config CAN_VCAN
tristate "Virtual Local CAN Interface (vcan)"
- depends on CAN
+ depends on CAN
default N
- ---help---
+ ---help---
Similar to the network loopback devices, vcan offers a
virtual local CAN interface.
This driver can also be built as a module. If so, the module
will be called vcan.
-config CAN_OLD_DRIVERS
- tristate "Prompt for old CAN drivers (e.g. no sysfs support)"
- depends on CAN
- default N
- ---help---
- The old drivers do not support sysfs nor proper platform device
- support. Some of the old drivers might only be configured by
- module commandline options.
-
config CAN_SLCAN
tristate "Serial / USB serial CAN Adaptors (slcan)"
- depends on CAN && EXPERIMENTAL
+ depends on CAN
default N
---help---
CAN driver for several 'low cost' CAN interfaces that are attached
via serial lines or via USB-to-serial adapters using the LAWICEL
ASCII protocol. The driver implements the tty linediscipline N_SLCAN.
- This driver can also be built as a module. If so, the module
- will be called slcan.
+ As only the sending and receiving of CAN frames is implemented, this
+ driver should work with the (serial/USB) CAN hardware from:
+ www.canusb.com / www.can232.com / www.mictronic.com / www.canhack.de
-config CAN_SJA1000
- tristate "Philips SJA1000"
- ---help---
- The SJA1000 is one of the top CAN controllers out there. As it
- has a multiplexed interface it fits directly to 8051
- microcontrollers or into the PC I/O port space. The SJA1000
- is a full CAN controller, with shadow registers for RX and TX.
- It can send and receive any kinds of CAN frames (SFF/EFF/RTR)
- with a single (simple) filter setup.
-
- This driver will use the new device interface.
-
-config CAN_MSCAN
- depends on CAN && (PPC || M68K || M68KNOMMU)
- tristate "Support for a Freescale MSCAN based chips"
- ---help---
- The Motorola Scalable Controller Area Network (MSCAN) definition
- is based on the MSCAN12 definition which is the specific
- implementation of the Motorola Scalable CAN concept targeted for
- the Motorola MC68HC12 Microcontroller Family.
-
-config CAN_MPC52XX
- tristate "Freescale MPC5200 onboard CAN controller"
- depends on CAN_MSCAN && (PPC_MPC52xx || PPC_52xx)
- default LITE5200
- ---help---
- If you say yes here you get support for Freescale MPC5200
- onboard dualCAN controller.
+ Userspace tools to attach the SLCAN line discipline (slcan_attach,
+ slcand) can be found in the can-utils at the SocketCAN SVN, see
+ http://developer.berlios.de/projects/socketcan for details.
- This driver can also be built as a module. If so, the module
- will be called mpc52xx_can.
+ The slcan driver supports up to 10 CAN netdevices by default which
+ can be changed by the 'maxdev=xx' module option. This driver can
+ also be built as a module. If so, the module will be called slcan.
-config CAN_CCAN
+config CAN_OLD_DRIVERS
+ tristate "Prompt for old CAN drivers (e.g. no sysfs support)"
depends on CAN
- tristate "Bosch CCAN driver"
- ---help---
- This is a driver for the Bosch CCAN controller found for example
- on the hynix h7202 chip.
-
-config CAN_H7202
- tristate "Hynix H7202 onboard CAN controller"
- depends on CAN_CCAN
+ default N
---help---
- This is a driver for the hynix h7202 can controller.
-
-config CAN_EMS_PCI
- tristate "EMS CPC-PCI and CPC-PCIe Card"
- depends on PCI && CAN_SJA1000
- help
+ The old drivers do not support sysfs nor proper platform device
+ support. Some of the old drivers might only be configured by
+ module commandline options.
- This driver is for the one or two channel CPC-PCI and CPC-PCIe
- cards from EMS Dr. Thomas Wuensche (http://www.ems-wuensche.de).
+if CAN_OLD_DRIVERS
+source "drivers/net/can/old/Kconfig"
+endif
-config CAN_IXXAT_PCI
- tristate "IXXAT PCI Card"
- depends on PCI && CAN_SJA1000
- help
+config CAN_DEV
+ tristate "Platform CAN drivers with Netlink support"
+ depends on CAN
+ default Y
+ ---help---
+ Enables the common framework for platform CAN drivers with Netlink
+ support. This is the standard library for CAN drivers.
+ If unsure, say Y.
- This driver is for the IXXAT PC-I 04/PCI card (1 or 2 channel)
- from the IXXAT Automation GmbH (http://www.ixxat.de).
+config CAN_DEV_SYSFS
+ bool "Support for sysfs interface (deprecated)"
+ depends on CAN_DEV && SYSFS
+ default N
+ ---help---
+ Adds support for the legacy sysfs interface to configure CAN
+ devices. If possible, please use the new netlink interface
+ instead.
+ If unsure, say N.
+
+config CAN_CALC_BITTIMING
+ bool "CAN bit-timing calculation"
+ depends on CAN_DEV
+ default Y
+ ---help---
+ If enabled, CAN bit-timing parameters will be calculated for the
+ bit-rate specified via Netlink argument "bitrate" when the device
+ get started. This works fine for the most common CAN controllers
+ with standard bit-rates but may fail for exotic bit-rates or CAN
+ source clock frequencies. Disabling saves some space, but then the
+ bit-timing parameters must be specified directly using the Netlink
+ arguments "tq", "prop_seg", "phase_seg1", "phase_seg2" and "sjw".
+ If unsure, say Y.
+
+config CAN_ESD_PCI331
+ tristate "ESD CAN 331 Cards"
+ depends on PCI && CAN_DEV
+ ---help---
+ This driver supports the PCI/331, CPCI/331 and PMC/331 CAN cards
+ from the esd system design gmbh (http://www.esd.eu).
-config CAN_PEAK_PCI
- tristate "PEAK PCAN PCI Card"
- depends on PCI && CAN_SJA1000
- help
+config CAN_SOFTING
+ tristate "Softing Gmbh CAN generic support"
+ depends on CAN_DEV
+ ---help---
+ generic softing CAN cards
+ Sofing CAN cards come with 1 or 2 physical busses.
+ The API of the card does not allow fine control per bus, but
+ controls the 2 busses on the card together.
+ As such, some actions (start/stop/busoff recovery) on 1 bus
+ must bring down the other bus too temporarily.
+ You have been warned.
+ This driver is written on safe on 64bit, but not on big endian.
+
+config CAN_SOFTING_CS
+ tristate "Softing CAN pcmcia cards"
+ depends on CAN_SOFTING && PCMCIA
+ ---help---
+ Support for PCMCIA cards from Softing Gmbh & some cards
+ from Vector Gmbh.
+ You need firmware for these, which you can get at
+ http://developer.berlios.de/projects/socketcan/
+ This version of the driver is written against
+ firmware version 4.6
+
+config CAN_AT91
+ tristate "Atmel AT91 onchip CAN controller"
+ depends on CAN_DEV && ARCH_AT91SAM9263
+ default N
+ ---help---
+ This is a driver for the SoC CAN controller in Atmel's AT91SAM9263.
- This driver is for the PCAN PCI, the PC-PCI CAN plug-in card (1 or
- 2 channel) from PEAK Systems (http://www.peak-system.com).
+config CAN_MCP251X
+ tristate "Microchip MCP251x SPI CAN controllers"
+ depends on CAN_DEV && SPI
+ ---help---
+ Driver for the Microchip MCP251x SPI CAN controllers.
-config CAN_PCM027
- depends on CAN_SJA1000 && MACH_PCM027
- tristate "Phytec pcm027 can driver (SJA1000)"
- help
- This driver adds support for the SJA1000 chip on the PCM027 board
- from Phytec (http://www.phytec.de).
+source "drivers/net/can/cc770/Kconfig"
-config CAN_KVASER_PCI
- tristate "Kvaser PCIcanx and Kvaser PCIcan PCI Cards"
- depends on PCI && CAN_SJA1000
- help
+source "drivers/net/can/mscan/Kconfig"
- This driver is for the the PCIcanx and PCIcan cards (1, 2 or
- 4 channel) from Kvaser (http://www.kvaser.com).
+source "drivers/net/can/sja1000/Kconfig"
-source "drivers/net/can/old/Kconfig"
+source "drivers/net/can/usb/Kconfig"
config CAN_DEBUG_DEVICES
bool "CAN devices debugging messages"