /* (a0 mode 2) */
+#define INIT_A1_BITS 0x70 /* (a1 mode 0) */
+#define COUNTER_B_BASE_REG 0x18 /* R/W: 8253 Counter B base reg */
+#define CMD5_REG 0x1c /* W: Command 5 reg */
+#define CMD5_WRTPRT (1 << 2)
+#define CMD5_DITHEREN (1 << 3)
+#define CMD5_CALDACLD (1 << 4)
+#define CMD5_SCLK (1 << 5)
+#define CMD5_SDATA (1 << 6)
+#define CMD5_EEPROMCS (1 << 7)
+#define STAT2_REG 0x1d /* R: Status 2 reg */
+#define STAT2_PROMOUT (1 << 0)
+#define STAT2_OUTA1 (1 << 1)
+#define STAT2_FIFONHF (1 << 2)
+#define INTERVAL_COUNT_REG 0x1e /* W: Interval Counter Data reg */
+#define INTERVAL_STROBE_REG 0x1f /* W: Interval Counter Strobe reg */
#define LABPC_ADC_TIMEOUT 1000
unsigned long flags;
spin_lock_irqsave(&dev->spinlock, flags);
- devpriv->cmd2 &= ~SWTRIG_BIT & ~HWTRIG_BIT & ~PRETRIG_BIT;
- devpriv->write_byte(devpriv->cmd2, dev->iobase + COMMAND2_REG);
+ devpriv->cmd2 &= ~(CMD2_SWTRIG | CMD2_HWTRIG | CMD2_PRETRIG);
+ devpriv->write_byte(devpriv->cmd2, dev->iobase + CMD2_REG);
spin_unlock_irqrestore(&dev->spinlock, flags);
devpriv->cmd3 = 0;
- devpriv->write_byte(devpriv->cmd3, dev->iobase + COMMAND3_REG);
+ devpriv->write_byte(devpriv->cmd3, dev->iobase + CMD3_REG);
return 0;
}
if ((mode == MODE_SINGLE_CHAN || mode == MODE_SINGLE_CHAN_INTERVAL) &&
aref == AREF_DIFF)
chan *= 2;
- devpriv->cmd1 = ADC_CHAN_BITS(chan);
+ devpriv->cmd1 = CMD1_MA(chan);
devpriv->cmd1 |= board->ai_range_code[range];
- devpriv->write_byte(devpriv->cmd1, dev->iobase + COMMAND1_REG);
+ devpriv->write_byte(devpriv->cmd1, dev->iobase + CMD1_REG);
}
static void labpc_setup_cmd6_reg(struct comedi_device *dev,
/* reference inputs to ground or common? */
if (aref != AREF_GROUND)
- devpriv->cmd6 |= ADC_COMMON_BIT;
+ devpriv->cmd6 |= CMD6_NRSE;
else
- devpriv->cmd6 &= ~ADC_COMMON_BIT;
+ devpriv->cmd6 &= ~CMD6_NRSE;
/* bipolar or unipolar range? */
if (labpc_range_is_unipolar(s, range))
- devpriv->cmd6 |= ADC_UNIP_BIT;
+ devpriv->cmd6 |= CMD6_ADCUNI;
else
- devpriv->cmd6 &= ~ADC_UNIP_BIT;
+ devpriv->cmd6 &= ~CMD6_ADCUNI;
/* interrupt on fifo half full? */
if (xfer == fifo_half_full_transfer)
- devpriv->cmd6 |= ADC_FHF_INTR_EN_BIT;
+ devpriv->cmd6 |= CMD6_HFINTEN;
else
- devpriv->cmd6 &= ~ADC_FHF_INTR_EN_BIT;
+ devpriv->cmd6 &= ~CMD6_HFINTEN;
/* enable interrupt on counter a1 terminal count? */
if (ena_intr)
- devpriv->cmd6 |= A1_INTR_EN_BIT;
+ devpriv->cmd6 |= CMD6_DQINTEN;
else
- devpriv->cmd6 &= ~A1_INTR_EN_BIT;
+ devpriv->cmd6 &= ~CMD6_DQINTEN;
/* are we scanning up or down through channels? */
if (mode == MODE_MULT_CHAN_UP)
- devpriv->cmd6 |= ADC_SCAN_UP_BIT;
+ devpriv->cmd6 |= CMD6_SCANUP;
else
- devpriv->cmd6 &= ~ADC_SCAN_UP_BIT;
+ devpriv->cmd6 &= ~CMD6_SCANUP;
- devpriv->write_byte(devpriv->cmd6, dev->iobase + COMMAND6_REG);
+ devpriv->write_byte(devpriv->cmd6, dev->iobase + CMD6_REG);
}
static unsigned int labpc_read_adc_fifo(struct comedi_device *dev)
{
struct labpc_private *devpriv = dev->private;
- devpriv->write_byte(0x1, dev->iobase + ADC_CLEAR_REG);
+ devpriv->write_byte(0x1, dev->iobase + ADC_FIFO_CLEAR_REG);
labpc_read_adc_fifo(dev);
}
int i;
for (i = 0; i < timeout; i++) {
- devpriv->stat1 = devpriv->read_byte(dev->iobase + STATUS1_REG);
- if (devpriv->stat1 & DATA_AVAIL_BIT)
+ devpriv->stat1 = devpriv->read_byte(dev->iobase + STAT1_REG);
+ if (devpriv->stat1 & STAT1_DAVAIL)
return 0;
udelay(1);
}
/* setup cmd4 register */
devpriv->cmd4 = 0;
- devpriv->cmd4 |= EXT_CONVERT_DISABLE_BIT;
+ devpriv->cmd4 |= CMD4_ECLKRCV;
/* single-ended/differential */
if (aref == AREF_DIFF)
- devpriv->cmd4 |= ADC_DIFF_BIT;
- devpriv->write_byte(devpriv->cmd4, dev->iobase + COMMAND4_REG);
+ devpriv->cmd4 |= CMD4_SEDIFF;
+ devpriv->write_byte(devpriv->cmd4, dev->iobase + CMD4_REG);
/*
* initialize pacer counter output to make sure it doesn't
* cause any problems
*/
- devpriv->write_byte(INIT_A0_BITS, dev->iobase + COUNTER_A_CONTROL_REG);
+ devpriv->write_byte(INIT_A0_BITS, dev->iobase + COUNTER_A_MODE_REG);
labpc_clear_adc_fifo(dev);
for (i = 0; i < insn->n; i++) {
/* trigger conversion */
- devpriv->write_byte(0x1, dev->iobase + ADC_CONVERT_REG);
+ devpriv->write_byte(0x1, dev->iobase + ADC_START_CONVERT_REG);
ret = labpc_ai_wait_for_data(dev, LABPC_ADC_TIMEOUT);
if (ret)
* with no count to set its output low
*/
devpriv->write_byte(INIT_A1_BITS,
- dev->iobase + COUNTER_A_CONTROL_REG);
+ dev->iobase + COUNTER_A_MODE_REG);
#ifdef CONFIG_ISA_DMA_API
/* figure out what method we will use to transfer data */
/* manual says to set scan enable bit on second pass */
if (mode == MODE_MULT_CHAN_UP || mode == MODE_MULT_CHAN_DOWN) {
- devpriv->cmd1 |= ADC_SCAN_EN_BIT;
+ devpriv->cmd1 |= CMD1_SCANEN;
/* need a brief delay before enabling scan, or scan
* list will get screwed when you switch
* between scan up to scan down mode - dunno why */
udelay(1);
- devpriv->write_byte(devpriv->cmd1, dev->iobase + COMMAND1_REG);
+ devpriv->write_byte(devpriv->cmd1, dev->iobase + CMD1_REG);
}
devpriv->write_byte(cmd->chanlist_len,
dev->iobase + INTERVAL_COUNT_REG);
/* load count */
- devpriv->write_byte(INTERVAL_LOAD_BITS,
- dev->iobase + INTERVAL_LOAD_REG);
+ devpriv->write_byte(0x1, dev->iobase + INTERVAL_STROBE_REG);
if (cmd->convert_src == TRIG_TIMER ||
cmd->scan_begin_src == TRIG_TIMER) {
}
} else
devpriv->write_byte(INIT_A0_BITS,
- dev->iobase + COUNTER_A_CONTROL_REG);
+ dev->iobase + COUNTER_A_MODE_REG);
/* set up scan pacing */
if (labpc_ai_scan_period(cmd, mode)) {
enable_dma(devpriv->dma_chan);
release_dma_lock(irq_flags);
/* enable board's dma */
- devpriv->cmd3 |= DMA_EN_BIT | DMATC_INTR_EN_BIT;
+ devpriv->cmd3 |= (CMD3_DMAEN | CMD3_DMATCINTEN);
} else
- devpriv->cmd3 &= ~DMA_EN_BIT & ~DMATC_INTR_EN_BIT;
+ devpriv->cmd3 &= ~(CMD3_DMAEN | CMD3_DMATCINTEN);
#endif
/* enable error interrupts */
- devpriv->cmd3 |= ERR_INTR_EN_BIT;
+ devpriv->cmd3 |= CMD3_ERRINTEN;
/* enable fifo not empty interrupt? */
if (xfer == fifo_not_empty_transfer)
- devpriv->cmd3 |= ADC_FNE_INTR_EN_BIT;
+ devpriv->cmd3 |= CMD3_FIFOINTEN;
else
- devpriv->cmd3 &= ~ADC_FNE_INTR_EN_BIT;
- devpriv->write_byte(devpriv->cmd3, dev->iobase + COMMAND3_REG);
+ devpriv->cmd3 &= ~CMD3_FIFOINTEN;
+ devpriv->write_byte(devpriv->cmd3, dev->iobase + CMD3_REG);
/* setup any external triggering/pacing (cmd4 register) */
devpriv->cmd4 = 0;
if (cmd->convert_src != TRIG_EXT)
- devpriv->cmd4 |= EXT_CONVERT_DISABLE_BIT;
+ devpriv->cmd4 |= CMD4_ECLKRCV;
/* XXX should discard first scan when using interval scanning
* since manual says it is not synced with scan clock */
if (labpc_use_continuous_mode(cmd, mode) == 0) {
- devpriv->cmd4 |= INTERVAL_SCAN_EN_BIT;
+ devpriv->cmd4 |= CMD4_INTSCAN;
if (cmd->scan_begin_src == TRIG_EXT)
- devpriv->cmd4 |= EXT_SCAN_EN_BIT;
+ devpriv->cmd4 |= CMD4_EOIRCV;
}
/* single-ended/differential */
if (aref == AREF_DIFF)
- devpriv->cmd4 |= ADC_DIFF_BIT;
- devpriv->write_byte(devpriv->cmd4, dev->iobase + COMMAND4_REG);
+ devpriv->cmd4 |= CMD4_SEDIFF;
+ devpriv->write_byte(devpriv->cmd4, dev->iobase + CMD4_REG);
/* startup acquisition */
/* cmd2 reg */
/* use 2 cascaded counters for pacing */
spin_lock_irqsave(&dev->spinlock, flags);
- devpriv->cmd2 |= CASCADE_BIT;
+ devpriv->cmd2 |= CMD2_TBSEL;
switch (cmd->start_src) {
case TRIG_EXT:
- devpriv->cmd2 |= HWTRIG_BIT;
- devpriv->cmd2 &= ~PRETRIG_BIT & ~SWTRIG_BIT;
+ devpriv->cmd2 |= CMD2_HWTRIG;
+ devpriv->cmd2 &= ~(CMD2_PRETRIG | CMD2_SWTRIG);
break;
case TRIG_NOW:
- devpriv->cmd2 |= SWTRIG_BIT;
- devpriv->cmd2 &= ~PRETRIG_BIT & ~HWTRIG_BIT;
+ devpriv->cmd2 |= CMD2_SWTRIG;
+ devpriv->cmd2 &= ~(CMD2_PRETRIG | CMD2_HWTRIG);
break;
default:
comedi_error(dev, "bug with start_src");
}
switch (cmd->stop_src) {
case TRIG_EXT:
- devpriv->cmd2 |= HWTRIG_BIT | PRETRIG_BIT;
+ devpriv->cmd2 |= (CMD2_HWTRIG | CMD2_PRETRIG);
break;
case TRIG_COUNT:
case TRIG_NONE:
spin_unlock_irqrestore(&dev->spinlock, flags);
return -1;
}
- devpriv->write_byte(devpriv->cmd2, dev->iobase + COMMAND2_REG);
+ devpriv->write_byte(devpriv->cmd2, dev->iobase + CMD2_REG);
spin_unlock_irqrestore(&dev->spinlock, flags);
return 0;
const int timeout = 10000;
unsigned int i;
- devpriv->stat1 = devpriv->read_byte(dev->iobase + STATUS1_REG);
+ devpriv->stat1 = devpriv->read_byte(dev->iobase + STAT1_REG);
- for (i = 0; (devpriv->stat1 & DATA_AVAIL_BIT) && i < timeout;
+ for (i = 0; (devpriv->stat1 & STAT1_DAVAIL) && i < timeout;
i++) {
/* quit if we have all the data we want */
if (async->cmd.stop_src == TRIG_COUNT) {
}
data = labpc_read_adc_fifo(dev);
cfc_write_to_buffer(dev->read_subdev, data);
- devpriv->stat1 = devpriv->read_byte(dev->iobase + STATUS1_REG);
+ devpriv->stat1 = devpriv->read_byte(dev->iobase + STAT1_REG);
}
if (i == timeout) {
comedi_error(dev, "ai timeout, fifo never empties");
async->events = 0;
/* read board status */
- devpriv->stat1 = devpriv->read_byte(dev->iobase + STATUS1_REG);
+ devpriv->stat1 = devpriv->read_byte(dev->iobase + STAT1_REG);
if (board->register_layout == labpc_1200_layout)
- devpriv->stat2 = devpriv->read_byte(dev->iobase + STATUS2_REG);
+ devpriv->stat2 = devpriv->read_byte(dev->iobase + STAT2_REG);
- if ((devpriv->stat1 & (DMATC_BIT | TIMER_BIT | OVERFLOW_BIT |
- OVERRUN_BIT | DATA_AVAIL_BIT)) == 0
- && (devpriv->stat2 & A1_TC_BIT) == 0
- && (devpriv->stat2 & FNHF_BIT)) {
+ if ((devpriv->stat1 & (STAT1_GATA0 | STAT1_CNTINT | STAT1_OVERFLOW |
+ STAT1_OVERRUN | STAT1_DAVAIL)) == 0
+ && (devpriv->stat2 & STAT2_OUTA1) == 0
+ && (devpriv->stat2 & STAT2_FIFONHF)) {
return IRQ_NONE;
}
- if (devpriv->stat1 & OVERRUN_BIT) {
+ if (devpriv->stat1 & STAT1_OVERRUN) {
/* clear error interrupt */
- devpriv->write_byte(0x1, dev->iobase + ADC_CLEAR_REG);
+ devpriv->write_byte(0x1, dev->iobase + ADC_FIFO_CLEAR_REG);
async->events |= COMEDI_CB_ERROR | COMEDI_CB_EOA;
comedi_event(dev, s);
comedi_error(dev, "overrun");
* if a dma terminal count of external stop trigger
* has occurred
*/
- if (devpriv->stat1 & DMATC_BIT ||
+ if (devpriv->stat1 & STAT1_GATA0 ||
(board->register_layout == labpc_1200_layout
- && devpriv->stat2 & A1_TC_BIT)) {
+ && devpriv->stat2 & STAT2_OUTA1)) {
handle_isa_dma(dev);
}
} else
#endif
labpc_drain_fifo(dev);
- if (devpriv->stat1 & TIMER_BIT) {
+ if (devpriv->stat1 & STAT1_CNTINT) {
comedi_error(dev, "handled timer interrupt?");
/* clear it */
devpriv->write_byte(0x1, dev->iobase + TIMER_CLEAR_REG);
}
- if (devpriv->stat1 & OVERFLOW_BIT) {
+ if (devpriv->stat1 & STAT1_OVERFLOW) {
/* clear error interrupt */
- devpriv->write_byte(0x1, dev->iobase + ADC_CLEAR_REG);
+ devpriv->write_byte(0x1, dev->iobase + ADC_FIFO_CLEAR_REG);
async->events |= COMEDI_CB_ERROR | COMEDI_CB_EOA;
comedi_event(dev, s);
comedi_error(dev, "overflow");
}
/* handle external stop trigger */
if (cmd->stop_src == TRIG_EXT) {
- if (devpriv->stat2 & A1_TC_BIT) {
+ if (devpriv->stat2 & STAT2_OUTA1) {
labpc_drain_dregs(dev);
labpc_cancel(dev, s);
async->events |= COMEDI_CB_EOA;
/* note: hardware bug in daqcard-1200 means pacing cannot
* be independently enabled/disabled for its the two channels */
spin_lock_irqsave(&dev->spinlock, flags);
- devpriv->cmd2 &= ~DAC_PACED_BIT(channel);
- devpriv->write_byte(devpriv->cmd2, dev->iobase + COMMAND2_REG);
+ devpriv->cmd2 &= ~CMD2_LDAC(channel);
+ devpriv->write_byte(devpriv->cmd2, dev->iobase + CMD2_REG);
spin_unlock_irqrestore(&dev->spinlock, flags);
/* set range */
if (board->register_layout == labpc_1200_layout) {
range = CR_RANGE(insn->chanspec);
if (labpc_range_is_unipolar(s, range))
- devpriv->cmd6 |= DAC_UNIP_BIT(channel);
+ devpriv->cmd6 |= CMD6_DACUNI(channel);
else
- devpriv->cmd6 &= ~DAC_UNIP_BIT(channel);
+ devpriv->cmd6 &= ~CMD6_DACUNI(channel);
/* write to register */
- devpriv->write_byte(devpriv->cmd6, dev->iobase + COMMAND6_REG);
+ devpriv->write_byte(devpriv->cmd6, dev->iobase + CMD6_REG);
}
/* send data */
lsb = data[0] & 0xff;
for (i = 1; i <= value_width; i++) {
/* clear serial clock */
- devpriv->cmd5 &= ~SCLOCK_BIT;
+ devpriv->cmd5 &= ~CMD5_SCLK;
/* send bits most significant bit first */
if (value & (1 << (value_width - i)))
- devpriv->cmd5 |= SDATA_BIT;
+ devpriv->cmd5 |= CMD5_SDATA;
else
- devpriv->cmd5 &= ~SDATA_BIT;
+ devpriv->cmd5 &= ~CMD5_SDATA;
udelay(1);
- devpriv->write_byte(devpriv->cmd5, dev->iobase + COMMAND5_REG);
+ devpriv->write_byte(devpriv->cmd5, dev->iobase + CMD5_REG);
/* set clock to load bit */
- devpriv->cmd5 |= SCLOCK_BIT;
+ devpriv->cmd5 |= CMD5_SCLK;
udelay(1);
- devpriv->write_byte(devpriv->cmd5,
- dev->iobase + COMMAND5_REG);
+ devpriv->write_byte(devpriv->cmd5, dev->iobase + CMD5_REG);
}
}
for (i = 1; i <= value_width; i++) {
/* set serial clock */
- devpriv->cmd5 |= SCLOCK_BIT;
+ devpriv->cmd5 |= CMD5_SCLK;
udelay(1);
- devpriv->write_byte(devpriv->cmd5, dev->iobase + COMMAND5_REG);
+ devpriv->write_byte(devpriv->cmd5, dev->iobase + CMD5_REG);
/* clear clock bit */
- devpriv->cmd5 &= ~SCLOCK_BIT;
+ devpriv->cmd5 &= ~CMD5_SCLK;
udelay(1);
- devpriv->write_byte(devpriv->cmd5, dev->iobase + COMMAND5_REG);
+ devpriv->write_byte(devpriv->cmd5, dev->iobase + CMD5_REG);
/* read bits most significant bit first */
udelay(1);
- devpriv->stat2 = devpriv->read_byte(dev->iobase + STATUS2_REG);
- if (devpriv->stat2 & EEPROM_OUT_BIT)
+ devpriv->stat2 = devpriv->read_byte(dev->iobase + STAT2_REG);
+ if (devpriv->stat2 & STAT2_PROMOUT)
value |= 1 << (value_width - i);
}
const int write_length = 8;
/* enable read/write to eeprom */
- devpriv->cmd5 &= ~EEPROM_EN_BIT;
+ devpriv->cmd5 &= ~CMD5_EEPROMCS;
udelay(1);
- devpriv->write_byte(devpriv->cmd5, dev->iobase + COMMAND5_REG);
- devpriv->cmd5 |= EEPROM_EN_BIT | EEPROM_WRITE_UNPROTECT_BIT;
+ devpriv->write_byte(devpriv->cmd5, dev->iobase + CMD5_REG);
+ devpriv->cmd5 |= (CMD5_EEPROMCS | CMD5_WRTPRT);
udelay(1);
- devpriv->write_byte(devpriv->cmd5, dev->iobase + COMMAND5_REG);
+ devpriv->write_byte(devpriv->cmd5, dev->iobase + CMD5_REG);
/* send read instruction */
labpc_serial_out(dev, read_instruction, write_length);
value = labpc_serial_in(dev);
/* disable read/write to eeprom */
- devpriv->cmd5 &= ~EEPROM_EN_BIT & ~EEPROM_WRITE_UNPROTECT_BIT;
+ devpriv->cmd5 &= ~(CMD5_EEPROMCS | CMD5_WRTPRT);
udelay(1);
- devpriv->write_byte(devpriv->cmd5, dev->iobase + COMMAND5_REG);
+ devpriv->write_byte(devpriv->cmd5, dev->iobase + CMD5_REG);
return value;
}
const int write_length = 8; /* 8 bit write lengths to eeprom */
/* enable read/write to eeprom */
- devpriv->cmd5 &= ~EEPROM_EN_BIT;
+ devpriv->cmd5 &= ~CMD5_EEPROMCS;
udelay(1);
- devpriv->write_byte(devpriv->cmd5, dev->iobase + COMMAND5_REG);
- devpriv->cmd5 |= EEPROM_EN_BIT | EEPROM_WRITE_UNPROTECT_BIT;
+ devpriv->write_byte(devpriv->cmd5, dev->iobase + CMD5_REG);
+ devpriv->cmd5 |= (CMD5_EEPROMCS | CMD5_WRTPRT);
udelay(1);
- devpriv->write_byte(devpriv->cmd5, dev->iobase + COMMAND5_REG);
+ devpriv->write_byte(devpriv->cmd5, dev->iobase + CMD5_REG);
/* send read status instruction */
labpc_serial_out(dev, read_status_instruction, write_length);
value = labpc_serial_in(dev);
/* disable read/write to eeprom */
- devpriv->cmd5 &= ~EEPROM_EN_BIT & ~EEPROM_WRITE_UNPROTECT_BIT;
+ devpriv->cmd5 &= ~(CMD5_EEPROMCS | CMD5_WRTPRT);
udelay(1);
- devpriv->write_byte(devpriv->cmd5, dev->iobase + COMMAND5_REG);
+ devpriv->write_byte(devpriv->cmd5, dev->iobase + CMD5_REG);
return value;
}
devpriv->eeprom_data[address] = value;
/* enable read/write to eeprom */
- devpriv->cmd5 &= ~EEPROM_EN_BIT;
+ devpriv->cmd5 &= ~CMD5_EEPROMCS;
udelay(1);
- devpriv->write_byte(devpriv->cmd5, dev->iobase + COMMAND5_REG);
- devpriv->cmd5 |= EEPROM_EN_BIT | EEPROM_WRITE_UNPROTECT_BIT;
+ devpriv->write_byte(devpriv->cmd5, dev->iobase + CMD5_REG);
+ devpriv->cmd5 |= (CMD5_EEPROMCS | CMD5_WRTPRT);
udelay(1);
- devpriv->write_byte(devpriv->cmd5, dev->iobase + COMMAND5_REG);
+ devpriv->write_byte(devpriv->cmd5, dev->iobase + CMD5_REG);
/* send write_enable instruction */
labpc_serial_out(dev, write_enable_instruction, write_length);
- devpriv->cmd5 &= ~EEPROM_EN_BIT;
+ devpriv->cmd5 &= ~CMD5_EEPROMCS;
udelay(1);
- devpriv->write_byte(devpriv->cmd5, dev->iobase + COMMAND5_REG);
+ devpriv->write_byte(devpriv->cmd5, dev->iobase + CMD5_REG);
/* send write instruction */
- devpriv->cmd5 |= EEPROM_EN_BIT;
+ devpriv->cmd5 |= CMD5_EEPROMCS;
udelay(1);
- devpriv->write_byte(devpriv->cmd5, dev->iobase + COMMAND5_REG);
+ devpriv->write_byte(devpriv->cmd5, dev->iobase + CMD5_REG);
labpc_serial_out(dev, write_instruction, write_length);
/* send 8 bit address to write to */
labpc_serial_out(dev, address, write_length);
/* write value */
labpc_serial_out(dev, value, write_length);
- devpriv->cmd5 &= ~EEPROM_EN_BIT;
+ devpriv->cmd5 &= ~CMD5_EEPROMCS;
udelay(1);
- devpriv->write_byte(devpriv->cmd5, dev->iobase + COMMAND5_REG);
+ devpriv->write_byte(devpriv->cmd5, dev->iobase + CMD5_REG);
/* disable read/write to eeprom */
- devpriv->cmd5 &= ~EEPROM_EN_BIT & ~EEPROM_WRITE_UNPROTECT_BIT;
+ devpriv->cmd5 &= ~(CMD5_EEPROMCS | CMD5_WRTPRT);
udelay(1);
- devpriv->write_byte(devpriv->cmd5, dev->iobase + COMMAND5_REG);
+ devpriv->write_byte(devpriv->cmd5, dev->iobase + CMD5_REG);
return 0;
}
devpriv->caldac[channel] = value;
/* clear caldac load bit and make sure we don't write to eeprom */
- devpriv->cmd5 &=
- ~CALDAC_LOAD_BIT & ~EEPROM_EN_BIT & ~EEPROM_WRITE_UNPROTECT_BIT;
+ devpriv->cmd5 &= ~(CMD5_CALDACLD | CMD5_EEPROMCS | CMD5_WRTPRT);
udelay(1);
- devpriv->write_byte(devpriv->cmd5, dev->iobase + COMMAND5_REG);
+ devpriv->write_byte(devpriv->cmd5, dev->iobase + CMD5_REG);
/* write 4 bit channel */
labpc_serial_out(dev, channel, 4);
labpc_serial_out(dev, value, 8);
/* set and clear caldac bit to load caldac value */
- devpriv->cmd5 |= CALDAC_LOAD_BIT;
+ devpriv->cmd5 |= CMD5_CALDACLD;
udelay(1);
- devpriv->write_byte(devpriv->cmd5, dev->iobase + COMMAND5_REG);
- devpriv->cmd5 &= ~CALDAC_LOAD_BIT;
+ devpriv->write_byte(devpriv->cmd5, dev->iobase + CMD5_REG);
+ devpriv->cmd5 &= ~CMD5_CALDACLD;
udelay(1);
- devpriv->write_byte(devpriv->cmd5, dev->iobase + COMMAND5_REG);
+ devpriv->write_byte(devpriv->cmd5, dev->iobase + CMD5_REG);
}
static int labpc_calib_insn_write(struct comedi_device *dev,
devpriv->write_byte = labpc_outb;
}
/* initialize board's command registers */
- devpriv->write_byte(devpriv->cmd1, dev->iobase + COMMAND1_REG);
- devpriv->write_byte(devpriv->cmd2, dev->iobase + COMMAND2_REG);
- devpriv->write_byte(devpriv->cmd3, dev->iobase + COMMAND3_REG);
- devpriv->write_byte(devpriv->cmd4, dev->iobase + COMMAND4_REG);
+ devpriv->write_byte(devpriv->cmd1, dev->iobase + CMD1_REG);
+ devpriv->write_byte(devpriv->cmd2, dev->iobase + CMD2_REG);
+ devpriv->write_byte(devpriv->cmd3, dev->iobase + CMD3_REG);
+ devpriv->write_byte(devpriv->cmd4, dev->iobase + CMD4_REG);
if (board->register_layout == labpc_1200_layout) {
- devpriv->write_byte(devpriv->cmd5, dev->iobase + COMMAND5_REG);
- devpriv->write_byte(devpriv->cmd6, dev->iobase + COMMAND6_REG);
+ devpriv->write_byte(devpriv->cmd5, dev->iobase + CMD5_REG);
+ devpriv->write_byte(devpriv->cmd6, dev->iobase + CMD6_REG);
}
/* grab our IRQ */
projects / linux-imx.git / commitdiff