1 /*******************************************************************
2 Components for embedded applications builded for
3 laboratory and medical instruments firmware
5 system_def.h - common cover for definition of hardware adresses,
6 registers, timing and other hardware dependant
7 parts of embedded hardware
9 Copyright (C) 2001 by Pavel Pisa pisa@cmp.felk.cvut.cz
10 (C) 2002 by PiKRON Ltd. http://www.pikron.com
12 *******************************************************************/
14 #ifndef _SYSTEM_DEF_H_
15 #define _SYSTEM_DEF_H_
18 #include <system_stub.h>
21 #include <hal_gpio_def.h>
31 #define VER_CODE(major,minor,patch) (major*0x10000+minor*0x100+patch)
32 /* Software version */
33 #define SW_VER_ID "LMC1"
34 #define SW_VER_MAJOR 0
35 #define SW_VER_MINOR 1
36 #define SW_VER_PATCH 0
37 #define SW_VER_CODE VER_CODE(SW_VER_MAJOR,SW_VER_MINOR,SW_VER_PATCH)
38 /* Hardware version */
39 #define HW_VER_ID "LMC1"
40 #define HW_VER_MAJOR 1
41 #define HW_VER_MINOR 0
42 #define HW_VER_PATCH 0
43 #define HW_VER_CODE VER_CODE(HW_VER_MAJOR,HW_VER_MINOR,HW_VER_PATCH)
44 /* Version of mechanical */
45 #define MECH_VER_ID "LMC1"
46 #define MECH_VER_MAJOR 0
47 #define MECH_VER_MINOR 0
48 #define MECH_VER_PATCH 0
49 #define MECH_VER_CODE VER_CODE(MECH_VER_MAJOR,MECH_VER_MINOR,MECH_VER_PATCH)
52 /*--------------------- Clock Configuration ----------------------------------
54 // <e> Clock Configuration
55 // <h> System Controls and Status Register (SCS)
56 // <o1.4> OSCRANGE: Main Oscillator Range Select
57 // <0=> 1 MHz to 20 MHz
58 // <1=> 15 MHz to 24 MHz
59 // <e1.5> OSCEN: Main Oscillator Enable
63 // <h> Clock Source Select Register (CLKSRCSEL)
64 // <o2.0..1> CLKSRC: PLL Clock Source Selection
65 // <0=> Internal RC oscillator
66 // <1=> Main oscillator
67 // <2=> RTC oscillator
70 // <e3> PLL0 Configuration (Main PLL)
71 // <h> PLL0 Configuration Register (PLL0CFG)
72 // <i> F_cco0 = (2 * M * F_in) / N
73 // <i> F_in must be in the range of 32 kHz to 50 MHz
74 // <i> F_cco0 must be in the range of 275 MHz to 550 MHz
75 // <o4.0..14> MSEL: PLL Multiplier Selection
78 // <o4.16..23> NSEL: PLL Divider Selection
84 // <e5> PLL1 Configuration (USB PLL)
85 // <h> PLL1 Configuration Register (PLL1CFG)
86 // <i> F_usb = M * F_osc or F_usb = F_cco1 / (2 * P)
87 // <i> F_cco1 = F_osc * M * 2 * P
88 // <i> F_cco1 must be in the range of 156 MHz to 320 MHz
89 // <o6.0..4> MSEL: PLL Multiplier Selection
91 // <i> M Value (for USB maximum value is 4)
92 // <o6.5..6> PSEL: PLL Divider Selection
101 // <h> CPU Clock Configuration Register (CCLKCFG)
102 // <o7.0..7> CCLKSEL: Divide Value for CPU Clock from PLL0
106 // <h> USB Clock Configuration Register (USBCLKCFG)
107 // <o8.0..3> USBSEL: Divide Value for USB Clock from PLL1
109 // <i> Divide is USBSEL + 1
112 // <h> Peripheral Clock Selection Register 0 (PCLKSEL0)
113 // <o9.0..1> PCLK_WDT: Peripheral Clock Selection for WDT
114 // <0=> Pclk = Cclk / 4
116 // <2=> Pclk = Cclk / 2
117 // <3=> Pclk = Hclk / 8
118 // <o9.2..3> PCLK_TIMER0: Peripheral Clock Selection for TIMER0
119 // <0=> Pclk = Cclk / 4
121 // <2=> Pclk = Cclk / 2
122 // <3=> Pclk = Hclk / 8
123 // <o9.4..5> PCLK_TIMER1: Peripheral Clock Selection for TIMER1
124 // <0=> Pclk = Cclk / 4
126 // <2=> Pclk = Cclk / 2
127 // <3=> Pclk = Hclk / 8
128 // <o9.6..7> PCLK_UART0: Peripheral Clock Selection for UART0
129 // <0=> Pclk = Cclk / 4
131 // <2=> Pclk = Cclk / 2
132 // <3=> Pclk = Hclk / 8
133 // <o9.8..9> PCLK_UART1: Peripheral Clock Selection for UART1
134 // <0=> Pclk = Cclk / 4
136 // <2=> Pclk = Cclk / 2
137 // <3=> Pclk = Hclk / 8
138 // <o9.12..13> PCLK_PWM1: Peripheral Clock Selection for PWM1
139 // <0=> Pclk = Cclk / 4
141 // <2=> Pclk = Cclk / 2
142 // <3=> Pclk = Hclk / 8
143 // <o9.14..15> PCLK_I2C0: Peripheral Clock Selection for I2C0
144 // <0=> Pclk = Cclk / 4
146 // <2=> Pclk = Cclk / 2
147 // <3=> Pclk = Hclk / 8
148 // <o9.16..17> PCLK_SPI: Peripheral Clock Selection for SPI
149 // <0=> Pclk = Cclk / 4
151 // <2=> Pclk = Cclk / 2
152 // <3=> Pclk = Hclk / 8
153 // <o9.20..21> PCLK_SSP1: Peripheral Clock Selection for SSP1
154 // <0=> Pclk = Cclk / 4
156 // <2=> Pclk = Cclk / 2
157 // <3=> Pclk = Hclk / 8
158 // <o9.22..23> PCLK_DAC: Peripheral Clock Selection for DAC
159 // <0=> Pclk = Cclk / 4
161 // <2=> Pclk = Cclk / 2
162 // <3=> Pclk = Hclk / 8
163 // <o9.24..25> PCLK_ADC: Peripheral Clock Selection for ADC
164 // <0=> Pclk = Cclk / 4
166 // <2=> Pclk = Cclk / 2
167 // <3=> Pclk = Hclk / 8
168 // <o9.26..27> PCLK_CAN1: Peripheral Clock Selection for CAN1
169 // <0=> Pclk = Cclk / 4
171 // <2=> Pclk = Cclk / 2
172 // <3=> Pclk = Hclk / 6
173 // <o9.28..29> PCLK_CAN2: Peripheral Clock Selection for CAN2
174 // <0=> Pclk = Cclk / 4
176 // <2=> Pclk = Cclk / 2
177 // <3=> Pclk = Hclk / 6
178 // <o9.30..31> PCLK_ACF: Peripheral Clock Selection for ACF
179 // <0=> Pclk = Cclk / 4
181 // <2=> Pclk = Cclk / 2
182 // <3=> Pclk = Hclk / 6
185 // <h> Peripheral Clock Selection Register 1 (PCLKSEL1)
186 // <o10.0..1> PCLK_QEI: Peripheral Clock Selection for the Quadrature Encoder Interface
187 // <0=> Pclk = Cclk / 4
189 // <2=> Pclk = Cclk / 2
190 // <3=> Pclk = Hclk / 8
191 // <o10.2..3> PCLK_GPIO: Peripheral Clock Selection for GPIOs
192 // <0=> Pclk = Cclk / 4
194 // <2=> Pclk = Cclk / 2
195 // <3=> Pclk = Hclk / 8
196 // <o10.4..5> PCLK_PCB: Peripheral Clock Selection for the Pin Connect Block
197 // <0=> Pclk = Cclk / 4
199 // <2=> Pclk = Cclk / 2
200 // <3=> Pclk = Hclk / 8
201 // <o10.6..7> PCLK_I2C1: Peripheral Clock Selection for I2C1
202 // <0=> Pclk = Cclk / 4
204 // <2=> Pclk = Cclk / 2
205 // <3=> Pclk = Hclk / 8
206 // <o10.10..11> PCLK_SSP0: Peripheral Clock Selection for SSP0
207 // <0=> Pclk = Cclk / 4
209 // <2=> Pclk = Cclk / 2
210 // <3=> Pclk = Hclk / 8
211 // <o10.12..13> PCLK_TIMER2: Peripheral Clock Selection for TIMER2
212 // <0=> Pclk = Cclk / 4
214 // <2=> Pclk = Cclk / 2
215 // <3=> Pclk = Hclk / 8
216 // <o10.14..15> PCLK_TIMER3: Peripheral Clock Selection for TIMER3
217 // <0=> Pclk = Cclk / 4
219 // <2=> Pclk = Cclk / 2
220 // <3=> Pclk = Hclk / 8
221 // <o10.16..17> PCLK_UART2: Peripheral Clock Selection for UART2
222 // <0=> Pclk = Cclk / 4
224 // <2=> Pclk = Cclk / 2
225 // <3=> Pclk = Hclk / 8
226 // <o10.18..19> PCLK_UART3: Peripheral Clock Selection for UART3
227 // <0=> Pclk = Cclk / 4
229 // <2=> Pclk = Cclk / 2
230 // <3=> Pclk = Hclk / 8
231 // <o10.20..21> PCLK_I2C2: Peripheral Clock Selection for I2C2
232 // <0=> Pclk = Cclk / 4
234 // <2=> Pclk = Cclk / 2
235 // <3=> Pclk = Hclk / 8
236 // <o10.22..23> PCLK_I2S: Peripheral Clock Selection for I2S
237 // <0=> Pclk = Cclk / 4
239 // <2=> Pclk = Cclk / 2
240 // <3=> Pclk = Hclk / 8
241 // <o10.26..27> PCLK_RIT: Peripheral Clock Selection for the Repetitive Interrupt Timer
242 // <0=> Pclk = Cclk / 4
244 // <2=> Pclk = Cclk / 2
245 // <3=> Pclk = Hclk / 8
246 // <o10.28..29> PCLK_SYSCON: Peripheral Clock Selection for the System Control Block
247 // <0=> Pclk = Cclk / 4
249 // <2=> Pclk = Cclk / 2
250 // <3=> Pclk = Hclk / 8
251 // <o10.30..31> PCLK_MC: Peripheral Clock Selection for the Motor Control PWM
252 // <0=> Pclk = Cclk / 4
254 // <2=> Pclk = Cclk / 2
255 // <3=> Pclk = Hclk / 8
258 // <h> Power Control for Peripherals Register (PCONP)
259 // <o11.1> PCTIM0: Timer/Counter 0 power/clock enable
260 // <o11.2> PCTIM1: Timer/Counter 1 power/clock enable
261 // <o11.3> PCUART0: UART 0 power/clock enable
262 // <o11.4> PCUART1: UART 1 power/clock enable
263 // <o11.6> PCPWM1: PWM 1 power/clock enable
264 // <o11.7> PCI2C0: I2C interface 0 power/clock enable
265 // <o11.8> PCSPI: SPI interface power/clock enable
266 // <o11.9> PCRTC: RTC power/clock enable
267 // <o11.10> PCSSP1: SSP interface 1 power/clock enable
268 // <o11.12> PCAD: A/D converter power/clock enable
269 // <o11.13> PCCAN1: CAN controller 1 power/clock enable
270 // <o11.14> PCCAN2: CAN controller 2 power/clock enable
271 // <o11.15> PCGPIO: GPIOs power/clock enable
272 // <o11.16> PCRIT: Repetitive interrupt timer power/clock enable
273 // <o11.17> PCMC: Motor control PWM power/clock enable
274 // <o11.18> PCQEI: Quadrature encoder interface power/clock enable
275 // <o11.19> PCI2C1: I2C interface 1 power/clock enable
276 // <o11.21> PCSSP0: SSP interface 0 power/clock enable
277 // <o11.22> PCTIM2: Timer 2 power/clock enable
278 // <o11.23> PCTIM3: Timer 3 power/clock enable
279 // <o11.24> PCUART2: UART 2 power/clock enable
280 // <o11.25> PCUART3: UART 3 power/clock enable
281 // <o11.26> PCI2C2: I2C interface 2 power/clock enable
282 // <o11.27> PCI2S: I2S interface power/clock enable
283 // <o11.29> PCGPDMA: GP DMA function power/clock enable
284 // <o11.30> PCENET: Ethernet block power/clock enable
285 // <o11.31> PCUSB: USB interface power/clock enable
290 #define CLOCK_SETUP 1
292 #define SCS_Val 0x00000020 /* OSCEN */
293 #define CLKSRCSEL_Val 0x00000001 /* XTAL */
296 #define PLL0CFG_Val 0x0000000B /* 288000000Hz - must be in the range 275HMz-550MHz */
299 #define PLL1CFG_Val 0x00000023
301 #define CCLKCFG_Val 0x00000003 /* ppl0clk/(CCLKCFG_Val+1)=72000000Hz */
302 #define USBCLKCFG_Val 0x00000005 /* divide ppl0clk by 6 to 48MHz */
304 //#define PCLKSEL0_Val 0x00000000 /* all peripherial sysclk/4 */
305 //#define PCLKSEL1_Val 0x00000000
306 //#define PCONP_Val 0x042887DE
308 #define PCONP_CLK_DIV(x) ((x)==0?4:((x)==1?1:((x)==2?2:8)))
310 /*--------------------- Flash Accelerator Configuration ----------------------
312 // <e> Flash Accelerator Configuration
313 // <o1.0..1> FETCHCFG: Fetch Configuration
314 // <0=> Instruction fetches from flash are not buffered
315 // <1=> One buffer is used for all instruction fetch buffering
316 // <2=> All buffers may be used for instruction fetch buffering
317 // <3=> Reserved (do not use this setting)
318 // <o1.2..3> DATACFG: Data Configuration
319 // <0=> Data accesses from flash are not buffered
320 // <1=> One buffer is used for all data access buffering
321 // <2=> All buffers may be used for data access buffering
322 // <3=> Reserved (do not use this setting)
323 // <o1.4> ACCEL: Acceleration Enable
324 // <o1.5> PREFEN: Prefetch Enable
325 // <o1.6> PREFOVR: Prefetch Override
326 // <o1.12..15> FLASHTIM: Flash Access Time
327 // <0=> 1 CPU clock (for CPU clock up to 20 MHz)
328 // <1=> 2 CPU clocks (for CPU clock up to 40 MHz)
329 // <2=> 3 CPU clocks (for CPU clock up to 60 MHz)
330 // <3=> 4 CPU clocks (for CPU clock up to 80 MHz)
331 // <4=> 5 CPU clocks (for CPU clock up to 100 MHz)
332 // <5=> 6 CPU clocks (for any CPU clock)
335 #define FLASH_SETUP 1
336 #define FLASHCFG_Val 0x0000403A
338 /*----------------------------------------------------------------------------
340 *----------------------------------------------------------------------------*/
341 #define XTAL (12000000UL) /* Oscillator frequency */
342 #define OSC_CLK ( XTAL) /* Main oscillator frequency */
343 #define RTC_CLK ( 32000UL) /* RTC oscillator frequency */
344 #define IRC_OSC ( 4000000UL) /* Internal RC oscillator frequency */
346 #define SYS_TIMER_HZ 1000
349 #define BIT(n) (1 << (n))
352 // Port Bit Definitions & Macros: Description - initial conditions
353 #define CAN1_RX_BIT BIT(0) // CAN1 RX
354 #define CAN1_TX_BIT BIT(1) // CAN1 TX
355 #define TXD0_BIT BIT(2) // used by UART0
356 #define RXD0_BIT BIT(3) // used by UART0
357 #define CAN2_RX_BIT BIT(4) // CAN2 RX
358 #define CAN2_TX_BIT BIT(5) // CAN2 TX
359 #define LED2_BIT BIT(6) // active low/SSEL1
360 #define LED2_PIN PORT_PIN(0,6,PORT_CONF_GPIO_OUT_LO)
361 #define SSP1_CS0_BIT BIT(6) // active low/ LMC_GRAD CS
362 #define SSP1_CS0_PIN PORT_PIN(0,6,PORT_CONF_GPIO_OUT_HI)
363 #define SCK1_BIT BIT(7) // clock SSP1 to gradient valves
364 #define SCK1_PIN PORT_PIN(0,7,PORT_CONF_FNC_2|PORT_CONF_OUT_LO_NORM)
365 #define MISO1_BIT BIT(8) // master input
366 #define MISO1_PIN PORT_PIN(0,8,PORT_CONF_FNC_2|PORT_CONF_IN_PU)
367 #define MOSI1_BIT BIT(9) // master output
368 #define MOSI1_PIN PORT_PIN(0,9,PORT_CONF_FNC_2|PORT_CONF_OUT_LO_NORM)
369 #define P0_10_UNUSED_BIT BIT(10) // P0.10 unused (SDA2/TXD2)
370 #define P0_11_UNUSED_BIT BIT(11) // P0.11 unused (SCL2/RXD2)
371 #define SCK0_BIT BIT(15) // clock SSP0 to display panel
372 #define SCK0_PIN PORT_PIN(0,15,PORT_CONF_FNC_2|PORT_CONF_OUT_LO_NORM)
373 #define SSEL0_BIT BIT(16) // slave select SSP0
374 #define SSP0_CS0_BIT BIT(16) // slave select SSP0 / display chip select
375 #define SSP0_CS0_PIN PORT_PIN(0,16,PORT_CONF_GPIO_OUT_HI)
376 #define MISO0_BIT BIT(17) // master input SSP0
377 #define MISO0_PIN PORT_PIN(0,17,PORT_CONF_FNC_2|PORT_CONF_IN_PU)
378 #define MOSI0_BIT BIT(18) // master output SSP0
379 #define MOSI0_PIN PORT_PIN(0,18,PORT_CONF_FNC_2|PORT_CONF_OUT_LO_NORM)
380 #define SDA1_BIT BIT(19) // I2C data - memory/connector
381 #define SCL1_BIT BIT(20) // I2C clock
382 #define SSP0_CS1_BIT BIT(21) // chip select 1 SSP0/ A/D for display
383 #define SSP0_CS1_PIN PORT_PIN(0,21,PORT_CONF_GPIO_OUT_HI)
384 #define SSP0_CS2_BIT BIT(22) // chip select 2 SSP0 for keyboard and LED
385 #define SSP0_CS2_PIN PORT_PIN(0,22,PORT_CONF_GPIO_OUT_HI)
386 #define ADC0_BIT BIT(23) // ADC motor current
387 #define ADC1_BIT BIT(24) // ADC motor current
388 #define ADC2_BIT BIT(25) // ADC motor current
389 #define ADC3_BIT BIT(26) // ADC motor current
390 #define P0_27_UNUSED_BIT BIT(27) // P0.27 unused
391 #define P0_28_UNUSED_BIT BIT(28) // P0.28 unused
392 #define USBDPLUS_BIT BIT(29) // P0.29 USBD+
393 #define USBDMINUS_BIT BIT(30) // P0.30 USBD-
396 // Port Bit Definitions & Macros: Description - initial conditions
398 #define P1_ETH_BITS (BIT(0)|BIT(1)|BIT(4)|BIT(8)|BIT(9)|\
399 BIT(10)|BIT(14)|BIT(15)|BIT(16)|BIT(17))
401 #define P1_0_UNUSED_BIT BIT(0) // P1.0 unused - low output
402 #define P1_1_UNUSED_BIT BIT(1) // P1.1 unused - low output
403 #define P1_4_UNUSED_BIT BIT(4) // P1.4 unused - low output
404 #define P1_8_UNUSED_BIT BIT(8) // P1.8 unused - low output
405 #define P1_9_UNUSED_BIT BIT(9) // P1.9 unused - low output
406 #define P1_10_UNUSED_BIT BIT(10) // P1.10 unused - low output
407 #define P1_14_UNUSED_BIT BIT(14) // P1.14 unused - low output
408 #define P1_15_UNUSED_BIT BIT(15) // P1.15 unused - low output
409 #define PWM1_BIT BIT(18) // motor pwm 0 / ADC0
410 #define PWM1_PIN PORT_PIN(1,18,PORT_CONF_FNC_2|PORT_CONF_OUT_LO_NORM)
411 #define BLDC_HAL_A_BIT BIT(19) // motor HAL input A
412 #define BLDC_HAL_A_PIN PORT_PIN(1,19,PORT_CONF_GPIO_IN_PU)
413 #define IRC_A_BIT BIT(20) // motor IRC channel A (MCI0)
414 #define IRC_M_BIT BIT(21) // motor IRC channel mark (GPIO)
415 #define BLDC_HAL_B_BIT BIT(22) // motor HAL input B
416 #define BLDC_HAL_B_PIN PORT_PIN(1,22,PORT_CONF_GPIO_IN_PU)
417 #define IRC_B_BIT BIT(23) // motor IRC channel B (MCI1)
418 #define IRC_I_BIT BIT(24) // motor IRC index (MCI2)
419 #define BLDC_HAL_C_BIT BIT(25) // motor HAL input C
420 #define BLDC_HAL_C_PIN PORT_PIN(1,25,PORT_CONF_GPIO_IN_PU)
421 #define PWM1_EN_BIT BIT(26) // motor pwm 0 enable
422 #define PWM1_EN_PIN PORT_PIN(1,26,PORT_CONF_GPIO_OUT_LO)
423 #define PWM2_EN_BIT BIT(27) // motor pwm 1 enable
424 #define PWM2_EN_PIN PORT_PIN(1,27,PORT_CONF_GPIO_OUT_LO)
425 #define PWM4_EN_BIT BIT(28) // motor pwm 2 enable
426 #define PWM4_EN_PIN PORT_PIN(1,28,PORT_CONF_GPIO_OUT_LO)
427 #define PWM6_EN_BIT BIT(29) // motor pwm 3 enable
428 #define PWM6_EN_PIN PORT_PIN(1,29,PORT_CONF_GPIO_OUT_LO)
429 #define ADC4_BIT BIT(30) // ADC4 tensometer
430 #define ADC5_BIT BIT(31) // ADC5 external input
432 // Port Bit Definitions & Macros: Description - initial conditions
433 #define TXD1_BIT BIT(0) // P2.0 TXD
434 #define RXD1_BIT BIT(1) // P2.1 RXD
435 #define CTS1_BIT BIT(2) // P2.2 CTS connected to RXD1
436 #define PWM4_BIT BIT(3) // P2.3 motor pwm 2 / ADC2
437 #define PWM4_PIN PORT_PIN(2,3,PORT_CONF_FNC_1|PORT_CONF_OUT_LO_NORM)
438 #define DSR1_BIT BIT(4) // P2.4 DSR connected to TXD1
439 #define PWM6_BIT BIT(5) // P2.5 motor pwm 3 / ADC3
440 #define PWM6_PIN PORT_PIN(2,5,PORT_CONF_FNC_1|PORT_CONF_OUT_LO_NORM)
441 #define LED1_BIT BIT(6) // P2.6 LED1 - error
442 #define LED1_PIN PORT_PIN(2,6,PORT_CONF_GPIO_OUT_LO)
443 #define RTS1_BIT BIT(7) // P2.7 RTS1 used as DIR1
444 #define AUX_OUT2_BIT BIT(8) // P2.8 auxual TLL port
445 #define USB_CONNECT_BIT BIT(9) // P2.9 USB output for soft connect
446 #define BOOT_BIT BIT(10) // P2.10 Boot input
447 #define AUX_IN2_BIT BIT(11) // P2.11 auxual TLL port
448 #define AUX_OUT4_BIT BIT(12) // P2.12 auxual TLL port
449 #define ETH_PD_IRQ_BIT BIT(13) // P2.13 power down/int
451 // Port Bit Definitions & Macros: Description - initial conditions
452 #define PWM2_BIT BIT(25) // P3.25 motor pwm 1 / ADC1
453 #define PWM2_PIN PORT_PIN(3,25,PORT_CONF_FNC_3|PORT_CONF_OUT_LO_NORM)
454 #define AUX_OUT1_BIT BIT(26) // P3.26 auxual TLL port
456 // Port Bit Definitions & Macros: Description - initial conditions
457 #define AUX_OUT3_BIT BIT(28) // P4.28 auxual TLL port / TXD3
458 #define AUX_IN1_BIT BIT(29) // P4.29 auxual TLL port / RXD3
460 #define P0IO_INPUT_BITS (uint32_t) ( \
478 #define P1IO_INPUT_BITS (uint32_t) ( \
491 #define P2IO_INPUT_BITS (uint32_t) ( \
500 #define P3IO_INPUT_BITS (uint32_t) ( \
503 #define P4IO_INPUT_BITS (uint32_t) ( \
507 #define P0IO_ZERO_BITS (uint32_t) ( \
512 #define P1IO_ZERO_BITS (uint32_t) ( \
520 #define P2IO_ZERO_BITS (uint32_t) ( \
525 #define P3IO_ZERO_BITS (uint32_t) ( \
529 #define P4IO_ZERO_BITS (uint32_t) ( \
532 #define P0IO_ONE_BITS (uint32_t) ( \
546 #define P1IO_ONE_BITS (uint32_t) ( \
549 #define P2IO_ONE_BITS (uint32_t) ( \
558 #define P3IO_ONE_BITS (uint32_t) ( \
562 #define P4IO_ONE_BITS (uint32_t) ( \
566 #define P0IO_OUTPUT_BITS (uint32_t) ( \
570 #define P1IO_OUTPUT_BITS (uint32_t) ( \
574 #define P2IO_OUTPUT_BITS (uint32_t) ( \
578 #define P3IO_OUTPUT_BITS (uint32_t) ( \
582 #define P4IO_OUTPUT_BITS (uint32_t) ( \
588 /***************************************************************************/
590 #define LED_GP LED2_BIT /* GENREAL PURPOSE LED */
591 #define LED_ERR LED1_BIT
593 /***************************************************************************/
595 #define IN_PORT GPIO0->FIO
596 #define OUT_PORT GPIO1->FIO
597 #define LED_PORT GPIO2->FIO
599 #define CREATE_PORT_NAME_PIN(port) port##PIN
600 #define CREATE_PORT_NAME_CLR(port) port##CLR
601 #define CREATE_PORT_NAME_SET(port) port##SET
603 #define GET_IN_PIN(port,in) ((CREATE_PORT_NAME_PIN(port) & in)?1:0)
604 #define GET_IN_PORT(port) (CREATE_PORT_NAME_PIN(port))
605 #define SET_OUT_PIN(port,out) (CREATE_PORT_NAME_SET(port)=out)
606 #define CLR_OUT_PIN(port,out) (CREATE_PORT_NAME_CLR(port)=out)
608 /***************************************************************************/
610 #define WATCHDOG_ENABLED
611 #define WATCHDOG_TIMEOUT_MS 1000
613 /***************************************************************************/
614 /* uLan configuration */
620 #ifdef ULD_DEFAULT_BUFFER_SIZE
621 #undef ULD_DEFAULT_BUFFER_SIZE
622 #define ULD_DEFAULT_BUFFER_SIZE 0x2000
625 #define UL_DRV_SYSLESS_PORT UART1_BASE
626 #define UL_DRV_SYSLESS_BAUD 19200
627 #define UL_DRV_SYSLESS_IRQ UART1_IRQn
628 #define UL_DRV_SYSLESS_MY_ADR_DEFAULT 1
630 #define watchdog_feed lpc_watchdog_feed
631 #define kvpb_erase lpcisp_kvpb_erase
632 #define kvpb_copy lpcisp_kvpb_copy
633 #define kvpb_flush lpcisp_kvpb_flush
634 #define KVPB_DEFAULT_FLAGS KVPB_DESC_DOUBLE|KVPB_DESC_CHUNKWO
636 /***************************************************************************/
637 /* USB configuration */
638 #define USB_WITH_UDEV_FNC
639 #define USB_EP_NUM 32
640 #define USB_MAX_PACKET0 64
641 #define USB_MAX_PACKET 8
642 #define USB_DMA_EP 0x00000000
644 #define USB_VBUS_PIN_USED 0
646 /***************************************************************************/
647 /* I2C1 configuration */
648 #define I2C_DRV_SYSLESS_IRQ I2C1_IRQn
649 #define I2C_DRV_SYSLESS_PORT I2C1_BASE
650 #define I2C_DRV_SYSLESS_BITRATE 10000
651 #define I2C_DRV_SYSLESS_SLADR 0
653 #endif /* _SYSTEM_DEF_H_ */