endif
config CAN_DEV
- tristate "Prompt for platform CAN drivers with sysfs support"
+ tristate "Prompt for platform CAN drivers with netlink support"
depends on CAN && SYSFS
default Y
---help---
support. This is the standard library for CAN drivers.
If unsure, say Y.
+config CAN_DEV_SYSFS
+ bool "Support for sysfs interface (deprecated)"
+ depends on CAN_DEV && SYSFS
+ default N
+ ---help---
+ Adds support for the legacy sysfs interface to configure CAN
+ devices. If possible, please use the new netlink interface
+ instead.
+ If unsure, say N.
+
config CAN_CALC_BITTIMING
bool "CAN bit-timing calculation"
depends on CAN_DEV
files "tq", "prop_seg", "phase_seg1", "phase_seg2" and "sjw".
If unsure, say Y.
+config CAN_CC770
+ depends on HAS_IOMEM && CAN_DEV
+ tristate "Bosch CC770 and Intel AN82527"
+ ---help---
+ Driver for the Bosch CC770 and the compatible Intel AN82527
+ CAN controllers.
+
+config CAN_CC770_ISA
+ depends on CAN_CC770 && ISA
+ tristate "ISA Bus based legacy CC770 driver"
+ ---help---
+ This driver adds legacy support for CC770 and AN82527 chips
+ connected to the ISA bus using I/O port, memory mapped or
+ indirect access.
+
+config CAN_CC770_OF_PLATFORM
+ depends on CAN_CC770 && PPC_OF
+ tristate "Generic OF Platform Bus based CC770 driver"
+ ---help---
+ This driver adds support for the CC770 and other AN82527
+ compatible chips connected to the OpenFirmware "platform bus"
+ found on embedded systems with OpenFirmware bindings, e.g. if
+ you have a PowerPC based system you may want to enable this
+ option.
+
config CAN_SJA1000
depends on CAN_DEV
tristate "Philips SJA1000"
---help---
- The SJA1000 is one of the top CAN controllers out there. As it
- has a multiplexed interface it fits directly to 8051
- microcontrollers or into the PC I/O port space. The SJA1000
- is a full CAN controller, with shadow registers for RX and TX.
- It can send and receive any kinds of CAN frames (SFF/EFF/RTR)
- with a single (simple) filter setup.
+ Driver for the SJA1000 CAN controllers from Philips or NXP
- This driver will use the new device interface.
+config CAN_SJA1000_ISA
+ depends on CAN_SJA1000 && ISA
+ tristate "ISA Bus based legacy SJA1000 driver"
+ ---help---
+ This driver adds legacy support for SJA1000 chips connected to
+ the ISA bus using I/O port, memory mapped or indirect access.
config CAN_SJA1000_PLATFORM
depends on CAN_SJA1000
config CAN_SJA1000_OF_PLATFORM
depends on CAN_SJA1000 && PPC_OF
- tristate "generic OF Platform Bus based SJA1000 driver"
+ tristate "Generic OF Platform Bus based SJA1000 driver"
---help---
This driver adds support for the SJA1000 chips connected to
the OpenFirmware "platform bus" found on embedded systems with
OpenFirmware bindings, e.g. if you have a PowerPC based system
- you should enable this option.
+ you may want to enable this option.
config CAN_EMS_PCI
- tristate "EMS CPC-PCI and CPC-PCIe Card"
+ tristate "EMS CPC-PCI, CPC-PCIe and CPC-104P Card"
depends on PCI && CAN_SJA1000
---help---
- This driver is for the one or two channel CPC-PCI and CPC-PCIe
- cards from EMS Dr. Thomas Wuensche (http://www.ems-wuensche.de).
+ This driver is for the one, two or four channel CPC-PCI,
+ CPC-PCIe and CPC-104P cards from EMS Dr. Thomas Wuensche
+ (http://www.ems-wuensche.de).
config CAN_EMS_PCMCIA
tristate "EMS CPC-CARD Card"
This driver is for the one or two channel CPC-CARD cards from
EMS Dr. Thomas Wuensche (http://www.ems-wuensche.de).
+config CAN_EMS_104M
+ tristate "EMS CPC-104M Card"
+ depends on ISA && CAN_SJA1000
+ ---help---
+ This driver is for the one, two or four channel CPC-104M cards
+ from EMS Dr. Thomas Wuensche (http://www.ems-wuensche.de).
+
config CAN_ESD_PCI
tristate "ESD PCI Cards"
depends on PCI && CAN_SJA1000
---help---
- This driver supports the esd PCI CAN cards CAN-PCI/200,
- CAN-PCI/266, CAN-PMC/266 (PMC), CAN-CPCI/200 (CompactPCI),
- CAN-PCIe2000 (PCI Express) and CAN-PCI104/200 (PCI104)
+ This driver supports the esd PCI CAN cards CAN-PCI/200,
+ CAN-PCI/266, CAN-PMC/266 (PMC), CAN-CPCI/200 (CompactPCI),
+ CAN-PCIe2000 (PCI Express) and CAN-PCI104/200 (PCI104)
from the esd electronic system design gmbh (http://www.esd.eu).
config CAN_IXXAT_PCI
This driver is for the the PCIcanx and PCIcan cards (1, 2 or
4 channel) from Kvaser (http://www.kvaser.com).
+config CAN_ESD_PCI331
+ tristate "ESD CAN 331 Cards"
+ depends on PCI && CAN_DEV
+ ---help---
+ This driver supports the PCI/331, CPCI/331 and PMC/331 CAN cards
+ from the esd system design gmbh (http://www.esd.eu).
+
config CAN_SOFTING
tristate "Softing Gmbh CAN generic support"
depends on CAN_DEV
---help---
generic softing CAN cards
+ Sofing CAN cards come with 1 or 2 physical busses.
+ The API of the card does not allow fine control per bus, but
+ controls the 2 busses on the card together.
+ As such, some actions (start/stop/busoff recovery) on 1 bus
+ must bring down the other bus too temporarily.
+ You have been warned.
+ This driver is written on safe on 64bit, but not on big endian.
config CAN_SOFTING_CS
tristate "Softing CAN pcmcia cards"
depends on CAN_SOFTING && PCMCIA
+ ---help---
+ Support for PCMCIA cards from Softing Gmbh & some cards
+ from Vector Gmbh.
+ You need firmware for these, which you can get at
+ http://developer.berlios.de/projects/socketcan/
+ This version of the driver is written against
+ firmware version 4.6
config CAN_MSCAN
depends on CAN_DEV && (PPC || M68K || M68KNOMMU)
projects / socketcan-devel.git / blobdiff