xen/xenbus: Add quirk to deal with misconfigured backends.
A rather annoying and common case is when booting a PVonHVM guest
and exposing the PV KBD and PV VFB - as broken toolstacks don't
always initialize the backends correctly.
Normally The HVM guest is using the VGA driver and the emulated
keyboard for this (though upstream version of QEMU implements
PV KBD, but still uses a VGA driver). We provide a very basic
two-stage wait mechanism - where we wait for 30 seconds for all
devices, and then for 270 for all them except the two mentioned.
That allows us to wait for the essential devices, like network
or disk for the full 6 minutes.
To trigger this, put this in your guest config:
vfb = [ 'vnc=1, vnclisten=0.0.0.0 ,vncunused=1']
instead of this:
vnc=1
vnclisten="0.0.0.0"
CC: stable@kernel.org Acked-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
[v3: Split delay in non-essential (30 seconds) and essential
devices per Ian and Stefano suggestion]
[v4: Added comments per Stefano suggestion] Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Henrik Rydberg [Thu, 12 Apr 2012 22:37:00 +0000 (00:37 +0200)]
nouveau: Set special lane map for the right chipset
The refactoring of the nv50 logic, introduced in 8663bc7c, modified the
test for the special lane map used on some Apple computers with Nvidia
chipsets. The tested MBA3,1 would still boot, but resume from suspend
stopped working. This patch restores the old test, which fixes the problem.
Signed-off-by: Henrik Rydberg <rydberg@euromail.se> Acked-by: Ben Skeggs <bskeggs@redhat.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
Merge fixes for Thinkpad docking-station regressions for 3.3 kernels
back to 3.4. These were committed in that branch to make the stable
merging easier.
ALSA: hda/conexant - Set up the missing docking-station pins
ThinkPad 410,420,510,520 and X201 with cx50585 & co chips have the
docking-station ports, but BIOS doesn't initialize for these pins.
Thus, like the former X200, we need to set up the pins manually in the
driver.
The odd part is that the same PCI SSID is used for X200 and T400, thus
we need to prepare individual fixup tables for cx5051 and others.
Dave Airlie [Thu, 19 Apr 2012 14:42:58 +0000 (15:42 +0100)]
drm/radeon: fix load detect on rn50 with hardcoded EDIDs.
When the force changes went in back in 3.3.0, we ended up returning
disconnected in the !force case, and the connected in when forced,
as it hit the hardcoded check.
Fix it so all exits go via the hardcoded check and stop spurious
modesets on platforms with hardcoded EDIDs.
Reported-by: Evan McNabb (Red Hat) Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Cc: stable@vger.kernel.org Signed-off-by: Dave Airlie <airlied@redhat.com>
drm: Releasing FBs before releasing GEM objects during drm_release
During DRM release, all the FBs and gem objects are released. If
a gem object is being used as a FB and set to a crtc, it must not
be freed before releasing the framebuffer first.
If FBs are released first, the crtc using the FB is disabled first
so now the GEM object can be freed safely. The CRTC will be enabled
again when the driver restores fbdev mode.
Signed-off-by: Prathyush K <prathyush.k@samsung.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
Jim Meyering [Tue, 17 Apr 2012 19:27:54 +0000 (21:27 +0200)]
drm/nouveau/pm: don't read/write beyond end of stack buffer
NUL-terminate after strncpy.
If the parameter "profile" has length 16 or more, then strncpy
leaves "string" with no NUL terminator, so the following search
for '\n' may read beyond the end of that 16-byte buffer.
If it finds a newline there, then it will also write beyond the
end of that stack buffer.
Signed-off-by: Jim Meyering <meyering@redhat.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
drivers: gpu: drm: gma500: mdfld_dsi_output.h: Remove not unneeded include of version.h
The output of "make versioncheck" points a incorrect include of
version.h in the drivers/gpu/drm/gma500/mdfld_dsi_output.h:
drivers/gpu/drm/gma500/mdfld_dsi_output.h: 32 linux/version.h not needed.
If we take a look in the file, we can agree to remove it.
Cc: David Airlie <airlied@linux.ie> Cc: <dri-devel@lists.freedesktop.org> Signed-off-by: Marcos Paulo de Souza <marcos.souza.org@gmail.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
Dave Airlie [Thu, 19 Apr 2012 13:13:52 +0000 (14:13 +0100)]
Merge branch 'drm-intel-fixes' of git://people.freedesktop.org/~danvet/drm-intel into drm-fixes
* 'drm-intel-fixes' of git://people.freedesktop.org/~danvet/drm-intel:
drm/i915: Do not set "Enable Panel Fitter" on SNB pageflips
drm/i915: Hold mode_config lock whilst changing mode for lastclose()
drm/i915: don't clobber the special upscaling lvds timings
drm/radeon/kms: fix the regression of DVI connector check
The check of the encoder type in the commit [e00e8b5e: drm/radeon/kms:
fix analog load detection on DVI-I connectors] is obviously wrong, and
it's the culprit of the regression on my workstation with DVI-analog
connection resulting in the blank output.
Fixed the typo now.
Signed-off-by: Takashi Iwai <tiwai@suse.de> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Cc: <stable@vger.kernel.org> Signed-off-by: Dave Airlie <airlied@redhat.com>
Commit 4f5ca836b "HID: hid-input: add support for HID devices reporting
Battery Strength" added the CONFIG_HID_BATTERY_STRENGTH option to report
the battery strength of HID devices. The commit log explicitly mentions
it not working properly with recent userspace, but it is default y
anyway. This is rather odd, and actually causes problems on real
systems.
This works around Fedora bug
https://bugzilla.redhat.com/show_bug.cgi?id=806295
ALSA: workaround: change the timing of alsa_sound_last_init()
Current alsa_sound_last_init() was called as __initcall().
So, on current ALSA, only devices that had been properly
registered at this point were shown.
So, it will show "No soundcards found" if driver requests
probe deferment. it's often misleading.
This patch delays the timing of alsa_sound_last_init()
as workaround.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> Reviwed-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Takashi Iwai <tiwai@suse.de>
While refactoring the mute-LED handling for HP laptops, I messed up
the polarity check in a wrong way. The red (or the mute-LED if any)
should appear in the muted state, corresponding to GPIO on.
Reported-by: Mikko Vinni <mmvinni@yahoo.com> Signed-off-by: Takashi Iwai <tiwai@suse.de>
memcg: fix Bad page state after replace_page_cache
My 9ce70c0240d0 "memcg: fix deadlock by inverting lrucare nesting" put a
nasty little bug into v3.3's version of mem_cgroup_replace_page_cache(),
sometimes used for FUSE. Replacing __mem_cgroup_commit_charge_lrucare()
by __mem_cgroup_commit_charge(), I used the "pc" pointer set up earlier:
but it's for oldpage, and needs now to be for newpage. Once oldpage was
freed, its PageCgroupUsed bit (cleared above but set again here) caused
"Bad page state" messages - and perhaps worse, being missed from newpage.
(I didn't find this by using FUSE, but in reusing the function for tmpfs.)
Olof Johansson [Thu, 19 Apr 2012 04:30:16 +0000 (21:30 -0700)]
Merge tag 'at91-fixes' of git://github.com/at91linux/linux-at91 into fixes
Here is another fixes series for AT91 designed for 3.4-rc.
We experienced some issues while compiling some drivers as modules: Joachim has
corrected several of them. We may reduce this number of exported values by
reworking some drivers, in the future.
Some drivers are also modified here, I would like to keep them in the series
as the modifications are really related with our recent move to irqdomains or
simply related with compiler annotations.
I keep dmaengine Kconfig modification in this "fixes" series. The DMA
driver will not be available for 9x5 SoC family otherwise.
* tag 'at91-fixes' of git://github.com/at91linux/linux-at91:
dmaengine: Kconfig: fix Atmel at_hdmac entry
USB: gadget/at91_udc: add gpio_to_irq() function to vbus interrupt
USB: ohci-at91: change annotations for probe/remove functions
leds-atmel-pwm.c: Make pwmled_probe() __devinit
ARM: at91: fix at91sam9261ek Ethernet dm9000 irq
ARM: at91: fix rm9200ek flash size
ARM: at91: remove empty at91_init_serial function
ARM: at91: fix typo in at91_pmc_base assembly declaration
ARM: at91: Export at91_matrix_base
ARM: at91: Export at91_pmc_base
ARM: at91: Export at91_ramc_base
ARM: at91: Export at91_st_base
Olof Johansson [Thu, 19 Apr 2012 04:28:16 +0000 (21:28 -0700)]
Merge branch 'fixes-for-arm-soc-20120416' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson into fixes
* 'fixes-for-arm-soc-20120416' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson:
ARM: ux500: update defconfig
ARM: ux500: Fix unmet direct dependency
ARM: ux500: wake secondary cpu via resched
Olof Johansson [Thu, 19 Apr 2012 04:25:52 +0000 (21:25 -0700)]
Merge tag 'v3.4-rc3-imx-fixes' of git://git.pengutronix.de/git/imx/linux-2.6 into fixes
ARM i.MX misc fixes for -rc
* tag 'v3.4-rc3-imx-fixes' of git://git.pengutronix.de/git/imx/linux-2.6:
ARM: imx: Fix imx5 idle logic bug
ARM: imx27-dt: Fix build due to removal of irq_domain_add_simple()
ARM: imx_v4_v5_defconfig: Add support for CONFIG_REGULATOR_FIXED_VOLTAGE
Paul Gortmaker [Mon, 16 Apr 2012 19:38:28 +0000 (15:38 -0400)]
ARM: bcmring: fix UART declarations
This error appeared in the bcmring_defconfig build:
CC arch/arm/mach-bcmring/core.o
arch/arm/mach-bcmring/core.c:55: error: macro "AMBA_APB_DEVICE" requires 6 arguments, but only 5 given
arch/arm/mach-bcmring/core.c:55: warning: type defaults to 'int' in declaration of 'AMBA_APB_DEVICE'
arch/arm/mach-bcmring/core.c:56: error: macro "AMBA_APB_DEVICE" requires 6 arguments, but only 5 given
arch/arm/mach-bcmring/core.c:56: warning: type defaults to 'int' in declaration of 'AMBA_APB_DEVICE'
arch/arm/mach-bcmring/core.c:134: error: 'uartA_device' undeclared here (not in a function)
arch/arm/mach-bcmring/core.c:135: error: 'uartB_device' undeclared here (not in a function)
make[2]: *** [arch/arm/mach-bcmring/core.o] Error 1
"ARM: amba: bcmring: use common amba device initializers"
Note that in include/linux/amba/bus.h we have:
#define AMBA_APB_DEVICE(name, busid, id, base, irqs, data) ...
There is an a --> A case error in the busid and a missing zero
placeholder for the id field.
Cc: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
[olof: reworded patch subject] Signed-off-by: Olof Johansson <olof@lixom.net>
Alex Williamson [Wed, 18 Apr 2012 03:46:44 +0000 (21:46 -0600)]
KVM: lock slots_lock around device assignment
As pointed out by Jason Baron, when assigning a device to a guest
we first set the iommu domain pointer, which enables mapping
and unmapping of memory slots to the iommu. This leaves a window
where this path is enabled, but we haven't synchronized the iommu
mappings to the existing memory slots. Thus a slot being removed
at that point could send us down unexpected code paths removing
non-existent pinnings and iommu mappings. Take the slots_lock
around creating the iommu domain and initial mappings as well as
around iommu teardown to avoid this race.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com> Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Add missing "personality.h"
security/commoncap.c: In function 'cap_bprm_set_creds':
security/commoncap.c:510: error: 'PER_CLEAR_ON_SETID' undeclared (first use in this function)
security/commoncap.c:510: error: (Each undeclared identifier is reported only once
security/commoncap.c:510: error: for each function it appears in.)
Avi Kivity [Wed, 18 Apr 2012 12:03:04 +0000 (15:03 +0300)]
KVM: VMX: Fix kvm_set_shared_msr() called in preemptible context
kvm_set_shared_msr() may not be called in preemptible context,
but vmx_set_msr() does so:
BUG: using smp_processor_id() in preemptible [00000000] code: qemu-kvm/22713
caller is kvm_set_shared_msr+0x32/0xa0 [kvm]
Pid: 22713, comm: qemu-kvm Not tainted 3.4.0-rc3+ #39
Call Trace:
[<ffffffff8131fa82>] debug_smp_processor_id+0xe2/0x100
[<ffffffffa0328ae2>] kvm_set_shared_msr+0x32/0xa0 [kvm]
[<ffffffffa03a103b>] vmx_set_msr+0x28b/0x2d0 [kvm_intel]
...
Making kvm_set_shared_msr() work in preemptible is cleaner, but
it's used in the fast path. Making two variants is overkill, so
this patch just disables preemption around the call.
Reported-by: Dave Jones <davej@redhat.com> Signed-off-by: Avi Kivity <avi@redhat.com> Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/fuse
Pull fuse updates from Miklos Szeredi.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/fuse:
fuse: use flexible array in fuse.h
fuse: allow nanosecond granularity
fuse: O_DIRECT support for files
fuse: fix nlink after unlink
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull s390 updates from Martin Schwidefsky:
"A couple of bug fixes, one of them is a TLB flush fix. Included as
well is one small coding style patch and a patch to update the default
configuration."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
[S390] Fix compile error in swab.h
[S390] Fix stfle() lowcore protection problem
[S390] cpum_cf: get rid of compile warnings
[S390] irq: simple coding style change
[S390] update default configuration
[S390] fix tlb flushing for page table pages
[S390] kernel: Use local_irq_save() for memcpy_real()
[S390] s390/char/vmur.c: fix memory leak
[S390] drivers/s390/block/dasd_eckd.c: add missing dasd_sfree_request
This driver anticipates pch_uart_verify_port() is not called
during installation.
However, actually pch_uart_verify_port() is called during
installation.
As a result, memory access violation occurs like below.
0. initial value: use_dma=0
1. starup()
- dma channel is not allocated because use_dma=0
2. pch_uart_verify_port()
- Set use_dma=1
3. UART processing acts DMA mode because use_dma=1
- memory access violation occurs!
This patch fixes the issue.
Solution:
Whenever pch_uart_verify_port() is called and then
dma channel is not allocated, the channel should be allocated.
Alexander Shiyan [Tue, 27 Mar 2012 08:22:49 +0000 (12:22 +0400)]
ARM: clps711x: serial driver hungs are a result of call disable_irq within ISR
Since 2.6.30-rc1 clps711x serial driver hungs system. This is a result
of call disable_irq from ISR. synchronize_irq waits for end of interrupt
and goes to infinite loop. This patch fix this problem.
This call is not needed; the IRQ controller should (and does) set up
interrupts correctly. set_irq_flags() isn't exported to modules, to
this also fixes compilation of ehci-tegra.c as a module.
Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tomoki Sekiyama [Thu, 29 Mar 2012 23:51:36 +0000 (08:51 +0900)]
USB: yurex: Fix missing URB_NO_TRANSFER_DMA_MAP flag in urb
Current probing code is setting URB_NO_TRANSFER_DMA_MAP flag into a wrong urb
structure, and this causes BUG_ON with some USB host implementations.
This patch fixes the issue.
Tomoki Sekiyama [Thu, 29 Mar 2012 23:51:28 +0000 (08:51 +0900)]
USB: yurex: Remove allocation of coherent buffer for setup-packet buffer
Removes allocation of coherent buffer for the control-request setup-packet
buffer from the yurex driver. Using coherent buffers for setup-packet is
obsolete and does not work with some USB host implementations.
Eric Dumazet [Wed, 18 Apr 2012 10:14:23 +0000 (10:14 +0000)]
tcp: fix retransmit of partially acked frames
Alexander Beregalov reported skb_over_panic errors and provided stack
trace.
I occurs commit a21d45726aca (tcp: avoid order-1 allocations on wifi and
tx path) added a regression, when a retransmit is done after a partial
ACK.
tcp_retransmit_skb() tries to aggregate several frames if the first one
has enough available room to hold the following ones payload. This is
controlled by /proc/sys/net/ipv4/tcp_retrans_collapse tunable (default :
enabled)
Problem is we must make sure _pskb_trim_head() doesnt fool
skb_availroom() when pulling some bytes from skb (this pull is done when
receiver ACK part of the frame).
Reported-by: Alexander Beregalov <a.beregalov@gmail.com> Cc: Marc MERLIN <marc@merlins.org> Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security
Pull security subsystem fixes from James Morris.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security:
fcaps: clear the same personality flags as suid when fcaps are used
mpi: Avoid using freed pointer in mpi_lshift_limbs()
Smack: move label list initialization
Lasse Collin [Wed, 18 Apr 2012 16:55:44 +0000 (19:55 +0300)]
xz: Enable BCJ filters on SPARC and 32-bit x86
The BCJ filters were meant to be enabled already on these
archs, but the xz_wrap.sh script was buggy. Enabling the
filters should give smaller kernel images.
xz_wrap.sh will now use $SRCARCH instead of $ARCH to detect
the architecture. That way it doesn't need to care about the
subarchs (like i386 vs. x86_64) since the BCJ filters don't
care either.
Signed-off-by: Lasse Collin <lasse.collin@tukaani.org> Acked-by: Jan Beulich <jbeulich@suse.com> Acked-by: H. Peter Anvin <hpa@zytor.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Alan Stern [Wed, 18 Apr 2012 15:33:00 +0000 (11:33 -0400)]
EHCI: always clear the STS_FLR status bit
This patch (as1544) fixes a problem affecting some EHCI controllers.
They can generate interrupts whenever the STS_FLR status bit is turned
on, even though that bit is masked out in the Interrupt Enable
register.
Since the driver doesn't use STS_FLR anyway, the patch changes the
interrupt routine to clear that bit whenever it is set, rather than
leaving it alone.
Merge tag 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev
Pull libara fixes from Jeff Garzik:
- Notable regression fix. Forbid dynamic runtime power management by
default, due to issues with suspend/resume and hotplug.
To re-enable, use sysfs.
- make ata_print_id atomic, due to ref from multiple contexts
- sata_mv warning fix
- ata_piix new PCI ID
* tag 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
libata: forbid port runtime pm by default, fixing regression
libata: make ata_print_id atomic
sata_mv: silence an uninitialized variable warning
ata_piix: IDE-mode SATA patch for Intel DH89xxCC DeviceIDs
drivers/block/xen-blkback/xenbus.c: In function 'xen_blkbk_discard':
drivers/block/xen-blkback/xenbus.c:419:4: warning: passing argument 1 of 'dev_warn' makes pointer from integer without a cast
+[enabled by default]
include/linux/device.h:894:5: note: expected 'const struct device *' but argument is of type 'long int'
It is unclear how that mistake made it in. It surely is wrong.
Acked-by: Jens Axboe <axboe@kernel.dk> Reported-by: Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
* commit 'c104f1fa1ecf4ee0fc06e31b1f77630b2551be81': (14566 commits)
cpufreq: OMAP: fix build errors: depends on ARCH_OMAP2PLUS
sparc64: Eliminate obsolete __handle_softirq() function
sparc64: Fix bootup crash on sun4v.
kconfig: delete last traces of __enabled_ from autoconf.h
Revert "kconfig: fix __enabled_ macros definition for invisible and un-selected symbols"
kconfig: fix IS_ENABLED to not require all options to be defined
irq_domain: fix type mismatch in debugfs output format
staging: android: fix mem leaks in __persistent_ram_init()
staging: vt6656: Don't leak memory in drivers/staging/vt6656/ioctl.c::private_ioctl()
staging: iio: hmc5843: Fix crash in probe function.
panic: fix stack dump print on direct call to panic()
drivers/rtc/rtc-pl031.c: enable clock on all ST variants
Revert "mm: vmscan: fix misused nr_reclaimed in shrink_mem_cgroup_zone()"
hugetlb: fix race condition in hugetlb_fault()
drivers/rtc/rtc-twl.c: use static register while reading time
drivers/rtc/rtc-s3c.c: add placeholder for driver private data
drivers/rtc/rtc-s3c.c: fix compilation error
MAINTAINERS: add PCDP console maintainer
memcg: do not open code accesses to res_counter members
drivers/rtc/rtc-efi.c: fix section mismatch warning
...
David Miller [Thu, 12 Apr 2012 18:37:30 +0000 (14:37 -0400)]
Fix modpost failures in fedora 17
The symbol table on x86-64 starts to have entries that have names
like:
_GLOBAL__sub_I_65535_0___mod_x86cpu_device_table
They are of type STT_FUNCTION and this one had a length of 18. This
matched the device ID validation logic and it barfed because the
length did not meet the device type's criteria.
--------------------
FATAL: arch/x86/crypto/aesni-intel: sizeof(struct x86cpu_device_id)=16 is not a modulo of the size of section __mod_x86cpu_device_table=18.
Fix definition of struct x86cpu_device_id in mod_devicetable.h
--------------------
These are some kind of compiler tool internal stuff being emitted and
not something we want to inspect in modpost's device ID table
validation code.
So skip the symbol if it is not of type STT_OBJECT.
Signed-off-by: David S. Miller <davem@davemloft.net> Acked-by: Sam Ravnborg <sam@ravnborg.org> Signed-off-by: Michal Marek <mmarek@suse.cz>
David S. Miller [Wed, 18 Apr 2012 19:26:52 +0000 (15:26 -0400)]
Merge branch 'for-davem' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless
From John:
Another batch of fixes intended for 3.4...
First up, we have a minor signedness fix for libertas from Amitkumar
Karwar. Next, Arend gives us a brcm80211 fix for correctly enabling
Tx FIFOs on channels 12 and 13. Bing Zhao gives us some register
address corrections for mwifiex. Felix give us a trio of fixes --
one for ath9k to wake the hardware properly from full sleep, one for
mac80211 to properly handle packets in cooked monitor mode, and one
for ensuring that the proper HT mode selection is honored.
Hauke gives us a bcma fix for handling the lack of an sprom. Jonathon
Bither gives us an ath5k fix for a missing THIS_MODULE build issue,
and another ath5k fix for an io mapping leak. Lukasz Kucharczyk
fixes a bitwise check in cfg80211, and Sujith gives us an ath9k fix
for assigning sequence numbers for fragmented frames. Finally, we
have a MAINTAINERS change from Wey-Yi Guy -- congrats to Johannes
Berg for taking the lead on iwlwifi. :-)
Signed-off-by: David S. Miller <davem@davemloft.net>
Andre Przywara [Mon, 9 Apr 2012 22:16:34 +0000 (18:16 -0400)]
hwmon: fam15h_power: fix bogus values with current BIOSes
Newer BKDG[1] versions recommend a different initialization value for
the running average range register in the northbridge. This improves
the power reading by avoiding counter saturations resulting in bogus
values for anything below about 80% of TDP power consumption.
Updated BIOSes will have this new value set up from the beginning,
but meanwhile we correct this value ourselves.
This needs to be done on all northbridges, even on those where the
driver itself does not register at.
This fixes the driver on all current machines to provide proper
values for idle load.
The conversion was done blindly and is wrong, as it does not provide a
primary handler to disable the level type irq on the device level.
Neither does it set the IRQF_ONESHOT flag which handles that at the irq
line level. This can't be done as the interrupt might be shared, though
we might extend the core to force it.
So an interrupt on this line will wake up the thread, but immediately
unmask the irq after that. Due to the interrupt being level type the
hardware interrupt is raised over and over and prevents the irq thread
from handling it. Fail.
request_irq() unfortunately does not refuse such a request and the patch
was obviously never tested with real interrupts.
Bisected-by: Paul Bolle <pebolle@tiscali.nl> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
[media] drxk: Does not unlock mutex if sanity check failed in scu_command()
If sanity check fails in scu_command(), goto error leads to unlock of
an unheld mutex. The check should not fail in reality, but it nevertheless
worth fixing.
Found by Linux Driver Verification project (linuxtesting.org).
[media] dvb_frontend: Fix a regression when switching back to DVB-S
There are some softwares (Kaffeine and likely xine) that uses a
DVBv5 call to switch to DVB-S2, but expects that a DVBv3 call to
switch back to DVB-S. Well, this is not right, as a DVBv3 call
doesn't know anything about delivery systems.
However, as, by accident, this used to work, we need to restore its
behavior, in order to avoid regressions with those softwares.
Reported on this Fedora 16 bugzilla:
https://bugzilla.redhat.com/show_bug.cgi?id=812895
Reported-by: Dieter Roever <Dieter.Roever@gmx.de> Cc: stable@kernel.org # for version 3.3 Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Chris Wilson [Tue, 17 Apr 2012 19:37:00 +0000 (20:37 +0100)]
drm/i915: Do not set "Enable Panel Fitter" on SNB pageflips
Not only do the pageflip work without it at non-native modes (i.e. with
the panel fitter enabled), it also causes normal (non-pageflipped)
modesets to fail.
Reported-by: Adam Jackson <ajax@redhat.com> Tested-by: Adam Jackson <ajax@redhat.com> Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Wanted-by-for-fixes: Dave Airlie <airlied@gmail.com> Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
netns: do not leak net_generic data on failed init
ops_init should free the net_generic data on
init failure and __register_pernet_operations should not
call ops_free when NET_NS is not enabled.
Signed-off-by: Julian Anastasov <ja@ssi.bg> Reviewed-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Paris [Tue, 17 Apr 2012 20:26:54 +0000 (16:26 -0400)]
fcaps: clear the same personality flags as suid when fcaps are used
If a process increases permissions using fcaps all of the dangerous
personality flags which are cleared for suid apps should also be cleared.
Thus programs given priviledge with fcaps will continue to have address space
randomization enabled even if the parent tried to disable it to make it
easier to attack.
Signed-off-by: Eric Paris <eparis@redhat.com> Reviewed-by: Serge Hallyn <serge.hallyn@canonical.com> Signed-off-by: James Morris <james.l.morris@oracle.com>
Eric Dumazet [Mon, 16 Apr 2012 23:28:07 +0000 (23:28 +0000)]
tcp: fix tcp_grow_window() for large incoming frames
tcp_grow_window() has to grow rcv_ssthresh up to window_clamp, allowing
sender to increase its window.
tcp_grow_window() still assumes a tcp frame is under MSS, but its no
longer true with LRO/GRO.
This patch fixes one of the performance issue we noticed with GRO on.
Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Neal Cardwell <ncardwell@google.com> Cc: Tom Herbert <therbert@google.com> Acked-by: Neal Cardwell <ncardwell@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Christian Riesch [Mon, 16 Apr 2012 04:35:25 +0000 (04:35 +0000)]
davinci_mdio: Fix MDIO timeout check
Under heavy load (flood ping) it is possible for the MDIO timeout to
expire before the loop checks the GO bit again. This patch adds an
additional check whether the operation was done before actually
returning -ETIMEDOUT.
To reproduce this bug, flood ping the device, e.g., ping -f -l 1000
After some time, a "timed out waiting for user access" warning
may appear. And even worse, link may go down since the PHY reported a
timeout.
Signed-off-by: Christian Riesch <christian.riesch@omicron.at> Cc: <stable@vger.kernel.org> Cc: Cyril Chemparathy <cyril@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Semantically, rt6_clean_expires() wants to do rt->dst.from = NULL instead of
rt->dst.expires = 0. It is clearing the RTF_EXPIRES flag, so the union is going
to be treated as a pointer (dst.from) not a long (dst.expires).
Signed-off-by: Jiri Bohac <jbohac@suse.cz> Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 1716a961 (ipv6: fix problem with expired dst cache) broke PMTU
discovery. rt6_update_expires() calls dst_set_expires(), which only updates
dst->expires if it has not been set previously (expires == 0) or if the new
expires is earlier than the current dst->expires.
rt6_update_expires() needs to zero rt->dst.expires, otherwise it will contain
ivalid data left over from rt->dst.from and will confuse dst_set_expires().
Signed-off-by: Jiri Bohac <jbohac@suse.cz> Signed-off-by: David S. Miller <davem@davemloft.net>
arcrimi_probe() calls BUGMSG() before register_netdev() happens. BUGMSG()
itself prints dev->name, but as the format string hasn't been expanded by
register_netdev() yet, the output contains bogus device name such as
arc%d: Given: node 00h, shmem 0h, irq 0
As we don't know the device name yet, just drop the prefix completely from
the debugging messages.
Reported-by: Steven Young <sdyoung@vt220.org> Signed-off-by: Jiri Kosina <jkosina@suse.cz> Signed-off-by: David S. Miller <davem@davemloft.net>
Jesper Juhl [Mon, 6 Feb 2012 09:07:04 +0000 (20:07 +1100)]
mpi: Avoid using freed pointer in mpi_lshift_limbs()
At the start of the function we assign 'a->d' to 'ap'. Then we use the
RESIZE_IF_NEEDED macro on 'a' - this may free 'a->d' and replace it
with newly allocaetd storage. In that case, we'll be operating on
freed memory further down in the function when we index into 'ap[]'.
Since we don't actually need 'ap' until after the use of the
RESIZE_IF_NEEDED macro we can just delay the assignment to it until
after we've potentially resized, thus avoiding the issue.
While I was there anyway I also changed the integer variable 'n' to be
const. It might as well be since we only assign to it once and use it
as a constant, and then the compiler will tell us if we ever assign to
it in the future.
A kernel with Smack enabled will fail if tmpfs has xattr support.
Move the initialization of predefined Smack label
list entries to the LSM initialization from the
smackfs setup. This became an issue when tmpfs
acquired xattr support, but was never correct.
Signed-off-by: Casey Schaufler <casey@schaufler-ca.com> Signed-off-by: James Morris <james.l.morris@oracle.com>
Alan Stern [Tue, 17 Apr 2012 19:24:15 +0000 (15:24 -0400)]
EHCI: fix criterion for resuming the root hub
This patch (as1542) changes the criterion ehci-hcd uses to tell when
it needs to resume the controller's root hub. A resume is needed when
a port status change is detected, obviously, but only if the root hub
is currently suspended.
Right now the driver tests whether the root hub is running, and that
is not the correct test. In particular, if the controller has died
then the root hub should not be restarted. In addition, some buggy
hardware occasionally requires the root hub to be running and
sending out SOF packets even while it is nominally supposed to be
suspended.
In the end, the test needs to be changed. Rather than checking whether
the root hub is currently running, the driver will now check whether
the root hub is currently suspended. This will yield the correct
behavior in all cases.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> CC: Peter Chen <B29397@freescale.com> Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These devices have a number of non serial interfaces as well. Use
the existing "Direct IP" blacklist to prevent binding to interfaces
which are handled by other drivers.
We also extend the "Direct IP" blacklist with with interfaces only
seen in "QMI" mode, assuming that these devices use the same
interface numbers for serial interfaces both in "Direct IP" and in
"QMI" mode.
Xi Wang [Mon, 9 Apr 2012 19:48:45 +0000 (15:48 -0400)]
usb: usbtest: avoid integer overflow in alloc_sglist()
A large `nents' from userspace could overflow the allocation size,
leading to memory corruption.
| alloc_sglist()
| usbtest_ioctl()
Use kmalloc_array() to avoid the overflow.
Signed-off-by: Xi Wang <xi.wang@gmail.com> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Xi Wang [Mon, 9 Apr 2012 19:48:55 +0000 (15:48 -0400)]
usb: usbtest: avoid integer overflow in test_ctrl_queue()
Avoid overflowing context.count = param->sglen * param->iterations,
where both `sglen' and `iterations' are from userspace.
| test_ctrl_queue()
| usbtest_ioctl()
Keep -EOPNOTSUPP for error code.
Signed-off-by: Xi Wang <xi.wang@gmail.com> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Alan Stern [Tue, 17 Apr 2012 19:22:39 +0000 (15:22 -0400)]
USB: fix deadlock in bConfigurationValue attribute method
This patch (as154) fixes a self-deadlock that occurs when userspace
writes to the bConfigurationValue sysfs attribute for a hub with
children. The task tries to lock the bandwidth_mutex at a time when
it already owns the lock:
The attribute's method calls usb_set_configuration(),
which calls usb_disable_device() with the bandwidth_mutex
held.
usb_disable_device() unregisters the existing interfaces,
which causes the hub driver to be unbound.
The hub_disconnect() routine calls hub_quiesce(), which
calls usb_disconnect() for each of the hub's children.
usb_disconnect() attempts to acquire the bandwidth_mutex
around a call to usb_disable_device().
The solution is to make usb_disable_device() acquire the mutex for
itself instead of requiring the caller to hold it. Then the mutex can
cover only the bandwidth deallocation operation and not the region
where the interfaces are unregistered.
This has the potential to change system behavior slightly when a
config change races with another config or altsetting change. Some of
the bandwidth released from the old config might get claimed by the
other config or altsetting, make it impossible to restore the old
config in case of a failure. But since we don't try to recover from
config-change failures anyway, this doesn't matter.
[This should be marked for stable kernels that contain the commit fccf4e86200b8f5edd9a65da26f150e32ba79808 "USB: Free bandwidth when
usb_disable_device is called."
That commit was marked for stable kernels as old as 2.6.32.]
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch makes it so that we identify FCoE rings earlier than
ixgbe_set_rx_buffer_len. Instead we identify the Rx FCoE rings at
allocation time in ixgbe_alloc_q_vector.
The motivation behind this change is to avoid memory corruption when FCoE
is enabled. Without this change we were initializing the rings at 0, and
2K on systems with 4K pages, then when we bumped the buffer size to 4K with
order 1 pages we were accessing offsets 2K and 6K instead of 0 and 4K.
This was resulting in memory corruptions.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Acked-by: Yi Zou <yi.zou@intel.com> Tested-by: Ross Brattain <ross.b.brattain@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Upon resume from standby, ixgbe may trigger the ASSERT_RTNL() in
netif_set_real_num_tx_queues(). The call stack is:
netif_set_real_num_tx_queues
ixgbe_set_num_queues
ixgbe_init_interrupt_scheme
ixgbe_resume
Signed-off-by: Benjamin Poirier <bpoirier@suse.de> Tested-by: Stephen Ko <stephen.s.ko@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
DMTIMER source selection on OMAP1 is broken. omap1_dm_timer_set_src()
tries to use __raw_{read,write}l() to read from and write to physical
addresses, but those functions take virtual addresses.
sparse caught this:
arch/arm/mach-omap1/timer.c:50:13: warning: incorrect type in argument 1 (different base types)
arch/arm/mach-omap1/timer.c:50:13: expected void const volatile [noderef] <asn:2>*<noident>
arch/arm/mach-omap1/timer.c:50:13: got unsigned int
arch/arm/mach-omap1/timer.c:52:9: warning: incorrect type in argument 1 (different base types)
arch/arm/mach-omap1/timer.c:52:9: expected void const volatile [noderef] <asn:2>*<noident>
arch/arm/mach-omap1/timer.c:52:9: got unsigned int
Fix by using omap_{read,writel}(), just like the other users of the
MOD_CONF_CTRL_1 register in the OMAP1 codebase. Of course, in the long term,
removing omap_{read,write}l() is the appropriate thing to do; but
this will take some work to do this cleanly.
Looks like this was caused by 97933d6 (ARM: OMAP1: dmtimer: conversion
to platform devices) that dangerously moved code and changed it in
the same patch.
Signed-off-by: Paul Walmsley <paul@pwsan.com> Cc: Tarun Kanti DebBarma <tarun.kanti@ti.com> Cc: stable@vger.kernel.org
[tony@atomide.com: updated comments to include the breaking commit] Signed-off-by: Tony Lindgren <tony@atomide.com>
Merge tag 'ext4_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4
Pull ext4 regression fixes from Ted Ts'o:
"This fixes a scalability problem reported by Andi Kleen and Tim Chen;
they were quite secretive about the precise nature of their workload,
but they later admitted that it only showed up when they were using a
large sparse file, so the amount of data I/O that was needed was close
to zero.
I'm not sure how realistic this is and it's only a regression if you
consider changes made since 2.6.39 to be a "regression" vis-a-vis the
policy regarding post-merge window bug fixes, but Linus agreed it was
worth fixing, so I'm including it in this pull request.
This also fixes the journalled quota mount options, which I
accidentally broke while I was cleaning up the mount option handling."
* tag 'ext4_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
ext4: fix handling of journalled quota options
ext4: address scalability issue by removing extent cache statistics
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull vfs fixes from Al Viro:
"A bunch of endianness fixes and a couple of nfsd error value fixes.
Speaking of endianness stuff, I'm rather tempted to slap
ccflags-y += -D__CHECK_ENDIAN__
in fs/Makefile, if not making it default for the entire tree; nfsd
regressions I've caught make one hell of a pile and we'd obviously
benefit from having that kind of stuff caught earlier..."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
lockd: fix the endianness bug
ocfs2: ->e_leaf_clusters endianness breakage
ocfs2: ->rl_count endianness breakage
ocfs: ->rl_used breakage on big-endian
ocfs2: ->l_next_free_req breakage on big-endian
btrfs: btrfs_root_readonly() broken on big-endian
ext4: fix endianness breakage in ext4_split_extent_at()
nfsd: fix compose_entry_fh() failure exits
nfsd: fix error value on allocation failure in nfsd4_decode_test_stateid()
nfsd: fix endianness breakage in TEST_STATEID handling
nfsd: fix error values returned by nfsd4_lockt() when nfsd_open() fails
nfsd: fix b0rken error value for setattr on read-only mount
ARM: OMAP: serial: Fix the ocp smart idlemode handling bug
The current serial UART code, while fidling with ocp idlemode bits,
forget about the smart idle wakeup bit even if it is supported by
UART IP block. This will lead to missing the module wakeup on OMAP's
where the smart idle wakeup is supported.
This was the root cause of the console sluggishness issue, I have been
observing on OMAP4 devices and also can be potential reason for some
other UART wakeup issues.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com> Acked-by: Kevin Hilman <khilman@ti.com> Acked-by: Govindraj.R <govindraj.raja@ti.com> Reviewed-by: Paul Walmsley <paul@pwsan.com> Cc: stable@vger.kernel.org Signed-off-by: Tony Lindgren <tony@atomide.com>
Assigning sequence number for frames without taking care
of the fragment field breaks transmission of fragmented frames.
Fix this by assigning the fragment number properly.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Mon, 16 Apr 2012 12:56:48 +0000 (14:56 +0200)]
mac80211: fix truncated packets in cooked monitor rx
Cooked monitor rx was recently changed to use ieee80211_add_rx_radiotap_header
instead of generating only limited radiotap information.
ieee80211_add_rx_radiotap_header assumes that FCS info is still present if
the hardware supports receiving it, however when cooked monitor rx packets
are processed, FCS info has already been stripped.
Fix this by adding an extra flag indicating FCS presence.
Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
ARM: OMAP2+: UART: Fix incorrect population of default uart pads
Commit (7496ba3 ARM: OMAP2+: UART: Add default mux for all uarts)
wrongly added muxing of default pads for all uarts. This causes
breakage on multiple boards using uart pins for alternate functions.
For example, on zoom3 random oopses can be seen with nfsroot as
the smsc911x ethernet FIFO timings on GPMC bus are controlled
by gpmc_wait2 and gpmc_wait3 pins. This means we can't mux these
pads to uart4 functionality as commit 7496ba3 was doing.
Not all boards tend to use all uarts and most of unused uart pins
are muxed for other purpose. This commit breaks the modules which
where trying to use unused uart pins on their boards.
So remove the default pad muxing. Note that this is not a complete
fix, as we now rely on bootloader set muxing for the uart wake-up
events. Further patching is needed to enable wake-up events for
uarts that are already muxed to uart mode.
Cc: Felipe Balbi <balbi@ti.com> Cc: Kevin Hilman <khilman@ti.com> Acked-by: Russ Dill <russ.dill@gmail.com> Reported-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Govindraj.R <govindraj.raja@ti.com>
[tony@atomide.com: updated comments to describe oops on zoom3] Signed-off-by: Tony Lindgren <tony@atomide.com>
Since we are using the m2p_override we do have struct pages
corresponding to the user vma mmap'ed by gntdev.
Removing the VM_PFNMAP flag makes get_user_pages work on that vma.
An example test case would be using a Xen userspace block backend
(QDISK) on a file on NFS using O_DIRECT.
ARM: OMAP: sram: fix BUG in dpll code for !PM case
_omap3_sram_configure_core_dpll is called when SDRC is reprogrammed,
which is done regardless of CONFIG_PM setting, so we always need it's
setup code too. Without this, we hit a BUG() on OMAP3 when kernel is
built without CONFIG_PM:
Reprogramming SDRC clock to 332000000 Hz
------------[ cut here ]------------
kernel BUG at arch/arm/plat-omap/sram.c:342!
Internal error: Oops - BUG: 0 [#1] ARM
...
[<c001c694>] (omap3_configure_core_dpll+0x68/0x6c) from [<c001b2dc>] (omap3_core_dpll_m2_set_rate+0x1)
[<c001b2dc>] (omap3_core_dpll_m2_set_rate+0x138/0x1b0) from [<c001a478>] (omap2_clk_set_rate+0x14/0x2)
[<c001a478>] (omap2_clk_set_rate+0x14/0x20) from [<c001c9dc>] (clk_set_rate+0x54/0x74)
[<c001c9dc>] (clk_set_rate+0x54/0x74) from [<c022b9c8>] (omap_sdrc_init+0x70/0x90)
[<c022b9c8>] (omap_sdrc_init+0x70/0x90) from [<c022f178>] (omap3pandora_init+0x11c/0x164)
[<c022f178>] (omap3pandora_init+0x11c/0x164) from [<c022849c>] (customize_machine+0x20/0x28)
[<c022849c>] (customize_machine+0x20/0x28) from [<c0225810>] (do_one_initcall+0xa0/0x16c)
[<c0225810>] (do_one_initcall+0xa0/0x16c) from [<c02259e0>] (kernel_init+0x104/0x1ac)
[<c02259e0>] (kernel_init+0x104/0x1ac) from [<c0009cec>] (kernel_thread_exit+0x0/0x8)
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Nicolas Ferre [Thu, 15 Mar 2012 10:31:58 +0000 (11:31 +0100)]
dmaengine: Kconfig: fix Atmel at_hdmac entry
Remove SoC dependency and make it generic for every Atmel ARM AT91. That will
allow to select this driver for newer chips. Keep dependency on AT91 because of
the use of an header file located in include/mach directory.
Modify the comment to reflect this.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com> Acked-by: Vinod Koul <vinod.koul@linux.intel.com>
Nicolas Ferre [Mon, 16 Apr 2012 08:58:12 +0000 (10:58 +0200)]
USB: gadget/at91_udc: add gpio_to_irq() function to vbus interrupt
Now that we are using irqdomains, we need to convert GPIO pins to Linux
IRQ numbers using the gpio_to_irq() function.
This call is added to request/free_irq calls.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com> Acked-by: Felipe Balbi <balbi@ti.com> Cc: linux-usb@vger.kernel.org
Nicolas Ferre [Fri, 6 Apr 2012 10:52:53 +0000 (12:52 +0200)]
leds-atmel-pwm.c: Make pwmled_probe() __devinit
Commit 892a884 (leds: convert led platform drivers to module_platform_driver)
is omitting the section mismatch error: so change annotation of the probe
function to __devinit instead of __init.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com> Cc: Richard Purdie <richard.purdie@linuxfoundation.org> Cc: Andrew Morton <akpm@linux-foundation.org>
m68knommu: make sure 2nd FEC eth interface pins are enabled on 5275 ColdFire
The CONFIG_FEC2 define was removed from the kernel many versions ago.
But it is still being used to set the multi-function pins when compiling
for a ColdFire 527[45] SoC that has 2 ethernet interfaces. Remove the
last remaining uses of this define, and so fix the setting of the pins
for the 2nd ethernet interface.
projects / linux-imx.git / log