Changelog:
Processing rpp_can_rx/CAN Receive
Processing rpp_can_setup/CAN Setup
Processing rpp_can_tx/CAN Transmit
Processing rpp_gio_in/General Purpose Digital Input
diff --git a/sfunction_gio_in.MaskDescription.old b/sfunction_gio_in.MaskDescription.new
index
208dfe5..
5be5fdc 100644
--- a/sfunction_gio_in.MaskDescription.old
+++ b/sfunction_gio_in.MaskDescription.new
@@ -1,2 +1,2 @@
<p>Reads[-a-] value from a [-GPIO-]{+GIO+} pin. {+Which pins are supported depends on the target board.+} The [-block supports GIOA, GIOB and NHET1 ports. Any-]{+selected+} pin can be configured as tri-state, pull up or pull down.</p>
[-<p>It is not allowed to read from one-]{+<p>When the+} pin[-by using more then one GIOIN blocks. It-] is [-not allowed to use-]{+used in multiple+} GIOIN [-and DOUT blocks together configured for one GPIO pin.</p>-]{+or GIOOUT blocks, an error is signaled.</p>+}
diff --git a/sfunction_gio_in.MaskHelp.old b/sfunction_gio_in.MaskHelp.new
index
208dfe5..
5be5fdc 100644
--- a/sfunction_gio_in.MaskHelp.old
+++ b/sfunction_gio_in.MaskHelp.new
@@ -1,2 +1,2 @@
<p>Reads[-a-] value from a [-GPIO-]{+GIO+} pin. {+Which pins are supported depends on the target board.+} The [-block supports GIOA, GIOB and NHET1 ports. Any-]{+selected+} pin can be configured as tri-state, pull up or pull down.</p>
[-<p>It is not allowed to read from one-]{+<p>When the+} pin[-by using more then one GIOIN blocks. It-] is [-not allowed to use-]{+used in multiple+} GIOIN [-and DOUT blocks together configured for one GPIO pin.</p>-]{+or GIOOUT blocks, an error is signaled.</p>+}
[
\bWarning: an error occurred while parsing class fxptui.explorer:
Invalid data type.
]
\b
Processing rpp_gio_out/General Purpose Digital Output
diff --git a/sfunction_gio_out.MaskDescription.old b/sfunction_gio_out.MaskDescription.new
index
8c37163..
63ee0cb 100644
--- a/sfunction_gio_out.MaskDescription.old
+++ b/sfunction_gio_out.MaskDescription.new
@@ -1,2 +1,2 @@
[-<p>Writes-]{+<p>Sets+} a [-value-]{+GIO pin+} to a [-GPIO pin. The block supports GIOA, GIOB and NHET1 ports.-]{+given value. Which pins are supported depends on the target board.+} Any pin can be configured as open drain or push/pull and initial output value can be specified. The initial value is a value, which will appear on the pin when the GPIO module is initialized and stays there until the first block execution.</p>
[-<p>It is not allowed to write to one-]{+<p>When the+} pin[-by using more then one GIOOUT blocks. It-] is [-not allowed to use-]{+used in multiple GIOIN or+} GIOOUT [-and DIN blocks on one GPIO pin.</p>-]{+blocks, an error is signaled.</p>+}
diff --git a/sfunction_gio_out.MaskHelp.old b/sfunction_gio_out.MaskHelp.new
index
8c37163..
63ee0cb 100644
--- a/sfunction_gio_out.MaskHelp.old
+++ b/sfunction_gio_out.MaskHelp.new
@@ -1,2 +1,2 @@
[-<p>Writes-]{+<p>Sets+} a [-value-]{+GIO pin+} to a [-GPIO pin. The block supports GIOA, GIOB and NHET1 ports.-]{+given value. Which pins are supported depends on the target board.+} Any pin can be configured as open drain or push/pull and initial output value can be specified. The initial value is a value, which will appear on the pin when the GPIO module is initialized and stays there until the first block execution.</p>
[-<p>It is not allowed to write to one-]{+<p>When the+} pin[-by using more then one GIOOUT blocks. It-] is [-not allowed to use-]{+used in multiple GIOIN or+} GIOOUT [-and DIN blocks on one GPIO pin.</p>-]{+blocks, an error is signaled.</p>+}
Processing rpp_hdk_ain/Analog Input
Processing rpp_overrun/Overrun Detection
Processing rpp_sci_cfg/Serial Configure
Processing rpp_sci_printf/Serial Printf
Processing rpp_sci_rx/Serial Receive
Processing rpp_sci_tx/Serial Send