blitting. This is used by drivers that don't provide their own
(accelerated) version and the framebuffer is in system RAM.
+menuconfig FB_FOREIGN_ENDIAN
+ bool "Framebuffer foreign endianness support"
+ depends on FB
+ ---help---
+ This menu will let you enable support for the framebuffers with
+ non-native endianness (e.g. Little-Endian framebuffer on a
+ Big-Endian machine). Most probably you don't have such hardware,
+ so it's safe to say "n" here.
+
+choice
+ prompt "Choice endianness support"
+ depends on FB_FOREIGN_ENDIAN
+
+config FB_BOTH_ENDIAN
+ bool "Support for Big- and Little-Endian framebuffers"
+
+config FB_BIG_ENDIAN
+ bool "Support for Big-Endian framebuffers only"
+
+config FB_LITTLE_ENDIAN
+ bool "Support for Little-Endian framebuffers only"
+
+endchoice
+
config FB_SYS_FOPS
tristate
depends on FB
config FB_DEFERRED_IO
bool
depends on FB
- default y
+
+config FB_METRONOME
+ tristate
+ depends on FB
+ depends on FB_DEFERRED_IO
+
+config FB_HECUBA
+ tristate
+ depends on FB
+ depends on FB_DEFERRED_IO
config FB_SVGALIB
tristate
config FB_BF54X_LQ043
tristate "SHARP LQ043 TFT LCD (BF548 EZKIT)"
- depends on FB && (BF54x)
+ depends on FB && (BF54x) && !BF542
select FB_CFB_FILLRECT
select FB_CFB_COPYAREA
select FB_CFB_IMAGEBLIT
select FB_CFB_IMAGEBLIT
select FB_MACMODES
-# bool ' Apple DAFB display support' CONFIG_FB_DAFB
config FB_HP300
bool
- depends on (FB = y) && HP300
- select FB_CFB_FILLRECT
+ depends on (FB = y) && DIO
select FB_CFB_IMAGEBLIT
default y
help
This is the frame buffer device driver for the Intel-based Macintosh
-config FB_HECUBA
- tristate "Hecuba board support"
+config FB_N411
+ tristate "N411 Apollo/Hecuba devkit support"
depends on FB && X86 && MMU
select FB_SYS_FILLRECT
select FB_SYS_COPYAREA
select FB_SYS_IMAGEBLIT
select FB_SYS_FOPS
select FB_DEFERRED_IO
+ select FB_HECUBA
help
- This enables support for the Hecuba board. This driver was tested
- with an E-Ink 800x600 display and x86 SBCs through a 16 bit GPIO
- interface (8 bit data, 4 bit control). If you anticipate using
- this driver, say Y or M; otherwise say N. You must specify the
- GPIO IO address to be used for setting control and data.
+ This enables support for the Apollo display controller in its
+ Hecuba form using the n411 devkit.
config FB_HGA
tristate "Hercules mono graphics support"
This driver supports the LE80578 (Carillo Ranch) board
config FB_INTEL
- tristate "Intel 830M/845G/852GM/855GM/865G/915G/945G support (EXPERIMENTAL)"
+ tristate "Intel 830M/845G/852GM/855GM/865G/915G/945G/945GM/965G/965GM support (EXPERIMENTAL)"
depends on FB && EXPERIMENTAL && PCI && X86
select AGP
select AGP_INTEL
select FB_CFB_IMAGEBLIT
help
This driver supports the on-board graphics built in to the Intel
- 830M/845G/852GM/855GM/865G/915G/915GM/945G/945GM chipsets.
+ 830M/845G/852GM/855GM/865G/915G/915GM/945G/945GM/965G/965GM chipsets.
Say Y if you have and plan to use such a board.
If you say Y here and want DDC/I2C support you must first say Y to
If unsure, say N.
+config FB_PXA_SMARTPANEL
+ bool "PXA Smartpanel LCD support"
+ default n
+ depends on FB_PXA
+
config FB_PXA_PARAMETERS
bool "PXA LCD command line parameters"
default n
If unsure, say N.
+config FB_FSL_DIU
+ tristate "Freescale DIU framebuffer support"
+ depends on FB && FSL_SOC
+ select FB_CFB_FILLRECT
+ select FB_CFB_COPYAREA
+ select FB_CFB_IMAGEBLIT
+ select PPC_LIB_RHEAP
+ ---help---
+ Framebuffer driver for the Freescale SoC DIU
+
config FB_W100
tristate "W100 frame buffer support"
depends on FB && PXA_SHARPSL
framebuffer. ML300 carries a 640*480 LCD display on the board,
ML403 uses a standard DB15 VGA connector.
-config FB_METRONOME
- tristate "Metronome display controller support"
+config FB_AM200EPD
+ tristate "AM-200 E-Ink EPD devkit support"
depends on FB && ARCH_PXA && MMU
select FB_SYS_FILLRECT
select FB_SYS_COPYAREA
select FB_SYS_IMAGEBLIT
select FB_SYS_FOPS
select FB_DEFERRED_IO
+ select FB_METRONOME
help
- This enables support for the Metronome display controller. Tested
- with an E-Ink 800x600 display and Gumstix Connex through an AMLCD
- interface. Please read <file:Documentation/fb/metronomefb.txt>
- for more information.
+ This enables support for the Metronome display controller used on
+ the E-Ink AM-200 EPD devkit.
config FB_VIRTUAL
tristate "Virtual Frame Buffer support (ONLY FOR TESTING!)"
If unsure, say N.
+config XEN_FBDEV_FRONTEND
+ tristate "Xen virtual frame buffer support"
+ depends on FB && XEN
+ select FB_SYS_FILLRECT
+ select FB_SYS_COPYAREA
+ select FB_SYS_IMAGEBLIT
+ select FB_SYS_FOPS
+ select FB_DEFERRED_IO
+ default y
+ help
+ This driver implements the front-end of the Xen virtual
+ frame buffer driver. It communicates with a back-end
+ in another domain.
+
source "drivers/video/omap/Kconfig"
source "drivers/video/backlight/Kconfig"
projects / zynq / linux.git / blobdiff