/* m437.c
* Linux CAN-bus device driver.
* Written by Arnaud Westenberg email:arnaud@wanadoo.nl
+ * Rewritten for new CAN queues by Pavel Pisa - OCERA team member
+ * email:pisa@cmp.felk.cvut.cz
* This software is released under the GPL-License.
- * Version 0.7 6 Aug 2001
- */
+ * Version lincan-0.3 17 Jun 2004
+ *
+ * 15 July 2008 updated by Philippe Corbes, email:philippe.corbes@logibag.com
+ * This driver has been designed to support "Memory (MEM)" mode.
+ * For example: Memory, MEM:0xD0000 => io=0xD0000.
+ * Configure the card with m437set.com provided by seco before loading driver.
+ * This software is released under the GPL-License.
+ */
-/*
- * Support for the SECO M437
- *
+/*
+ * Support for the SECO M437
+ *
* SECO M437 is a pc104 format, i82527 controller based card
- * produced by SECO http://www.seco.it
+ * produced by SECO http://www.seco.it
* This driver uses the Memory Mapped I/O mode, and should be
* working with all cards supporting this mode.
*
*
*/
-#include <linux/autoconf.h>
-#if defined (CONFIG_MODVERSIONS) && !defined (MODVERSIONS)
-#define MODVERSIONS
-#endif
-
-#ifdef MODVERSIONS
-#include <linux/modversions.h>
-#endif
-
-#include <linux/ioport.h>
-#include <linux/delay.h>
-#include <asm/errno.h>
-#include <asm/io.h>
-
+#include "../include/can.h"
+#include "../include/can_sysdep.h"
#include "../include/main.h"
#include "../include/m437.h"
#include "../include/i82527.h"
#define IO_RANGE 0x100
-static long base = 0L;
-
/**
- * m437_request_io: - reserve io memory
- * @io_addr: The reserved memory starts at @io_addr, wich is the module
- * parameter @io.
+ * m437_request_io: - reserve io or memory range for can board
+ * @candev: pointer to candevice/board which asks for io. Field @io_addr
+ * of @candev is used in most cases to define start of the range
*
* The function m437_request_io() is used to reserve the io-memory. If your
* hardware uses a dedicated memory range as hardware control registers you
- * will have to add the code to reserve this memory as well.
+ * will have to add the code to reserve this memory as well.
* %IO_RANGE is the io-memory range that gets reserved, please adjust according
* your hardware. Example: #define IO_RANGE 0x100 for i82527 chips or
* #define IO_RANGE 0x20 for sja1000 chips in basic CAN mode.
* Return Value: The function returns zero on success or %-ENODEV on failure
* File: src/m437.c
*/
-int m437_request_io(unsigned long io_addr)
+int m437_request_io(struct candevice_t *candev)
{
+ can_ioptr_t remap_addr;
- if ( !( base = (long) ioremap( io_addr, IO_RANGE ) ) ) {
- CANMSG("Unable to access I/O memory at: 0x%lx\n", io_addr);
+ if (!can_request_mem_region(candev->io_addr,IO_RANGE,DEVICE_NAME)) {
+ CANMSG("M437 Unable to request IO-memory: 0x%lx\n",candev->io_addr);
return -ENODEV;
-
}
- DEBUGMSG("Registered IO-memory: 0x%lx - 0x%lx\n", io_addr, io_addr + IO_RANGE - 1);
+
+ if ( !( remap_addr = ioremap( candev->io_addr, IO_RANGE ) ) ) {
+ CANMSG("M437 Unable to access I/O memory at: 0x%lx\n", candev->io_addr);
+ can_release_mem_region(candev->io_addr,IO_RANGE);
+ return -ENODEV;
+
+ }
+ CANMSG("M437 Registered IO-memory: 0x%lx - 0x%lx\n",
+ candev->io_addr, candev->io_addr + IO_RANGE - 1);
+ CANMSG("M437 IO-memory: 0x%lx Remapped to: 0x%lx\n",
+ (unsigned long)candev->io_addr, (unsigned long)remap_addr);
+
+ /* remap the chip and pointers on objects */
+ can_base_addr_fixup(candev, remap_addr);
+
+#ifdef CAN_DEBUG
+ {
+ int objnr;
+ for (objnr=0; objnr<15 ; objnr++) {
+ DEBUGMSG("M437 Message%d remapped to: 0x%lx\n", objnr+1, candev->chip[0]->msgobj[objnr]->obj_base_addr);
+ }
+ }
+#endif /*CAN_DEBUG*/
+
return 0;
}
/**
- * m437_release_io - free reserved io-memory
- * @io_addr: Start of the memory range to be released.
+ * m437_elease_io - free reserved io memory range
+ * @candev: pointer to candevice/board which releases io
*
* The function m437_release_io() is used to free reserved io-memory.
* In case you have reserved more io memory, don't forget to free it here.
* Return Value: The function always returns zero
* File: src/m437.c
*/
-int m437_release_io(unsigned long io_addr)
+int m437_release_io(struct candevice_t *candev)
{
+ /*
+ * The full board reset is more robust solution
+ * than reset of communication objects
+ * Philippe Corbes, 06 jun 2008
+ */
+#if 0 /* Object reset method */
unsigned i;
/* disable IRQ generation */
- m437_write_register(iCTL_CCE, iCTL);
+ m437_write_register(iCTL_CCE, candev->dev_base_addr+iCTL);
/* clear all message objects */
for (i=1; i<=15; i++) {
RXIE_RES |
TXIE_RES |
MVAL_RES,
- i*0x10+iMSGCTL0);
+ candev->dev_base_addr+i*0x10+iMSGCTL0);
m437_write_register(
NEWD_RES |
MLST_RES |
CPUU_RES |
TXRQ_RES |
RMPD_RES,
- i*0x10+iMSGCTL1);
+ candev->dev_base_addr+i*0x10+iMSGCTL1);
}
-
+
/* power down i82527 */
- m437_write_register(iCPU_PWD, iCPU);
-
+ m437_write_register(iCPU_PWD, candev->dev_base_addr+iCPU);
+
+#else /* Full board reset */
+ m437_reset(candev);
+#endif /* Full board reset */
+
/* release I/O memory mapping */
- iounmap((void*)base);
+ iounmap(candev->dev_base_addr);
+
+ can_release_mem_region(candev->io_addr,IO_RANGE);
+
+ CANMSG("M437 release - OK\n");
return 0;
}
/**
* m437_reset - hardware reset routine
- * @card: Number of the hardware card.
+ * @candev: Pointer to candevice/board structure
*
- * The function m437_reset() is used to give a hardware reset. This is
- * rather hardware specific so I haven't included example code. Don't forget to
+ * The function m437_reset() is used to give a hardware reset. This is
+ * rather hardware specific so I haven't included example code. Don't forget to
* check the reset status of the chip before returning.
* Return Value: The function returns zero on success or %-ENODEV on failure
* File: src/m437.c
+ * from Philippe Corbes, 08 July 2008
*/
-int m437_reset(int card)
+int m437_reset(struct candevice_t *candev)
{
+ int i=0;
+
+ DEBUGMSG("Resetting %s hardware ...\n", candev->hwname);
+ for (i = 0 ; i < 10 ; i++) {
+ m437_write_register(0x01,candev->dev_base_addr+candev->res_addr);
+ }
+ m437_write_register(0x0,candev->dev_base_addr+candev->res_addr);
+
+ /* Check hardware reset status */
+ i=0;
+ while ( (m437_read_register(candev->dev_base_addr+iCPU) & iCPU_RST) && (i<=15)) {
+ udelay(20000);
+ i++;
+ }
+ if (i>=15) {
+ CANMSG("M437 Reset status timeout! Please check your hardware.\n");
+ return -ENODEV;
+ }
+ else
+ DEBUGMSG("Chip0 reset status ok.\n");
+
return 0;
}
#define NR_SJA1000 0
/**
- * m437_init_hw_data - Initialze hardware cards
- * @card: Number of the hardware card.
+ * m437_init_hw_data - Initialize hardware cards
+ * @candev: Pointer to candevice/board structure
*
* The function m437_init_hw_data() is used to initialize the hardware
* structure containing information about the installed CAN-board.
* %RESET_ADDR represents the io-address of the hardware reset register.
* %NR_82527 represents the number of intel 82527 chips on the board.
* %NR_SJA1000 represents the number of philips sja1000 chips on the board.
- * The flags entry can currently only be %PROGRAMMABLE_IRQ to indicate that
+ * The flags entry can currently only be %CANDEV_PROGRAMMABLE_IRQ to indicate that
* the hardware uses programmable interrupts.
* Return Value: The function always returns zero
* File: src/m437.c
*/
-int m437_init_hw_data(int card)
+int m437_init_hw_data(struct candevice_t *candev)
{
DEBUGMSG("m437_init_hw_data()\n");
- candevices_p[card]->res_addr=RESET_ADDR;
- candevices_p[card]->nr_82527_chips=1;
- candevices_p[card]->nr_sja1000_chips=0;
- candevices_p[card]->flags &= ~PROGRAMMABLE_IRQ;
+ candev->res_addr=RESET_ADDR;
+ candev->nr_82527_chips=1;
+ candev->nr_sja1000_chips=0;
+ candev->nr_all_chips=1;
+ candev->flags &= ~CANDEV_PROGRAMMABLE_IRQ;
/* The M437 has no programmable IRQ */
return 0;
}
-#define CHIP_TYPE "i82527"
/**
* m437_init_chip_data - Initialize chips
- * @card: Number of the hardware card
+ * @candev: Pointer to candevice/board structure
* @chipnr: Number of the CAN chip on the hardware card
*
* The function m437_init_chip_data() is used to initialize the hardware
* The @clock entry holds the chip clock value in Hz.
* The entry @sja_cdr_reg holds hardware specific options for the Clock Divider
* register. Options defined in the %sja1000.h file:
- * %CDR_CLKOUT_MASK, %CDR_CLK_OFF, %CDR_RXINPEN, %CDR_CBP, %CDR_PELICAN
+ * %sjaCDR_CLKOUT_MASK, %sjaCDR_CLK_OFF, %sjaCDR_RXINPEN, %sjaCDR_CBP, %sjaCDR_PELICAN
* The entry @sja_ocr_reg holds hardware specific options for the Output Control
* register. Options defined in the %sja1000.h file:
- * %OCR_MODE_BIPHASE, %OCR_MODE_TEST, %OCR_MODE_NORMAL, %OCR_MODE_CLOCK,
- * %OCR_TX0_LH, %OCR_TX1_ZZ.
+ * %sjaOCR_MODE_BIPHASE, %sjaOCR_MODE_TEST, %sjaOCR_MODE_NORMAL, %sjaOCR_MODE_CLOCK,
+ * %sjaOCR_TX0_LH, %sjaOCR_TX1_ZZ.
* The entry @int_clk_reg holds hardware specific options for the Clock Out
* register. Options defined in the %i82527.h file:
* %iCLK_CD0, %iCLK_CD1, %iCLK_CD2, %iCLK_CD3, %iCLK_SL0, %iCLK_SL1.
- * The entry @int_bus_reg holds hardware specific options for the Bus
+ * The entry @int_bus_reg holds hardware specific options for the Bus
* Configuration register. Options defined in the %i82527.h file:
* %iBUS_DR0, %iBUS_DR1, %iBUS_DT1, %iBUS_POL, %iBUS_CBY.
* The entry @int_cpu_reg holds hardware specific options for the cpu interface
* Return Value: The function always returns zero
* File: src/m437.c
*/
-int m437_init_chip_data(int card, int chipnr)
+int m437_init_chip_data(struct candevice_t *candev, int chipnr)
{
- candevices_p[card]->chip[chipnr]->chip_type=CHIP_TYPE;
- candevices_p[card]->chip[chipnr]->chip_base_addr=candevices_p[card]->io_addr;
- candevices_p[card]->chip[chipnr]->clock = 16000000;
- candevices_p[card]->chip[chipnr]->int_cpu_reg = iCPU_DSC | iCPU_CEN;
- candevices_p[card]->chip[chipnr]->int_clk_reg =
+ i82527_fill_chipspecops(candev->chip[chipnr]);
+ candev->chip[chipnr]->chip_base_addr=candev->dev_base_addr;
+ candev->chip[chipnr]->clock = 16000000;
+ candev->chip[chipnr]->int_cpu_reg = iCPU_DSC | iCPU_CEN;
+ candev->chip[chipnr]->int_clk_reg =
iCLK_CD0 | iCLK_CD1 | iCLK_CD2 | iCLK_SL0 | iCLK_SL1;
- candevices_p[card]->chip[chipnr]->int_bus_reg = iBUS_CBY;
+ candev->chip[chipnr]->int_bus_reg = iBUS_CBY;
return 0;
}
/**
* m437_init_obj_data - Initialize message buffers
- * @chipnr: Number of the CAN chip
+ * @chip: Pointer to chip specific structure
* @objnr: Number of the message buffer
*
* The function m437_init_obj_data() is used to initialize the hardware
* CAN chip. In case of the sja1000 there's only one message object but on the
* i82527 chip there are 15.
* The code below is for a i82527 chip and initializes the object base addresses
- * The entry @obj_base_addr represents the first memory address of the message
+ * The entry @obj_base_addr represents the first memory address of the message
* object. In case of the sja1000 @obj_base_addr is taken the same as the chips
* base address.
* Unless the hardware uses a segmented memory map, flags can be set zero.
* Return Value: The function always returns zero
* File: src/m437.c
*/
-int m437_init_obj_data(int chipnr, int objnr)
+int m437_init_obj_data(struct canchip_t *chip, int objnr)
{
- chips_p[chipnr]->msgobj[objnr]->obj_base_addr=chips_p[chipnr]->chip_base_addr+(objnr+1)*0x10;
- chips_p[chipnr]->msgobj[objnr]->flags=0;
-
+ chip->msgobj[objnr]->obj_base_addr=chip->chip_base_addr+(objnr+1)*0x10;
+
return 0;
}
/**
* m437_program_irq - program interrupts
- * @card: Number of the hardware card.
+ * @candev: Pointer to candevice/board structure
*
- * The function m437_program_irq() is used for hardware that uses
+ * The function m437_program_irq() is used for hardware that uses
* programmable interrupts. If your hardware doesn't use programmable interrupts
- * you should not set the @candevices_t->flags entry to %PROGRAMMABLE_IRQ and
- * leave this function unedited. Again this function is hardware specific so
+ * you should not set the @candevices_t->flags entry to %CANDEV_PROGRAMMABLE_IRQ and
+ * leave this function unedited. Again this function is hardware specific so
* there's no example code.
* Return value: The function returns zero on success or %-ENODEV on failure
* File: src/m437.c
*/
-int m437_program_irq(int card)
+int m437_program_irq(struct candevice_t *candev)
{
+ DEBUGMSG("M437 Programmable interrupt is not supported by the hardware!\n");
return 0;
}
* Return Value: The function does not return a value
* File: src/m437.c
*/
-void m437_write_register(unsigned char data, unsigned long address)
+void m437_write_register(unsigned data, can_ioptr_t address)
{
- writeb(data,base+address);
+ DEBUGMSG("m437_write_register(@0x%lx=0x%x)\n", address, data);
+ can_writeb(data,address);
}
/**
* Return Value: The function returns the value stored in @address
* File: src/m437.c
*/
-unsigned m437_read_register(unsigned long address)
+unsigned m437_read_register(can_ioptr_t address)
{
- return readb(base+address);
+ unsigned data;
+ data = can_readb(address);
+ DEBUGMSG("m437_read_register(@0x%lx=0x%x)\n", address, data);
+ return data;
}
/* !!! Don't change this function !!! */