Kyoungil Kim [Mon, 22 Oct 2012 11:01:00 +0000 (20:01 +0900)]
mmc: sdio: Use multiple scatter/gather list
Before this patch, we always used only single sg entry for SDIO transfer.
This patch switches to using multiple sg entries. In the case of dwmci,
it supports only up to 4KB size per single sg entry. So if we want to
transfer more than 4KB, we should send more than 1 command.
When we tested before applying this patch, it took around 335 us for
5K(5120) bytes transfer with dwmci controller. After applying this patch,
it takes 242 us for 5K bytes. So this patch makes around 38% performance
improvement for 5K bytes transfer. If the transfer size is bigger, then
the performance improvement ratio will be increased.
Signed-off-by: Kyoungil Kim <ki0351.kim@samsung.com> Signed-off-by: Chris Ball <cjb@laptop.org>
Trey Ramsay [Fri, 16 Nov 2012 15:31:41 +0000 (09:31 -0600)]
mmc: core: Fix some driver hangs when dealing with broken devices
There are infinite loops in the mmc code that can be caused by bad
hardware. The code will loop forever if the device never comes back
from program mode, R1_STATE_PRG, and it is not ready for data,
R1_READY_FOR_DATA.
A long timeout is added to prevent the code from looping forever.
The timeout will occur if the device never comes back from program
state or the device never becomes ready for data.
It's not clear whether the timeout will do more than log a pr_err()
and then start a fresh hang all over again. We may need to extend
this patch later to perform some kind of reset of the device (is
that possible?) or rejection of new I/O to the device.
Signed-off-by: Trey Ramsay <tramsay@linux.vnet.ibm.com> Signed-off-by: Chris Ball <cjb@laptop.org>
Arnd Bergmann [Thu, 8 Nov 2012 14:26:11 +0000 (14:26 +0000)]
mmc: dw_mmc: fix more const pointer warnings
The patch "dw_mmc: fix multiple drv_data NULL dereferences" has
unfortunately clashed with my "mmc: dw_mmc: constify dw_mci_idmac_ops
in exynos back-end" patch, causing new warnings to appear.
This should hopefully fix the issue for good.
Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Chris Ball <cjb@laptop.org>
Balaji T K [Thu, 25 Oct 2012 15:58:35 +0000 (21:28 +0530)]
mmc: omap_hsmmc: remove warning message for debounce clock
MMC debounce clock is applicable only for omap2430, warning message gets
printed when enable fails for debounce clock. Remove the get debounce clock
failure message as it is noisy for other platforms.
Signed-off-by: Balaji T K <balajitk@ti.com> Reported-by: Russell King <rmk+kernel@arm.linux.org.uk> Acked-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Chris Ball <cjb@laptop.org>
Javier Martin [Tue, 30 Oct 2012 15:54:07 +0000 (16:54 +0100)]
mmc: mxcmmc: fix SD cards not being detected sometimes.
When a SD card is initialized some data transfers of 64 and 8 bytes
are issued. It seems the DMA has some problems dealing with these kind
of "short" transfers, leading sometimes to the SD card not being detected.
In order to solve this problem, do not use DMA for transfer sizes lower
than the sector size.
Signed-off-by: Javier Martin <javier.martin@vista-silicon.com> Acked-by: Sascha Hauer <s.hauer@pengutronix.de> Signed-off-by: Chris Ball <cjb@laptop.org>
Andy Shevchenko [Wed, 3 Oct 2012 13:26:37 +0000 (16:26 +0300)]
mmc: dw_mmc: use helper macro module_platform_driver()
Since v3.2 we have nice macro to define the platform driver's init and exit
calls. This patch simplifies the dw_mmc platform driver by using that macro.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Reviewed-by: Girish K S <girish.shivanajappa@linaro.org> Acked-by: Will Newton <will.newton@imgtec.com> Signed-off-by: Chris Ball <cjb@laptop.org>
Andy Shevchenko [Wed, 3 Oct 2012 13:45:23 +0000 (16:45 +0300)]
mmc: dw_mmc: use __devexit_p macro for .remove()
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Reviewed-by: Girish K S <girish.shivananjappa@linaro.org> Acked-by: Will Newton <will.newton@imgtec.com> Signed-off-by: Chris Ball <cjb@laptop.org>
mmc: queue: amend buffer swap for non-blocking transfer
In case both 'req' and 'mq->mqrq_prev->req' are null, there is no request
to be processed. That means there is no need to switch buffer.
Switching buffer is required only after finishing 'issue_fn'.
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com> Reviewed-by: Per Forlin <per.forlin@stericsson.com> Tested-by: Johan Rudholm <johan.rudholm@stericsson.com> Signed-off-by: Chris Ball <cjb@laptop.org>
mmc: sh-mmcif: avoid oops on spurious interrupts (second try)
On some systems, e.g., kzm9g, MMCIF interfaces can produce spurious
interrupts without any active request. To prevent the Oops, that results
in such cases, don't dereference the mmc request pointer until we make
sure, that we are indeed processing such a request.
Kevin Liu [Sat, 17 Nov 2012 22:55:51 +0000 (17:55 -0500)]
mmc: sdhci: Balance vmmc regulator_enable(), and always enable vqmmc
The vmmc regulator enable in sdhci_add_host is NOT necessary since
it can be enabled during mmc_power_up by function mmc_regulator_set_ocr.
And this extra enable will make regulator_enable/regulator_disable
unbalanced. Consequently, vmmc can't be disabled during mmc_power_off.
Also, if the vqmmc regulator exists, it should be enabled regardless it
support 1.8v or not.
Signed-off-by: Kevin Liu <kliu5@marvell.com> Signed-off-by: Philip Rakity <prakity@marvell.com> Signed-off-by: Chris Ball <cjb@laptop.org>
Heiko Stübner [Sun, 18 Nov 2012 18:50:05 +0000 (19:50 +0100)]
mmc: sdhci-s3c: fix missing clock for gpio card-detect
2abeb5c5ded2 ("Add clk_(enable/disable) in runtime suspend/resume")
added the capability to stop the clocks when the device is runtime
suspended, but forgot to handle the case of the card-detect using
an external gpio.
Therefore in the case that runtime-pm is enabled, start the io-clock
when a card is inserted and stop it again once it is removed.
Signed-off-by: Heiko Stuebner <heiko@sntech.de> Signed-off-by: Chris Ball <cjb@laptop.org>
Linus Torvalds [Thu, 6 Dec 2012 16:42:13 +0000 (08:42 -0800)]
Merge branch 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus
Pull MIPS fixes from Ralf Baechle:
"These are the fixes for the N32 syscall bugs found by Al, an
extraneous break that broke detection for R3000 and R3081 processors,
an endless loop processing signals for kernel task (x86 received the
same fix a while ago) and a fix for transparent huge page which took
ages to track down because it was so hard to come up with a workable
test case."
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
MIPS: Fix endless loop when processing signals for kernel tasks
MIPS: R3000/R3081: Fix CPU detection.
MIPS: N32: Fix signalfd4 syscall entry point
MIPS: N32: Fix preadv(2) and pwritev(2) entry points.
MIPS: Avoid mcheck by flushing page range in huge_ptep_set_access_flags()
Linus Torvalds [Thu, 6 Dec 2012 16:39:57 +0000 (08:39 -0800)]
Merge branch 'more-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux
Pull build fix from Rusty Russell:
"Tim Gardner <tim.gardner@canonical.com> writes:
> It is $(obj)/oid_registry.o that is dependent on $(obj)/oid_registry_data.c.
> The object file cannot be built until $(obj)/oid_registry_data.c has been
> generated.
>
> A periodic and hard to reproduce parallel build failure is due to
> this incorrect lib/Makefile dependency. The compile error is completely
> disingenuous.
>
> GEN lib/oid_registry_data.c
> Compiling 49 OIDs
> CC lib/oid_registry.o
> gcc: error: lib/oid_registry.c: No such file or directory
> gcc: fatal error: no input files
> compilation terminated.
> make[3]: *** [lib/oid_registry.o] Error 4
I can't reproduce it either. It's completely weird; nothing ever
removes lib/oid_registry.c, so either gcc is giving the wrong message
or it's a weird fs with a very odd race.
But your version is definitely more correct than the previous one,
so..."
* 'more-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux:
lib/Makefile: Fix oid_registry build dependency
Linus Torvalds [Thu, 6 Dec 2012 16:29:08 +0000 (08:29 -0800)]
Merge branch 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux
Pull module signing fixes from Rusty Russell:
"David gave me these a month ago, during my git workflow churn :("
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux:
ASN.1: Fix an indefinite length skip error
MODSIGN: Don't use enum-type bitfields in module signature info block
Grant Likely [Thu, 6 Dec 2012 09:53:13 +0000 (09:53 +0000)]
devicetree/bindings: Move gpio-leds binding into leds directory
Merely reorganizing documentation. No functional changes. It makes more
sense for the gpio-leds binding to be grouped with other led bindings
than with gpio drivers.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Tim Gardner [Tue, 4 Dec 2012 19:52:28 +0000 (12:52 -0700)]
lib/Makefile: Fix oid_registry build dependency
It is $(obj)/oid_registry.o that is dependent on $(obj)/oid_registry_data.c.
The object file cannot be built until $(obj)/oid_registry_data.c has been
generated.
A periodic and hard to reproduce parallel build failure is due to
this incorrect lib/Makefile dependency. The compile error is completely
disingenuous.
GEN lib/oid_registry_data.c
Compiling 49 OIDs
CC lib/oid_registry.o
gcc: error: lib/oid_registry.c: No such file or directory
gcc: fatal error: no input files
compilation terminated.
make[3]: *** [lib/oid_registry.o] Error 4
Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Akinobu Mita <akinobu.mita@gmail.com> Cc: Michel Lespinasse <walken@google.com> Cc: David Howells <dhowells@redhat.com> Cc: "David S. Miller" <davem@davemloft.net> Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Linus Walleij [Sat, 1 Dec 2012 18:05:16 +0000 (19:05 +0100)]
irqdomain: update documentation
This updates the IRQdomain documentation a bit, by adding a more
verbose explanation to why we need this, and by adding some
extended documentation of the irq_domain_simple() usecase.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
James Hogan [Wed, 5 Dec 2012 16:08:24 +0000 (16:08 +0000)]
of/vendor-prefixes: add Imagination Technologies
The "powervr" prefix which is currently described as "Imagination
Technologies" isn't really appropriate for non-PowerVR hardware, so
deprecate it, changing the description of "powervr" to "PowerVR
(deprecated, use img)", and add a separate "img" prefix for "Imagination
Technologies Ltd.".
Signed-off-by: James Hogan <james.hogan@imgtec.com> Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
MIPS: Fix endless loop when processing signals for kernel tasks
The problem occurs [1] when a kernel-mode task returns from a system
call with a pending signal.
A real-life scenario is a child of 'khelper' returning from a failed
kernel_execve() in ____call_usermodehelper() [ kernel/kmod.c ].
kernel_execve() fails due to a pending SIGKILL, which is the result of
"kill -9 -1" (at least, busybox's init does it upon reboot).
The loop is as follows:
* syscall_exit_work:
- work_pending: // start_of_the_loop
- work_notifysig:
- do_notify_resume()
- do_signal()
- if (!user_mode(regs)) return;
- resume_userspace // TIF_SIGPENDING is still set
- work_pending // so we call work_pending => goto
// start_of_the_loop
More information can be found in another LKML thread:
http://www.serverphorums.com/read.php?12,457826
[1] The problem was also reproduced on !CONFIG_VM86 x86, and the
following fix was accepted.
Guenter Roeck [Tue, 9 Oct 2012 19:27:12 +0000 (12:27 -0700)]
hwmon: (coretemp) Drop dependency on PCI for TjMax detection on Atom CPUs
So far, we use the NM10 Express Chipset PCI chip ID to detect TjMax for
Atom CPUs with model 0x1c. As it turns out, we can use the CPU stepping
(x86_mask) for the same purpose; stepping is 10 for all model 0x1c CPUs
with TjMax of 100 degrees C. This was verified by checking the output of
/proc/cpuinfo for the respective CPUs (D4xx, D5xx, N4xx, N5xx).
Other CPUs currently covered by the same code (Exx, Z6xx, Z2460) are not
supported by the NM10 Express Chipset. Most of those CPUs have TjMax of 90
degrees C, except for E6xxT models which have a TjMax of 110 degrees C.
E6xxT CPUs can however not be detected by software.
Calculate TjMax for Atom CPUs as follows. Note that the listed values are not
correct in some cases (230, 330). tjmax_table is used for those to override
the default values.
ID Stepping TjMax Models
0x1c 10 100 D4xx, N4xx, D5xx, N5xx
0x1c not 10 90 Z5xx, N2xx, 230, 330, others
0x26 - 90 Atom Tunnel Creek (Exx),
Lincroft (Z6xx)
0x27 - 90 Atom Medfield (Z2460)
0x36 - 100 Atom Cedar Trail (N2xxx, D2xxx)
Also drop the module dependency on PCI.
Signed-off-by: Guenter Roeck <linux@roeck-us.net> Acked-by: Jean Delvare <khali@linux-fr.org>
The ADS7830 device is almost the same as the ADS7828,
except that it does 8-bit sampling, instead of 12-bit.
This patch extends the ads7828 driver to support this chip.
Vivien Didelot [Wed, 3 Oct 2012 20:54:07 +0000 (16:54 -0400)]
hwmon: (ads7828) driver cleanup
As there is no reliable way to identify the chip, it is preferable to
remove the detect callback, to avoid misdetection.
Module parameters are not worth it here, so let's get rid of them and
add an ads7828_platform_data structure instead.
Clean the code by removing unused macros, fixing coding style issues,
avoiding function prototypes and using convenient macros such as
module_i2c_driver().
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com> Signed-off-by: Guenter Roeck <linux@roeck-us.net>
David Howells [Mon, 22 Oct 2012 14:05:55 +0000 (15:05 +0100)]
ASN.1: Fix an indefinite length skip error
Fix an error in asn1_find_indefinite_length() whereby small definite length
elements of size 0x7f are incorrecly classified as non-small. Without this
fix, an error will be given as the length of the length will be perceived as
being very much greater than the maximum supported size.
Signed-off-by: David Howells <dhowells@redhat.com> Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
David Howells [Mon, 22 Oct 2012 14:05:48 +0000 (15:05 +0100)]
MODSIGN: Don't use enum-type bitfields in module signature info block
Don't use enum-type bitfields in the module signature info block as we can't be
certain how the compiler will handle them. As I understand it, it is arch
dependent, and it is possible for the compiler to rearrange them based on
endianness and to insert a byte of padding to pad the three enums out to four
bytes.
Instead use u8 fields for these, which the compiler should emit in the right
order without padding.
Signed-off-by: David Howells <dhowells@redhat.com> Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Thomas Gleixner [Tue, 4 Dec 2012 17:59:34 +0000 (18:59 +0100)]
watchdog: Fix CPU hotplug regression
Norbert reported:
"3.7-rc6 booted with nmi_watchdog=0 fails to suspend to RAM or
offline CPUs. It's reproducable with a KVM guest and physical
system."
The reason is that commit bcd951cf(watchdog: Use hotplug thread
infrastructure) missed to take this into account. So the cpu offline
code gets stuck in the teardown function because it accesses non
initialized data structures.
Add a check for watchdog_enabled into that path to cure the issue.
Linus Walleij [Tue, 27 Nov 2012 19:15:20 +0000 (20:15 +0100)]
clk: ux500: fix bit error
This fixes a bit error in the U8500 clock implementation: the
unused p2_pclk12 registered at bit 12 in periphereral group 6
was defined as using bit 11 rather than bit 12.
When walking over and disabling the unused clocks in the tree
at late init time, p2_pclk12 was disabled, by effectively
clearing the but for p2_pclk11 instead of bit 12 as it should
have, thus disabling gpio block 6 and 7.
Reported-by: Lee Jones <lee.jones@linaro.org> Acked-by: Ulf Hansson <ulf.hansson@linaro.org> Cc: Philippe Begnic <philippe.begnic@st.com> Cc: stable@kernel.org Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Mike Turquette <mturquette@linaro.org>
Linus Torvalds [Tue, 4 Dec 2012 17:32:12 +0000 (09:32 -0800)]
Merge branch 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux
Pull module fixes from Rusty Russell:
"Module signing build fixes for blackfin and metag"
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux:
modsign: add symbol prefix to certificate list
linux/kernel.h: define SYMBOL_PREFIX
Linus Torvalds [Tue, 4 Dec 2012 17:15:51 +0000 (09:15 -0800)]
Merge tag 'upstream-3.7-rc9' of git://git.infradead.org/linux-ubi
Pull UBI changes from Artem Bityutskiy:
"Fixes for 2 brown-paperbag bugs introduced this merge window by the
fastmap code:
1. The UBI background thread got stuck when a bit-flip happened
because free LEBs was not removed from the "free" tree when we
started using it.
2. I/O debugging checks did not work because we called a sleeping
function in atomic context."
* tag 'upstream-3.7-rc9' of git://git.infradead.org/linux-ubi:
UBI: dont call ubi_self_check_all_ff() in __wl_get_peb()
UBI: remove PEB from free tree in get_peb_for_wl()
Linus Torvalds [Tue, 4 Dec 2012 17:02:45 +0000 (09:02 -0800)]
Merge branch 'for-3.7-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq
Pull workqueue fixes from Tejun Heo:
"So, safe fixes my ass.
Commit 8852aac25e79 ("workqueue: mod_delayed_work_on() shouldn't queue
timer on 0 delay") had the side-effect of performing delayed_work
sanity checks even when @delay is 0, which should be fine for any sane
use cases.
Unfortunately, megaraid was being overly ingenious. It seemingly
wanted to use cancel_delayed_work_sync() before cancel_work_sync() was
introduced, but didn't want to waste the space for full delayed_work
as it was only going to use 0 @delay. So, it only allocated space for
struct work_struct and then cast it to struct delayed_work and passed
it into delayed_work functions - truly awesome engineering tradeoff to
save some bytes.
Xiaotian fixed it by making megraid allocate full delayed_work for
now. It should be converted to use work_struct and cancel_work_sync()
but I think we better do that after 3.7.
I added another commit to change BUG_ON()s in __queue_delayed_work()
to WARN_ON_ONCE()s so that the kernel doesn't crash even if there are
more such abuses."
* 'for-3.7-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq:
workqueue: convert BUG_ON()s in __queue_delayed_work() to WARN_ON_ONCE()s
megaraid: fix BUG_ON() from incorrect use of delayed work
Ralf Baechle [Tue, 4 Dec 2012 16:40:44 +0000 (17:40 +0100)]
MIPS: N32: Fix preadv(2) and pwritev(2) entry points.
By using the native syscall entry point the kernel was also expecting
64-bit iovec structures.
This is broken since ddd9e91b71072b8ebe89311c3a44b077defa1756 [preadv/
pwritev: MIPS: Add preadv(2) and pwritev(2) syscalls.] which originally
added these two syscalls. I walked through piles of code, including
libc and couldn't find anything that would have worked around the issue
so this change the API to what it should always have been.
Pull sparc fixes from David Miller:
"Two small fixes for Sparc, nobody uses sparc, so these are low risk :-)
1) Piggyback is too picky about the symbol types that _start and _end
have in the final kernel image, and it thus breaks with newer
binutils. Future proof by getting rid of the symbol type checks.
2) exit_group() should kill register windows on sparc64 the same way
we do for plain exit(). Thanks to Al Viro for spotting this."
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
sparc: Fix piggyback with newer binutils.
sparc64: exit_group should kill register windows just like plain exit.
Linus Torvalds [Tue, 4 Dec 2012 16:25:11 +0000 (08:25 -0800)]
vfs: avoid "attempt to access beyond end of device" warnings
The block device access simplification that avoided accessing the (racy)
block size information (commit bbec0270bdd8: "blkdev_max_block: make
private to fs/buffer.c") no longer checks the maximum block size in the
block mapping path.
That was _almost_ as simple as just removing the code entirely, because
the readers and writers all check the size of the device anyway, so
under normal circumstances it "just worked".
However, the block size may be such that the end of the device may
straddle one single buffer_head. At which point we may still want to
access the end of the device, but the buffer we use to access it
partially extends past the end.
The 'bd_set_size()' function intentionally sets the block size to avoid
this, but mounting the device - or setting the block size by hand to
some other value - can modify that block size.
So instead, teach 'submit_bh()' about the special case of the buffer
head straddling the end of the device, and turning such an access into a
smaller IO access, avoiding the problem.
This, btw, also means that unlike before, we can now access the whole
device regardless of device block size setting. So now, even if the
device size is only 512-byte aligned, we can read and write even the
last sector even when having a much bigger block size for accessing the
rest of the device.
So with this, we could now get rid of the 'bd_set_size()' block size
code entirely - resulting in faster IO for the common case - but that
would be a separate patch.
Reported-and-tested-by: Romain Francoise <romain@orebokech.com> Reporeted-and-tested-by: Meelis Roos <mroos@linux.ee> Reported-by: Tony Luck <tony.luck@intel.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Tejun Heo [Tue, 4 Dec 2012 15:40:39 +0000 (07:40 -0800)]
workqueue: convert BUG_ON()s in __queue_delayed_work() to WARN_ON_ONCE()s
8852aac25e ("workqueue: mod_delayed_work_on() shouldn't queue timer on
0 delay") unexpectedly uncovered a very nasty abuse of delayed_work in
megaraid - it allocated work_struct, casted it to delayed_work and
then pass that into queue_delayed_work().
Previously, this was okay because 0 @delay short-circuited to
queue_work() before doing anything with delayed_work. 8852aac25e
moved 0 @delay test into __queue_delayed_work() after sanity check on
delayed_work making megaraid trigger BUG_ON().
Although megaraid is already fixed by c1d390d8e6 ("megaraid: fix
BUG_ON() from incorrect use of delayed work"), this patch converts
BUG_ON()s in __queue_delayed_work() to WARN_ON_ONCE()s so that such
abusers, if there are more, trigger warning but don't crash the
machine.
David Daney [Mon, 3 Dec 2012 20:44:26 +0000 (12:44 -0800)]
MIPS: Avoid mcheck by flushing page range in huge_ptep_set_access_flags()
Problem:
1) Huge page mapping of anonymous memory is initially invalid. Will be
faulted in by copy-on-write mechanism.
2) Userspace attempts store at the end of the huge mapping.
3) TLB Refill exception handler fill TLB with a normal (4K sized)
invalid page at the end of the huge mapping virtual address range.
4) Userspace restarted, and re-attempts the store at the end of the
huge mapping.
5) Page from #3 is invalid, we get a fault and go to the hugepage
fault handler. This tries to map a huge page and calls
huge_ptep_set_access_flags() to install the mapping.
6) We just call the generic ptep_set_access_flags() to set up the page
tables, but the flush there assumes a normal (4K sized) page and
only tries to flush the first part of the huge page virtual address
out of the TLB, since the existing entry from step #3 doesn't
conflict, nothing is flushed.
7) We attempt to load the mapping into the TLB, but because it
conflicts with the entry from step #3, we get a Machine Check
exception.
The fix: Flush the entire rage covered by the huge page in
huge_ptep_set_access_flags(), and remove the optimization in
local_flush_tlb_range() so that the flush actually does the correct
thing.
Xiaotian Feng [Tue, 4 Dec 2012 11:33:54 +0000 (19:33 +0800)]
megaraid: fix BUG_ON() from incorrect use of delayed work
megaraid use INIT_WORK to declare a hotplug_work, but cast the
hotplug_work from work_struct to delayed_work and
schedule_delayed_work on it. This is very dangerous, as other part of
delayed_work might be kernel memories allocated by others.
With commit 8852aac ("workqueue: mod_delayed_work_on() shouldn't queue
timer on 0 delay"), schedule_delayed_work() will check dwork->timer
before queue_work even when @delay is 0, this causes megaraid code to
hit the BUG_ON() in workqueue code. Change megaraid code to use
delayed work.
UBI: dont call ubi_self_check_all_ff() in __wl_get_peb()
As ubi_self_check_all_ff() might sleep we are not allowed
to call it from atomic context.
For now we call it only from ubi_wl_get_peb().
There are some code paths where it would also make sense,
but these paths are currently atomic and only enabled
when fastmap is used.
Signed-off-by: Richard Weinberger <richard@nod.at> Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Stephen Warren [Tue, 27 Nov 2012 23:29:15 +0000 (16:29 -0700)]
microblaze: use new common dtc rule
The current rules have the .dtb files build in a different directory
from the .dts files. This patch changes microblaze to use the generic dtb
rule which builds .dtb files in the same directory as the source .dts.
This requires moving parts of arch/microblaze/boot/Makefile into newly
created arch/microblaze/boot/dts/Makefile, and updating
arch/microblaze/Makefile to call the new Makefile. linked_dtb.S is also
moved into boot/dts/ since it's used by rules that were moved.
Cc: Michal Simek <monstr@monstr.eu> Cc: microblaze-uclinux@itee.uq.edu.au Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Stephen Warren [Tue, 27 Nov 2012 23:29:14 +0000 (16:29 -0700)]
c6x: use new common dtc rule
The current rules have the .dtb files build in a different directory
from the .dts files. This patch changes c6x to use the generic dtb
rule which builds .dtb files in the same directory as the source .dts.
This requires moving parts of arch/c6x/boot/Makefile into newly created
arch/c6x/boot/dts/Makefile, and updating arch/c6x/Makefile to call the
new Makefile. linked_dtb.S is also moved into boot/dts/ since it's used
by rules that were moved.
Acked-by: Mark Salter <msalter@redhat.com> Cc: Aurelien Jacquiot <a-jacquiot@ti.com> Cc: linux-c6x-dev@linux-c6x.org Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Stephen Warren [Tue, 27 Nov 2012 23:29:13 +0000 (16:29 -0700)]
openrisc: use new common dtc rule
The current rules have the .dtb files build in a different directory
from the .dts files. This patch changes openrisc to use the generic dtb
rule which builds .dtb files in the same directory as the source .dts.
This requires renaming arch/openrisc/boot/Makefile to
arch/openrisc/boot/dts/Makefile, and updating arch/openrisc/Makefile to
call the new Makefile.
Cc: Jonas Bonn <jonas@southpole.se> Cc: linux@lists.openrisc.net Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Linus Torvalds [Mon, 3 Dec 2012 19:13:32 +0000 (11:13 -0800)]
Merge branch 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media fixes from Mauro Carvalho Chehab:
"Some driver fixes for s5p/exynos (mostly race fixes)"
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
[media] s5p-mfc: Handle multi-frame input buffer
[media] s5p-mfc: Bug fix of timestamp/timecode copy mechanism
[media] exynos-gsc: Add missing video device vfl_dir flag initialization
[media] exynos-gsc: Fix settings for input and output image RGB type
[media] exynos-gsc: Don't use mutex_lock_interruptible() in device release()
[media] fimc-lite: Don't use mutex_lock_interruptible() in device release()
[media] s5p-fimc: Don't use mutex_lock_interruptible() in device release()
[media] s5p-fimc: Prevent race conditions during subdevs registration
Al Viro [Mon, 3 Dec 2012 18:15:30 +0000 (18:15 +0000)]
[parisc] open(2) compat bug
In commit 9d73fc2d641f ("open*(2) compat fixes (s390, arm64)") I said:
>
> The usual rules for open()/openat()/open_by_handle_at() are
> 1) native 32bit - don't force O_LARGEFILE in flags
> 2) native 64bit - force O_LARGEFILE in flags
> 3) compat on 64bit host - as for native 32bit
> 4) native 32bit ABI for 64bit system (mips/n32, x86/x32) - as for native 64bit
>
> There are only two exceptions - s390 compat has open() forcing O_LARGEFILE and
> arm64 compat has open_by_handle_at() doing the same thing. The same binaries
> on native host (s390/31 and arm resp.) will *not* force O_LARGEFILE, so IMO
> both are emulation bugs.
Three exceptions, actually - parisc open() is another case like that.
Native 32bit won't force O_LARGEFILE, the same binary on parisc64 will.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Between commits 8323f26ce342 ("sched: Fix race in task_group()") and 800d4d30c8f2 ("sched, autogroup: Stop going ahead if autogroup is
disabled"), autogroup is a wreck.
With both applied, all you have to do to crash a box is disable
autogroup during boot up, then reboot.. boom, NULL pointer dereference
due to commit 800d4d30c8f2 not allowing autogroup to move things, and
commit 8323f26ce342 making that the only way to switch runqueues:
Linus Torvalds [Mon, 3 Dec 2012 18:53:25 +0000 (10:53 -0800)]
Merge branch 'block-dev'
Merge 'block-dev' branch.
I was going to just mark everything here for stable and leave it to the
3.8 merge window, but having decided on doing another -rc, I migth as
well merge it now.
This removes the bd_block_size_semaphore semaphore that was added in
this release to fix a race condition between block size changes and
block IO, and replaces it with atomicity guaratees in fs/buffer.c
instead, along with simplifying fs/block-dev.c.
This removes more lines than it adds, makes the code generally simpler,
and avoids the latency/rt issues that the block size semaphore
introduced for mount.
I'm not happy with the timing, but it wouldn't be much better doing this
during the merge window and then having some delayed back-port of it
into stable.
* block-dev:
blkdev_max_block: make private to fs/buffer.c
direct-io: don't read inode->i_blkbits multiple times
blockdev: remove bd_block_size_semaphore again
fs/buffer.c: make block-size be per-page and protected by the page lock
Stephen Warren [Tue, 27 Nov 2012 23:29:12 +0000 (16:29 -0700)]
arm64: use new common dtc rule
The current rules have the .dtb files build in a different directory
from the .dts files. This patch changes arm64 to use the generic dtb
rule which builds .dtb files in the same directory as the source .dts.
This requires moving parts of arch/arm64/boot/Makefile into newly created
arch/arm64/boot/dts/Makefile, and updating arch/arm64/Makefile to call the
new Makefile.
Acked-by: Catalin Marinas <catalin.marinas@arm.com> Cc: linux-arm-kernel@lists.infradead.org Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Grant Likely [Tue, 27 Nov 2012 23:29:11 +0000 (16:29 -0700)]
ARM: dt: change .dtb build rules to build in dts directory
The current rules have the .dtb files build in a different directory
from the .dts files. The only reason for this is that it was what
PowerPC has done historically. This patch changes ARM to use the generic
dtb rule which builds .dtb files in the same directory as the source .dts.
Cc: Russell King <linux@arm.linux.org.uk> Cc: Arnd Bergmann <arnd@arndb.de> Acked-by: Olof Johansson <olof@lixom.net> Cc: linux-arm-kernel@lists.infradead.org Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
[swarren: added rm command for old stale .dtb files] Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Rob Herring <rob.herring@calxeda.com>
James Hogan [Fri, 23 Nov 2012 12:08:16 +0000 (12:08 +0000)]
modsign: add symbol prefix to certificate list
Add the arch symbol prefix (if applicable) to the asm definition of
modsign_certificate_list and modsign_certificate_list_end. This uses the
recently defined SYMBOL_PREFIX which is derived from
CONFIG_SYMBOL_PREFIX.
This fixes the build of module signing on the blackfin and metag
architectures.
Signed-off-by: James Hogan <james.hogan@imgtec.com> Cc: Rusty Russell <rusty@rustcorp.com.au> Cc: David Howells <dhowells@redhat.com> Cc: Mike Frysinger <vapier@gentoo.org> Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
James Hogan [Fri, 23 Nov 2012 12:08:15 +0000 (12:08 +0000)]
linux/kernel.h: define SYMBOL_PREFIX
Define SYMBOL_PREFIX to be the same as CONFIG_SYMBOL_PREFIX if set by
the architecture, or "" otherwise. This avoids the need for ugly #ifdefs
whenever symbols are referenced in asm blocks.
Signed-off-by: James Hogan <james.hogan@imgtec.com> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Joe Perches <joe@perches.com> Cc: Paul Gortmaker <paul.gortmaker@windriver.com> Cc: Jean Delvare <khali@linux-fr.org> Cc: Ralf Baechle <ralf@linux-mips.org> Cc: Mike Frysinger <vapier@gentoo.org> Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Al Viro [Sun, 2 Dec 2012 17:55:07 +0000 (17:55 +0000)]
open*(2) compat fixes (s390, arm64)
The usual rules for open()/openat()/open_by_handle_at() are
1) native 32bit - don't force O_LARGEFILE in flags
2) native 64bit - force O_LARGEFILE in flags
3) compat on 64bit host - as for native 32bit
4) native 32bit ABI for 64bit system (mips/n32, x86/x32) - as for
native 64bit
There are only two exceptions - s390 compat has open() forcing
O_LARGEFILE and arm64 compat has open_by_handle_at() doing the same
thing. The same binaries on native host (s390/31 and arm resp.) will
*not* force O_LARGEFILE, so IMO both are emulation bugs.
Objections? The fix is obvious...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Sun, 2 Dec 2012 01:55:13 +0000 (17:55 -0800)]
Merge branch 'for-3.7-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq
Pull late workqueue fixes from Tejun Heo:
"Unfortunately, I have two really late fixes. One was for a
long-standing bug and queued for 3.8 but I found out about a
regression introduced during 3.7-rc1 two days ago, so I'm sending out
the two fixes together.
The first (long-standing) one is rescuer_thread() entering exit path
w/ TASK_INTERRUPTIBLE. It only triggers on workqueue destructions
which isn't very frequent and the exit path can usually survive being
called with TASK_INTERRUPT, so it was hidden pretty well. Apparently,
if you're reiserfs, this could lead to the exiting kthread sleeping
indefinitely holding a mutex, which is never good.
The fix is simple - restoring TASK_RUNNING before returning from the
kthread function.
The second one is introduced by the new mod_delayed_work().
mod_delayed_work() was missing special case handling for 0 delay.
Instead of queueing the work item immediately, it queued the timer
which expires on the closest next tick. Some users of the new
function converted from "[__]cancel_delayed_work() +
queue_delayed_work()" combination became unhappy with the extra delay.
Block unplugging led to noticeably higher number of context switches
and intel 6250 wireless failed to associate with WPA-Enterprise
network. The fix, again, is fairly simple. The 0 delay special case
logic from queue_delayed_work_on() should be moved to
__queue_delayed_work() which is shared by both queue_delayed_work_on()
and mod_delayed_work_on().
The first one is difficult to trigger and the failure mode for the
latter isn't completely catastrophic, so missing these two for 3.7
wouldn't make it a disastrous release, but both bugs are nasty and the
fixes are fairly safe"
* 'for-3.7-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq:
workqueue: mod_delayed_work_on() shouldn't queue timer on 0 delay
workqueue: exit rescuer_thread() as TASK_RUNNING
Eric Dumazet [Sat, 1 Dec 2012 13:07:02 +0000 (13:07 +0000)]
tcp: fix crashes in do_tcp_sendpages()
Recent network changes allowed high order pages being used
for skb fragments.
This uncovered a bug in do_tcp_sendpages() which was assuming its caller
provided an array of order-0 page pointers.
We only have to deal with a single page in this function, and its order
is irrelevant.
Reported-by: Willy Tarreau <w@1wt.eu> Tested-by: Willy Tarreau <w@1wt.eu> Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Tejun Heo [Sun, 2 Dec 2012 00:23:42 +0000 (16:23 -0800)]
workqueue: mod_delayed_work_on() shouldn't queue timer on 0 delay
8376fe22c7 ("workqueue: implement mod_delayed_work[_on]()")
implemented mod_delayed_work[_on]() using the improved
try_to_grab_pending(). The function is later used, among others, to
replace [__]candel_delayed_work() + queue_delayed_work() combinations.
Unfortunately, a delayed_work item w/ zero @delay is handled slightly
differently by mod_delayed_work_on() compared to
queue_delayed_work_on(). The latter skips timer altogether and
directly queues it using queue_work_on() while the former schedules
timer which will expire on the closest tick. This means, when @delay
is zero, that [__]cancel_delayed_work() + queue_delayed_work_on()
makes the target item immediately executable while
mod_delayed_work_on() may induce delay of upto a full tick.
This somewhat subtle difference breaks some of the converted users.
e.g. block queue plugging uses delayed_work for deferred processing
and uses mod_delayed_work_on() when the queue needs to be immediately
unplugged. The above problem manifested as noticeably higher number
of context switches under certain circumstances.
The difference in behavior was caused by missing special case handling
for 0 delay in mod_delayed_work_on() compared to
queue_delayed_work_on(). Joonsoo Kim posted a patch to add it -
("workqueue: optimize mod_delayed_work_on() when @delay == 0")[1].
The patch was queued for 3.8 but it was described as optimization and
I missed that it was a correctness issue.
As both queue_delayed_work_on() and mod_delayed_work_on() use
__queue_delayed_work() for queueing, it seems that the better approach
is to move the 0 delay special handling to the function instead of
duplicating it in mod_delayed_work_on().
Fix the problem by moving 0 delay special case handling from
queue_delayed_work_on() to __queue_delayed_work(). This replaces
Joonsoo's patch.
Mike Galbraith [Wed, 28 Nov 2012 06:17:18 +0000 (07:17 +0100)]
workqueue: exit rescuer_thread() as TASK_RUNNING
A rescue thread exiting TASK_INTERRUPTIBLE can lead to a task scheduling
off, never to be seen again. In the case where this occurred, an exiting
thread hit reiserfs homebrew conditional resched while holding a mutex,
bringing the box to its knees.
Linus Torvalds [Sat, 1 Dec 2012 21:29:55 +0000 (13:29 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull vfs fixes from Al Viro:
"A bunch of fixes; the last one is this cycle regression, the rest are
-stable fodder."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
fix off-by-one in argument passed by iterate_fd() to callbacks
lookup_one_len: don't accept . and ..
cifs: get rid of blind d_drop() in readdir
nfs_lookup_revalidate(): fix a leak
don't do blind d_drop() in nfs_prime_dcache()
Linus Torvalds [Sat, 1 Dec 2012 21:08:36 +0000 (13:08 -0800)]
Merge branch 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull RCU fix from Ingo Molnar:
"Fix leaking RCU extended quiescent state, which might trigger warnings
and mess up the extended quiescent state tracking logic into thinking
that we are in "RCU user mode" while we aren't."
* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
rcu: Fix unrecovered RCU user mode in syscall_trace_leave()
Linus Torvalds [Sat, 1 Dec 2012 21:07:48 +0000 (13:07 -0800)]
Merge branch 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf fixes from Ingo Molnar:
"This is mostly about unbreaking architectures that took the UAPI
changes in the v3.7 cycle, plus misc fixes."
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf kvm: Fix building perf kvm on non x86 arches
perf kvm: Rename perf_kvm to perf_kvm_stat
perf: Make perf build for x86 with UAPI disintegration applied
perf powerpc: Use uapi/unistd.h to fix build error
tools: Pass the target in descend
tools: Honour the O= flag when tool build called from a higher Makefile
tools: Define a Makefile function to do subdir processing
x86: Export asm/{svm.h,vmx.h,perf_regs.h}
perf tools: Fix strbuf_addf() when the buffer needs to grow
perf header: Fix numa topology printing
perf, powerpc: Fix hw breakpoints returning -ENOSPC
Linus Torvalds [Sat, 1 Dec 2012 00:59:50 +0000 (16:59 -0800)]
Merge tag 'for-linus' of git://linux-c6x.org/git/projects/linux-c6x-upstreaming
Pull C6X fixes from Mark Salter.
* tag 'for-linus' of git://linux-c6x.org/git/projects/linux-c6x-upstreaming:
c6x: use generic kvm_para.h
c6x: remove internal kernel symbols from exported setup.h
c6x: fix misleading comment
c6x: run do_notify_resume with interrupts enabled
Linus Torvalds [Sat, 1 Dec 2012 00:58:55 +0000 (16:58 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/signal
Pull assorted signal-related fixes from Al Viro:
"uml regression fix (braino in sys_execve() patch) + a bunch of fucked
sigaltstack-on-rt_sigreturn uses, similar to sparc64 fix that went in
through davem's tree. m32r horrors not included - that one's waiting
for maintainer."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/signal:
microblaze: rt_sigreturn is too trigger-happy about sigaltstack errors
score: do_sigaltstack() expects a userland pointer...
sh64: fix altstack switching on sigreturn
openrisk: fix altstack switching on sigreturn
um: get_safe_registers() should be done in flush_thread(), not start_thread()
Linus Torvalds [Sat, 1 Dec 2012 00:57:18 +0000 (16:57 -0800)]
Merge branch 'for-linus' of git://git.samba.org/sfrench/cifs-2.6
Pull CIFS fixes from Steve French:
"Two low risk, small fixes, that fix cifs regressions introduced in
3.7."
* 'for-linus' of git://git.samba.org/sfrench/cifs-2.6:
CIFS: Fix wrong buffer pointer usage in smb_set_file_info
cifs: fix writeback race with file that is growing
Pull target fix from Nicholas Bellinger:
"So just a single target fix for v3.7.0 this time around from Roland to
address a aborted command bug w/ tcm_qla2xxx fabric ports.
Also, there is one outstanding IBLOCK + virtio-blk bug that is still
being tracked down effecting v3.6.x, but AFAICT thus far this appears
to be a bug outside of target code."
* git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
target: Fix handling of aborted commands
Vincent Palatin [Fri, 30 Nov 2012 20:15:32 +0000 (12:15 -0800)]
x86, fpu: Avoid FPU lazy restore after suspend
When a cpu enters S3 state, the FPU state is lost.
After resuming for S3, if we try to lazy restore the FPU for a process running
on the same CPU, this will result in a corrupted FPU context.
Ensure that "fpu_owner_task" is properly invalided when (re-)initializing a CPU,
so nobody will try to lazy restore a state which doesn't exist in the hardware.
Tested with a 64-bit kernel on a 4-core Ivybridge CPU with eagerfpu=off,
by doing thousands of suspend/resume cycles with 4 processes doing FPU
operations running. Without the patch, a process is killed after a
few hundreds cycles by a SIGFPE.
Cc: Duncan Laurie <dlaurie@chromium.org> Cc: Olof Johansson <olofj@chromium.org> Cc: <stable@kernel.org> v3.4+ # for 3.4 need to replace this_cpu_write by percpu_write Signed-off-by: Vincent Palatin <vpalatin@chromium.org> Link: http://lkml.kernel.org/r/1354306532-1014-1-git-send-email-vpalatin@chromium.org Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Linus Torvalds [Fri, 30 Nov 2012 18:47:55 +0000 (10:47 -0800)]
Merge branch 'drm-fixes' of git://people.freedesktop.org/~airlied/linux
Pull DRM fixes from Dave Airlie:
"Just driver fixes, nothing major, except maybe the Ironlake rc6
disable:
- intel:
* revert ironlake rc6 - we still have one ilk regression, but this
gets rid of one big one
* turn off cloning
* a directed fix for Apple edp
- radeon: one modesetting fix
- exynos: minor fixes"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
radeon: fix pll/ctrc mapping on dce2 and dce3 hardware
Revert "drm/i915: enable rc6 on ilk again"
drm/i915: do not default to 18 bpp for eDP if missing from VBT
drm/exynos: Fix potential NULL pointer dereference in exynos_drm_encoder.c
drm/exynos: Make exynos4/5_fimd_driver_data static
drm/exynos: fix overlay updating issue
drm/exynos: remove unnecessary code.
drm/exynos: fix linux framebuffer address setting.
drm/i915: disable cloning on sdvo
Linus Torvalds [Fri, 30 Nov 2012 18:46:43 +0000 (10:46 -0800)]
Merge branch 'akpm' (Fixes from Andrew)
Merge misc fixes from Andrew Morton:
"Seven fixes, some of them fingers-crossed :("
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (7 patches)
drivers/rtc/rtc-tps65910.c: fix invalid pointer access on _remove()
mm: soft offline: split thp at the beginning of soft_offline_page()
mm: avoid waking kswapd for THP allocations when compaction is deferred or contended
revert "Revert "mm: remove __GFP_NO_KSWAPD""
mm: vmscan: fix endless loop in kswapd balancing
mm/vmemmap: fix wrong use of virt_to_page
mm: compaction: fix return value of capture_free_page()
Linus Torvalds [Fri, 30 Nov 2012 18:30:34 +0000 (10:30 -0800)]
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Arnd Bergmann:
"These are three fixes for the Marvell EBU family and one for the
Samsung s3c platforms. All of them are obvious should still make it
into 3.7."
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: Kirkwood: Update PCI-E fixup
Dove: Fix irq_to_pmu()
Dove: Attempt to fix PMU/RTC interrupts
ARM: S3C24XX: Fix potential NULL pointer dereference error
Linus Torvalds [Fri, 30 Nov 2012 18:28:09 +0000 (10:28 -0800)]
Merge tag 'ixp4xx-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM ixp4xx bug fixes from Arnd Bergmann:
"These were originally prepared by Krzysztof Halasa but not submitted
in time for v3.7 due to some confusion about how ixp4xx patches should
be handled. Jason Cooper thankfully offered to help out sending the
patches upstream through arm-soc now, but given the timing, we could
as well delay them for 3.8."
* tag 'ixp4xx-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
IXP4xx: use __iomem for MMIO
IXP4xx: map CPU config registers within VMALLOC region.
IXP4xx: Always ioremap() Queue Manager MMIO region at boot.
ixp4xx: Declare MODULE_FIRMWARE usage
IXP4xx crypto: MOD_AES{128,192,256} already include key size.
WAN: Remove redundant HDLC info printed by IXP4xx HSS driver.
IXP4xx: Remove time limit for PCI TRDY to enable use of slow devices.
IXP4xx: ixp4xx_crypto driver requires Queue Manager and NPE drivers.
IXP4xx: HW pseudo-random generator is available on IXP45x/46x only.
IXP4xx: Fix off-by-one bug in Goramo MultiLink platform.
IXP4xx: Fix Goramo MultiLink platform compilation.
projects / linux-imx.git / log