arm: zynq: Remove 0x prefixes from cc108

The patch fixing issues reported by DTC:
arch/arm/boot/dts/zynq-cc108.dtb: Warning (unit_address_format): Node
/amba/spi@e000d000/flash@0/partition@0x400000 unit name should not have
leading "0x"
arch/arm/boot/dts/zynq-cc108.dtb: Warning (unit_address_format): Node
/amba/spi@e000d000/flash@0/partition@0x800000 unit name should not have
leading "0x"
arch/arm/boot/dts/zynq-cc108.dtb: Warning (unit_address_format): Node
/amba/spi@e000d000/flash@0/partition@0xc00000 unit name should not have
leading "0x"
arch/arm/boot/dts/zynq-cc108.dtb: Warning (unit_address_format): Node
/amba/spi@e000d000/flash@0/partition@0xd00000 unit name should not have
leading "0x"
arch/arm/boot/dts/zynq-cc108.dtb: Warning (unit_address_format): Node
/amba/spi@e000d000/flash@0/partition@0xf00000 unit name should not have
leading "0x"

Signed-off-by: Michal Simek <michal.simek@xilinx.com>

arm: zynq: Fix eeprom dt nodes

- Use eeprom for node name
- Use atmel compatible string instead of at.
- Add missing labels

Signed-off-by: Michal Simek <michal.simek@xilinx.com>

arm: zynq: Use fixed partitions for spi flash for zc770 xm010

Sync with mainline.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>

arm: zynq: Sync up licenses with mainline kernel

Use different location for SPDX line. Also update dates for new mainline
DTS files.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>

ARM: dts: zynq: Add generic compatible string for I2C EEPROM

The at24 driver allows to register I2C EEPROM chips using different vendor
and devices, but the I2C subsystem does not take the vendor into account
when matching using the I2C table since it only has device entries.

But when matching using an OF table, both the vendor and device has to be
taken into account so the driver defines only a set of compatible strings
using the "atmel" vendor as a generic fallback for compatible I2C devices.

So add this generic fallback to the device node compatible string to make
the device to match the driver using the OF device ID table.

Signed-off-by: Javier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

arm: zynq: Add missing address node name in microzed board

This patch is fixing issue reported by dtc:
arch/arm/boot/dts/zynq-microzed.dtb: Warning (unit_address_vs_reg): Node
/memory has a reg or ranges property, but no unit name

Signed-off-by: Michal Simek <michal.simek@xilinx.com>

arm: zynq: Use i2c-mux instead of i2cswitch for pca9548

i2c muxes should described like this.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>

dt: bindings: Add AMS channels details

This patch adds details of AMS channels to the Device Tree binding
documentation.

Signed-off-by: Manish Narani <mnarani@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

arm64: zynqmp: Fix spi flash partition definition for zc1751 dc2

Using different node name and label partitions as data.
Also use latest compatible strings based on mainline review.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>

arm64: zynqmp: Add eeprom reference to eeprom nodes

Eeprom can contain information which can be used by nvmem drivers.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>

arm64: zynqmp: Use backward compatible string for gem

Add backward compatible string for gem ("cdns,gem").

Signed-off-by: Michal Simek <michal.simek@xilinx.com>

arm64: zynqmp: Use s/_/-/g in node name for zcu102 rev1.0

Follow spec for node names.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>

arm64: zynqmp: Add silabs prefix to u69 for zcu102

Add vendor prefix to si5341.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>

arm64: zynqmp: Use wifi as node name for wl1831 for zcu100

Use standard name for wifi node.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>

arm64: zynqmp: Use 96boards labels for zcu100

Use label for i2c and spi buses.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>

arm64: zynqmp: Sync up pmic with mainline for zcu100

pmic should use pmic as node name.
Also remove comments about setting.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>

arm64: zynqmp: Remove double spaces from dts files

There is no reason to have double spaces for indentation.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>

arm64: zynqmp: Remove additional comments from dts files

Remove additional comments which were removed as the part of upstreaming.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>

arm64: zynqmp: Use keycode from input/input.h

zcu100 could use sw4 as key_power instead of key_down.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>

arm64: zynqmp: Label 8T49n287 as clock-generator

Based on spec clock chips should be labeled as clock-generators.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>

arm64: zynqmp: Enable watchdog on zcu106

It is enabled in mainline that's why enable it here too.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>

arm64: zynqmp: Use atmel prefix instead of at

This changes was done in mainline and this patch is just following it.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>

arm64: zynqmp: Use maxim prefix for all maxim chips

Use vendor prefix for Maxim chips.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>

arm64: zynqmp: Remove u-boot commands from dts files

U-Boot commands shouldn't be the part of kernel DTS files.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>

arm64: zynqmp: Remove number from clock-generator node name

There shouldn't be a number appended based on spec.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>

arm64: zynqmp: Use i2c-mux instead of i2cswitch instead

Based on review from mainline i2c-mux is standard name for i2c switches.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>

arm64: zynqmp: Sync up license with mainline kernel

Mainline Linux kernel has adopted SPDX header license in a different
format then was used before. This patch is syncing it up.

Also update years in License text and remove Nathalie's email because it
is no longer valid.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>

dma: xilinx: Add interlaced support to Xilinx Framebuffer driver

Adds support for reading or setting the field id of framebuffer written
to memory or read back from memory in the Xilinx Framebuffer driver.

Signed-off-by: Vishal Sagar <vsagar@xilinx.com>
Reviewed-by: Hyun Kwon <hyun.kwon@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

v4l: xilinx: sdirxss: Correct the v4l2_field to V4L2_FIELD_ALTERNATE

Correct the field type to V4L2_FIELD_ALTERNATE instead of
V4L2_FIELD_INTERLACED and halve the height in such cases.

Signed-off-by: Vishal Sagar <vsagar@xilinx.com>
Reviewed-by: Hyun Kwon <hyun.kwon@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

bindings: display: xlnx: Fixing device tree documentation

Adding back dma-names.

Signed-off-by: Saurabh Sengar <saurabhs@xilinx.com>
Reviewed-by: Hyun Kwon <hyun.kwon@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

arm64: zynqmp: config: Enable soft PL V4L drivers

Enable the Demosaic, Gamma, VPSS CSC, VPSS Scaler and
MIPI CSI2 Rx drivers in defconfig.

Signed-off-by: Vishal Sagar <vsagar@xilinx.com>
Reviewed-by: Hyun Kwon <hyun.kwon@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

arm64: zynqmp: config: Enable soft IP DRM drivers

This enables VPSS scaler and color space converter drivers in defconfig.

Signed-off-by: Venkateshwar Rao G <vgannava@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

fpga: region: Add reset support to the fpga region

Many of the fpga regions have a reset that has to be
asserted after the bit file programming. Add support
for the same in case there is no reset phandle passed
no action is taken so it is backward compatible.

Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

drm: xlnx: zynqmp: Disable a plane when the fb format changes

The drm core doesn't explicitly disable a plane when format changes.
So add a check in the plane update functions if the new framebuffer
format has changed, and disable the plane for the format change.

Signed-off-by: Hyun Kwon <hyun.kwon@xilinx.com>
Tested-by: Kuldeep Dave <kuldeepd@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

arm64: zynqmp: Add support for zc1275 revB

This patch enables support zc1275 revB board. It has
SD added compared to revA. The same configuration will
work for RevC boards aswell.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>

arm64: zynqmp: Disable WP on zcu111

On this board there is SD slot without WP connected.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>

serial: xuartps: Fix suspend functionality

The driver's suspend/resume functions were buggy.
If UART node contains any child node in the DT and
the child is established a communication path with
the parent UART. The relevant /dev/ttyPS* node will
be not available for other operations.
If the driver is trying to do any operations like
suspend/resume without checking the tty->dev status
it leads to the kernel crash/hang.

This patch fix this issue by call the device_may_wake()
with the generic parameter of type struct device.
in the uart suspend and resume paths.

It also fixes a race condition in the uart suspend
path(i.e uart_suspend_port() should be called at the
end of cdns_uart_suspend API this path updates the same)

Signed-off-by: Nava kishore Manne <navam@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

drm: xlnx: drv: Shutdown the drm device properly

If a drm device is released immediately in shutdown callback by calling
drm_put_device(), it gives a warnning as below because there are some
resources, drm gem objects, that are still used by fbdev emulation and
attached to the drm device.

> reboot

or

> shutdown -h now

...
[   40.731016] [<ffffff800850adc0>] drm_gem_destroy+0x18/0x30
[   40.736485] [<ffffff800850d690>] drm_dev_fini+0x28/0x90
[   40.741693] [<ffffff800850d764>] drm_dev_unref+0x6c/0x78
[   40.746988] [<ffffff800850d7ac>] drm_put_dev+0x3c/0x70
[   40.752111] [<ffffff80085379b4>] xlnx_shutdown+0x14/0x20
[   40.757407] [<ffffff8008547b2c>] device_shutdown+0x114/0x1f0
[   40.763050] [<ffffff80080ba464>] kernel_restart_prepare+0x34/0x40
[   40.769125] [<ffffff80080ba544>] kernel_restart+0x14/0x78
[   40.774507] [<ffffff80080ba7e4>] SyS_reboot+0xbc/0x1e8
[   40.779627] Exception stack(0xffffff8013b13ec0 to 0xffffff8013b14000)
...

This fixes the warning by shutting down the drm device in complete
sequence.

Signed-off-by: Hyun Kwon <hyun.kwon@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

soc: xilinx: vcu: Provided API to get number of cores

Number of cores related information is provided
through the xvcu_get_num_cores API.

Signed-off-by: Dhaval Shah <dshah@xilinx.com>
Reviewed-by: Varunkumar Allagadapa <varunkumar.allagadapa@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

xilinx: v4l2: dma: Bug fix in single plane support

This patch fixes bugs in single plane handling.
 a. Passing v4l2 pixel format to framebuffer driver
 b. Making dst_icg is zero, though it does not matter
    in case of single plane formats
 c. Correcting bytes per line for single plane 10 bit
    formats

Signed-off-by: Satish Kumar Nagireddy <satishna@xilinx.com>
Reviewed-by: Hyun Kwon <hyun.kwon@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

misc: xilinx-sdfec: Setting FEC_CODE change

Setting of the FEC_Code (LDPC/Turbo) is decided at using the device tree
only (at design time only), remove the setting of the value in the function
xsdfec_set_turbo and xsdfec_add_ldpc to function xsdfec_parse_of to ensure
that this is OK.

Signed-off-by: Derek Kiernan <Derek.Kiernan@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

misc: xilinx-sdfec: Correct invalid order check

Correct the value used when checking order value in the function
xsdfec_start.

Signed-off-by: Derek Kiernan <Derek.Kiernan@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

misc: xilinx-sdfec: Use dev_dbg in xsdfec_regread

To be consistent with xsdfec_regwrite function.

Signed-off-by: Derek Kiernan <Derek.Kiernan@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

misc: xilinx-sdfec: Memory leak fix

In function xsdfec_add_ldpc and xsdfec_get_ldpc_code_params all failures
after successfully allocating "ldpc/ldpc_params" memory should free the
allocated memory before returning from the function.

Signed-off-by: Derek Kiernan <Derek.Kiernan@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

misc: xilinx-sdfec: Change struct for GET_STATUS IOCTL

Removes configuration and error stats information from the status.

Signed-off-by: Derek Kiernan <Derek.Kiernan@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

misc: xilinx-sdfec: Add IOCTL XSDFEC_IS_ACTIVE

Gives the user the ability to determine if the SDFEC is currently
progressing a block of data.

Signed-off-by: Derek Kiernan <Derek.Kiernan@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

misc: xilinx-sdfec: Add BYPASS IOCTLs

To allow user to the bypass the SDFEC block, where output data matches the
input data but the SDFEC performs the same operation(number of cycles).

Signed-off-by: Derek Kiernan <Derek.Kiernan@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

misc: xilinx-sdfec: Fix open_count decrement when already open

In function xsdfec_dev_open if the atomic_dec_and_test detects that driver
is already opened a increment is required. This ensures the driver
instance can the reopened after it is released by the user.

Signed-off-by: Derek Kiernan <Derek.Kiernan@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

misc: xilinx-sdfec: Remove hardcoded Order setting

Occurs in function xsdfec_start.

Signed-off-by: Derek Kiernan <Derek.Kiernan@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

misc: xilinx-sdfec: Add IOCTL XSDFEC_SET_ORDER

Gives user ability to set the order, i.e. if data blocks sequence can
change from input to output.

Signed-off-by: Derek Kiernan <Derek.Kiernan@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

misc: xilinx-sdfec: Verify IOCTL arguments in every IOCTL

Previously the function xsdfec_dev_ioctl always checks if the ioctl
argument is not NULL.

Signed-off-by: Derek Kiernan <Derek.Kiernan@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

arm64: zynqmp: Set Dual Role Device Mode by default

This patch enables the dwc3 DRD mode by default. Doing so, will
make the same Image to be used for both Host & Device modes
based on the dr_mode dts parameter.

Signed-off-by: Anurag Kumar Vulisha <anuragku@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

drm: xlnx: zynqmp_dp: Use the correct number of lanes

The number of lanes is configurable, thus the dynamically configured
value should be used instead of hard-coded max number of lanes. Use
the number of assigned lanes correctly.

While at it, don't print an error for phy probe deferral.

Signed-off-by: Hyun Kwon <hyun.kwon@xilinx.com>
Tested-by: Parth Gajjar <parthg@xilinx.com>
Reviewed-by: Saurabh Sengar <saurabhs@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

v4l: xilinx: dma: Return from mplane handling for enum formats

In current driver implemenataion, it is always falling back to
single plane handling after mplane handling. This patch ensures
that mplane handling return gracefully.

Signed-off-by: Satish Kumar Nagireddy <satishna@xilinx.com>
Reviewed-by: Hyun Kwon <hyun.kwon@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

dt: bindings: display: xlnx: Updated gpio reset entry

This patch updates reset gpio entry arguments.

Signed-off-by: Venkateshwar Rao G <vgannava@xilinx.com>
Reviewed-by: Hyun Kwon <hyun.kwon@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

drm: xlnx: csc: Adding vpss-csc reset through gpio

The color space converter reset is controlled by gpio.

Signed-off-by: Venkateshwar Rao G <vgannava@xilinx.com>
Reviewed-by: Hyun Kwon <hyun.kwon@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

dt: bindings: display: xlnx: Adding gpio reset entry

This patch adds the gpio reset entry for vpss color space converter.
Moved to bindings/display/xlnx folder.

Signed-off-by: Venkateshwar Rao G <vgannava@xilinx.com>
Reviewed-by: Hyun Kwon <hyun.kwon@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

tty: xilinx_uartps: Enable automatic flow control

Enable automatic flow control which should ensure that there is no
mainteinance in connection for zcu100 BT case.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Nava kishore Manne <navam@xilinx.com>

irqchip: xilinx: Clean up error paths

This patch cleans error paths to ensure that
irqc->base is unmapped and intc_dev is being
freed properly.

Signed-off-by: Mubin Sayyed <mubinusm@xilinx.com>
Reviewed-by: Radhey Shyam Pandey <radheys@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

misc: xilinx-sdfec: Add IOCTL to get LDPC Params

Adding IOTCL XSDFEC_GET_LDPC_CODE_PARAMS to allow user verify LDPC
code params.

Signed-off-by: Derek Kiernan <Derek.Kiernan@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

misc: xilinx-sdfec: Add IOCTL to get Turbo Params

Adding IOCTL XSDFEC_GET_TURBO to allow user verify entries turbo param
values.

Signed-off-by: Derek Kiernan <Derek.Kiernan@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

soc: zynqmp: Fix PMU version comparison

Fix comparison of actual PMUFW version with expected version.

Signed-off-by: Rajan Vaja <rajanv@xilinx.com>
Acked-by: Jolly Shah <jollys@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

arm64: zynqmp: dt: Move zynqmp_dpsub under amba

The DP device node should be under amba. Currently, it's under root,
and this patch moves the node under amba.

Signed-off-by: Hyun Kwon <hyun.kwon@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

drm: xlnx: scaler: Updating vpss-scaler reset logic

This patch updates the reset through gpio logic

Signed-off-by: Venkateshwar Rao G <vgannava@xilinx.com>
Reviewed-by: Hyun Kwon <hyun.kwon@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

Bluetooth: hci_ll: Extend timeout between start and communication

Extend timeout between bt enable and communication with chip.
Flow control is automatic and driver is responding that device is ready
to accept messages but it doesn't need to be truth. Wait more time to
ensure that communication cat start.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Series-prefix: LINUX
Cover-letter:
zcu100 BT fixes
Hi,

I have cherry-picked mainline patches to make sure that we are using the
latest hci_ll code with fixes.

CR-993696

Thanks,
Michal
END

arm64: zynqmp: Enable serdev devices for zcu100 BT chip

Enable HCIuart and serdev.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>

arm64: zynqmp: Use serdev for zcu100 BT

Mainline started to use serdev interface for uart attached devices.
Change description to reflect it.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>

Bluetooth: hci_ll: Add optional nvmem BD address source

This adds an optional nvmem consumer to get a BD address from an external
source. The BD address is then set in the Bluetooth chip after the
firmware has been loaded.

This has been tested working with a TI CC2560A chip (in a LEGO MINDSTORMS
EV3).

Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Bluetooth: hci_ll: Add endianness conversion when setting baudrate

This adds an endianness conversion when setting the baudrate using a
vendor-specific command. Otherwise, bad things might happen on a big-
endian system.

Suggested-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Bluetooth: hci_ll: remove \n from kernel messages

The bt_* printk macros include a \n already, so we don't need extra ones
here.

Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Bluetooth: mark expected switch fall-throughs

In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.

In this particular case, notice that I replaced the
"deliberate fall-through..." comment with a "fall through"
comment, which is what GCC is expecting to find.

Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Bluetooth: hci_ll: add support for setting public address

This adds support for setting the public address on Texas Instruments
Bluetooth chips using a vendor-specific command.

This has been tested on a CC2560A chip. The TI wiki also indicates that
this command should work on TI WL17xx/WL18xx Bluetooth chips.

During review, there was some question as to the correctness of the byte
swapping since TI's documentation is not clear on this matter. This can
be tested with the btmgmt utility from bluez. The adapter must be powered
off to change the address. If the baswap() is omitted, address is reversed.

In case there is a issue in the future, here is the output of btmon during
the command `btmgmt public-addr 00:11:22:33:44:55`:

Bluetooth monitor ver 5.43
= Note: Linux version 4.15.0-rc2-08561-gcb132a1-dirty (armv5tejl)      0.707043
= Note: Bluetooth subsystem version 2.22                               0.707091
= New Index: 00:17:E7:BD:1C:8E (Primary,UART,hci0)              [hci0] 0.707106
@ MGMT Open: btmgmt (privileged) version 1.14                 {0x0002} 0.707124
@ MGMT Open: bluetoothd (privileged) version 1.14             {0x0001} 0.707137
@ MGMT Open: btmon (privileged) version 1.14                  {0x0003} 0.707540
@ MGMT Command: Set Public Address (0x0039) plen 6    {0x0002} [hci0] 11.167991
        Address: 00:11:22:33:44:55 (CIMSYS Inc)
@ MGMT Event: Command Complete (0x0001) plen 7        {0x0002} [hci0] 11.175681
      Set Public Address (0x0039) plen 4
        Status: Success (0x00)
        Missing options: 0x00000000
@ MGMT Event: Index Removed (0x0005) plen 0           {0x0003} [hci0] 11.175757
@ MGMT Event: Index Removed (0x0005) plen 0           {0x0002} [hci0] 11.175757
@ MGMT Event: Index Removed (0x0005) plen 0           {0x0001} [hci0] 11.175757
= Open Index: 00:17:E7:BD:1C:8E                                [hci0] 11.176807
< HCI Command: Vendor (0x3f|0x0006) plen 6                     [hci0] 11.176975
        00 11 22 33 44 55                                .."3DU
> HCI Event: Command Complete (0x0e) plen 4                    [hci0] 11.188260
      Vendor (0x3f|0x0006) ncmd 1
        Status: Success (0x00)
...
< HCI Command: Read Local Version Info.. (0x04|0x0001) plen 0  [hci0] 11.189859
> HCI Event: Command Complete (0x0e) plen 12                   [hci0] 11.190732
      Read Local Version Information (0x04|0x0001) ncmd 1
        Status: Success (0x00)
        HCI version: Bluetooth 2.1 (0x04) - Revision 0 (0x0000)
        LMP version: Bluetooth 2.1 (0x04) - Subversion 6431 (0x191f)
        Manufacturer: Texas Instruments Inc. (13)
< HCI Command: Read BD ADDR (0x04|0x0009) plen 0               [hci0] 11.191027
> HCI Event: Command Complete (0x0e) plen 10                   [hci0] 11.192101
      Read BD ADDR (0x04|0x0009) ncmd 1
        Status: Success (0x00)
        Address: 00:11:22:33:44:55 (CIMSYS Inc)
...

Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Bluetooth: hci_ll: add constant for vendor-specific command

This adds a #define for the vendor-specific HCI command to set the
baudrate instead of using the bare 0xff36 multiple times.

Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Bluetooth: serdev: hci_ll: Wait for CTS instead of using msleep

When a TI Bluetooth chip is reset, it takes about 100ms for the RTS line of
the chip to deassert. For my use case with a TI CC2560A chip, this delay
was not long enough and caused the local UART to never transmit at all (TI
AM1808 SoC UART2).

We can wait for the CTS signal using serdev_device_wait_for_cts() instead
of trying to guess using msleep().

Also changed the comment to be more informative while we are touching this
code.

Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Revert "of: overlay: add overlay symbols to live device tree"

This reverts commit d1651b03c2df75db8eda3fbcd3a07adb337ee8b0.

This commit must be reverted, else loading overlays
from the configfs interface will be fails with the
following errors:
OF: changeset: add_property failed @/__symbols__/...
OF: Error applying changeset (-17)

Signed-off-by: Nava kishore Manne <navam@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

misc: xilinx-sdfec: Rename XSDFEC_ADD_LDPC IOCTL

To be more explicit.

Signed-off-by: Derek Kiernan <Derek.Kiernan@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

misc: xilinx-sdfec: Rename xsd_ldpc

To be more explicit.

Signed-off-by: Derek Kiernan <Derek.Kiernan@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

misc: xilinx-sdfec: Remove lat_ctrl from xsd_ldpc

lat_ctrl is not required with the removal of the Latency Control field
from Reg2.

Signed-off-by: Derek Kiernan <Derek.Kiernan@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

misc: xilinx-sdfec: Remove XSDFEC_REG2_LAT_CTRL_*

Remove any references to Latency Control field of Reg2 register, the
register has been removed from the SDFEC Block.

Signed-off-by: Derek Kiernan <Derek.Kiernan@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

microblaze: Enable SPARSE_IRQ

Enabling SPARSE_IRQ to use dynamically allocated
irq descriptors.

Signed-off-by: Mubin Sayyed <mubinusm@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

irqchip: xilinx: Add support for multiple instances

This patch adds support for multiple instances of
xilinx interrupt controller. Below configurations are
supported by driver,

- peripheral->xilinx-intc->xilinx-intc->gic
- peripheral->xilinx-intc->xilinx-intc

Signed-off-by: Anirudha Sarangi <anirudh@xilinx.com>
Signed-off-by: Mubin Sayyed <mubinusm@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

arm64: zynqmp: dt: Add new ZynqMP DP changes

This removes old dt contents from all dts files for ZynqMP DisplayPort
and updates all with new bindings. Please note, some of these changes
are only build-tested.

Signed-off-by: Hyun Kwon <hyun.kwon@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

arm64: zynqmp: config: Enable soft IP DRM drivers

This enables DSI, SDI, Mixer, and the PL display drivers in defconfig.

Signed-off-by: Hyun Kwon <hyun.kwon@xilinx.com>
Acked-by: Saurabh Sengar <saurabhs@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

arm64: zynqmp: config: Enable new Xilinx drm configs

Enable the new DRM configs. Keep the old ones for now,
and the DT can be used to selct one.

Signed-off-by: Hyun Kwon <hyun.kwon@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

drm: xilinx: plane: Use drm_format_plane_width_bytes

This will calculate the number of bytes correctly for macropixel
formats.

Signed-off-by: Hyun Kwon <hyun.kwon@xilinx.com>
Reviewed-by: Satish Kumar Nagireddy <satishna@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

drm: xilinx: dp_sub: Add 10 bit YUV formats

This patch add support for 10 bit YUV formats (XV15 and XV20)
in ZynqMP dp driver.

Signed-off-by: Satish Kumar Nagireddy <satishna@xilinx.com>
Signed-off-by: Hyun Kwon <hyun.kwon@xilinx.com>
Reviewed-by: Satish Kumar Nagireddy <satishna@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

uapi: drm: Add AVUY fourcc

AVUY is a 32bit single plane YUV format, with 2 bit alpha,
and in order of A:Cr:Cb:Y in little endian.

Signed-off-by: Jeffrey Mouroux <jmouroux@xilinx.com>
Signed-off-by: Hyun Kwon <hyun.kwon@xilinx.com>
Reviewed-by: Satish Kumar Nagireddy <satishna@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

device-tree: serdes: Remove unused lpd register address mapping

This patch removes the unused lpd register address mapping from
serdes dts node.

Signed-off-by: Anurag Kumar Vulisha <anuragku@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

phy: zynqmp: Use eemi framework for performing ULPI reset sequence

This patch modifies the phy-zynqmp.c driver to use eemi framework
for performing ULPI reset sequence.

Signed-off-by: Anurag Kumar Vulisha <anuragku@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

zynqmp: firmware: Add IOCTL enum for performing ULPI reset

This patch adds IOCTL_ULPI_RESET IOCTL enum value that is
passed to eemi framework for performing ULPI reset

Signed-off-by: Anurag Kumar Vulisha <anuragku@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

misc: xilinx-sdfec: DRIVER_VERSION Update

Updated DRIVER_VERSION to "0.3" for 2018.1 SD-FEC drivers updates.

Signed-off-by: Derek Kiernan <Derek.Kiernan@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

misc: xilinx-sdfec: Max # Instances display update

Display 7 as the MAX number of instances. In function xsdfec_probe during
check of "xsdfec_ndevs" to ensure Human Readable.

Signed-off-by: Derek Kiernan <Derek.Kiernan@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

misc: xilinx-sdfec: Fix enum xsdfec_order values

Add XSDFEC_ prefix to enum xsdfec_order values. To be consistent.

Signed-off-by: Derek Kiernan <Derek.Kiernan@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

misc: xilinx-sdfec: Added GET_CONFIG IOCTL

To allow validation of Core/Driver configuration.

Signed-off-by: Derek Kiernan <Derek.Kiernan@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

clk: clk-fixed-factor: Use new macro CLK_OF_DECLARE_DRIVER

Fixed factor clock has two initialization at of_clk_init()
time and also during platform driver probe. So declare the
fixed factor clock with CLK_OF_DECLARE_DRIVER instead of
CLK_OF_DECLARE.

See below commit for reference:
"clk: sunxi: apb0: Use new macro CLK_OF_DECLARE_DRIVER"
(sha1: 915128b621a05c63fa58ca9e4cbdf394bbe592f3)

Signed-off-by: Rajan Vaja <rajanv@xilinx.com>
Suggested-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

uvcvideo: Prevent new URBs being processed at stream stop

With asynchronous handling of the URBs from the USB Complete handler, we
get a continual stream of packets being received while we are attempting
to shutdown the stream.

Packets that have already been received and processed are on a
work-queue, but during stream shutdown the URBs that those packets
belong to are killed and free'd.

To prevent this race from causing invalid memory accesses, prevent new
URBs from being processed when uvc_stop_streaming() is called by
introducing a new flag "UVC_QUEUE_STOPPING" into the queue, and checking
this when processing the URB to be queued.

With this, we can flush the work queue, and commence a normal pipe
shutdown. Work tasks that are already queued are processed, but the URBs
are prevented from being re-submitted to the USB stack.

Signed-off-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Signed-off-by: Christian Kohn <christian.kohn@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

staging: apf: Add synchronization for DMA-BUF add/remove

DMA-BUF attachment in the APF driver lacked appropriate locking
guarantees. This patch adds those protections to allow for
concurrent attach/detach calls.

Signed-off-by: Michael Gill <gill@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

net: macb: Cleanup empty lines

Remove two extra empty lines.

Signed-off-by: Harini Katakam <harinik@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

networking: introduce and use skb_put_data()

A common pattern with skb_put() is to just want to memcpy()
some data into the new space, introduce skb_put_data() for
this.

An spatch similar to the one for skb_put_zero() converts many
of the places using it:

    @@
    identifier p, p2;
    expression len, skb, data;
    type t, t2;
    @@
    (
    -p = skb_put(skb, len);
    +p = skb_put_data(skb, data, len);
    |
    -p = (t)skb_put(skb, len);
    +p = skb_put_data(skb, data, len);
    )
    (
    p2 = (t2)p;
    -memcpy(p2, data, len);
    |
    -memcpy(p, data, len);
    )

    @@
    type t, t2;
    identifier p, p2;
    expression skb, data;
    @@
    t *p;
    ...
    (
    -p = skb_put(skb, sizeof(t));
    +p = skb_put_data(skb, data, sizeof(t));
    |
    -p = (t *)skb_put(skb, sizeof(t));
    +p = skb_put_data(skb, data, sizeof(t));
    )
    (
    p2 = (t2)p;
    -memcpy(p2, data, sizeof(*p));
    |
    -memcpy(p, data, sizeof(*p));
    )

    @@
    expression skb, len, data;
    @@
    -memcpy(skb_put(skb, len), data, len);
    +skb_put_data(skb, data, len);

(again, manually post-processed to retain some comments)a

Picked change for macb driver only.

Reviewed-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Harini Katakam <harinik@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

lib/vsprintf.c: remove %Z support

Now that %z is standartised in C99 there is no reason to support %Z.
Unlike %L it doesn't even make format strings smaller.

Use BUILD_BUG_ON in a couple ATM drivers.

In case anyone didn't notice lib/vsprintf.o is about half of SLUB which
is in my opinion is quite an achievement.  Hopefully this patch inspires
someone else to trim vsprintf.c more.

Picked up change for macb driver only.

Link: http://lkml.kernel.org/r/20170103230126.GA30170@avx2
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Harini Katakam <harinik@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>