Lokesh Vutla [Sat, 16 Mar 2013 06:16:48 +0000 (11:46 +0530)]
memory: emif: Load the correct custom config values from dt
of_get_property returns value in Big Endian format.
Before using this value it should be converted to little endian
using be32_to_cpup().
Custom configs of emif are read from dt using of_get_property,
but these are not converted to litte endian format.
Correcting the same here.
memory: emif: errata i743: Prohibit usage of Power-Down mode
ERRATA DESCRIPTION :
The EMIF supports power-down state for low power. The EMIF
automatically puts the SDRAM into power-down after the memory is
not accessed for a defined number of cycles and the
EMIF_PWR_MGMT_CTRL[10:8] REG_LP_MODE bit field is set to 0x4.
As the EMIF supports automatic output impedance calibration, a ZQ
calibration long command is issued every time it exits active
power-down and precharge power-down modes. The EMIF waits and
blocks any other command during this calibration.
The EMIF does not allow selective disabling of ZQ calibration upon
exit of power-down mode. Due to very short periods of power-down
cycles, ZQ calibration overhead creates bandwidth issues and
increases overall system power consumption. On the other hand,
issuing ZQ calibration long commands when exiting self-refresh is
still required.
WORKAROUND :
Because there is no power consumption benefit of the power-down due
to the calibration and there is a performance risk, the guideline
is to not allow power-down state and, therefore, to not have set
the EMIF_PWR_MGMT_CTRL[10:8] REG_LP_MODE bit field to 0x4.
This is applicable only for EMIF4D IP used in OMAP4 Soc's.
memory: emif: Fix the incorrect 'size' parameter in memcpy
The issue was that only the first timings table was added to the
emif platform data at the emif driver registration. All other
timings tables was filled with zeros. Now all emif timings table
are added to the platform data.
Nishanth Menon [Sat, 16 Mar 2013 06:16:45 +0000 (11:46 +0530)]
memory: emif: use restart if power_off not present when out of spec
Some machine or kernel variants might have missed implementation
of power off handlers. We DONOT want to let the system be in
"out of spec" state in this condition. So, WARN and attempt
a machine restart in the hopes of clearing the out-of-spec
temperature condition.
NOTE: This is not the safest option, but safer than leaving the
system in unstable conditions.
Nishanth Menon [Sat, 16 Mar 2013 06:16:44 +0000 (11:46 +0530)]
memory: emif: Handle devices which are not rated for >85C
As per JESD209-2E specification for LPDDR2,
http://www.jedec.org/standards-documents/results/jesd209-2E
Table 73, LPDDR2 memories come in two flavors - Standard and
Extended. The Standard types can operate from -25C to +85C
However, beyond that and upto +105C can only be supported by
Extended types.
Unfortunately, it seems there is no info in MR0(device info) or
MR[1,2](device feature) for run time detection of this capability
as far as seen on the spec. Hence, we provide a custom_config
flag to be populated by platforms which have these "extended"
type memories.
For the "Standard" memories, we need to consider MR4 notifications
of temperature triggers >85C as equivalent to thermal shutdown
events (equivalent to Spec specified thermal shutdown events for
"extended" parts).
Ambresh K [Sat, 16 Mar 2013 06:16:42 +0000 (11:46 +0530)]
memory: emif: setup LP settings on freq update
Program the power management shadow register on freq update
Else the concept of threshold frequencies dont really matter
as the system always uses the performance mode timing for LP
which is programmed in at init time.
Lokesh Vutla [Sat, 16 Mar 2013 06:16:41 +0000 (11:46 +0530)]
memory: emif: Fix the lpmode timeout calculation
The driver tries to round up the specified timeout cycles to
the next power of 2 value. This should be done defore updating
timeout variable.
Correcting this here.
David Brown [Tue, 12 Mar 2013 18:41:54 +0000 (11:41 -0700)]
SSBI: Remove MSM_ prefix from SSBI drivers
Although the SSBI sub is currently only used on MSM SoCs, it is still
a bus in its own right. Remove this msm_ prefix from the driver and
it's symbols. Clients can now refer directly to ssbi_write() and
ssbi_read().
Signed-off-by: David Brown <davidb@codeaurora.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
David Brown [Tue, 12 Mar 2013 18:41:52 +0000 (11:41 -0700)]
ssbi: Use regular init level
With device tree, and deferred probe, it is no longer necessary to
make sure that the ssbi bus driver is initialized very early. Restore
to a regular module_init().
Signed-off-by: David Brown <davidb@codeaurora.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
David Brown [Tue, 12 Mar 2013 18:41:51 +0000 (11:41 -0700)]
ssbi: Comment the use of udelay()
The ssbi driver uses a busywait loop to read its status register. Add
a comment explaining the timing of the device itself so that future
developers can better understand this delay, and possibly diagnose any
problems.
Signed-off-by: David Brown <davidb@codeaurora.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
David Brown [Tue, 12 Mar 2013 18:41:50 +0000 (11:41 -0700)]
SSBI: Convert SSBI to device tree
The SSBI bus is exclusive to the Qualcomm MSM targets, and all SoCs
using it will be using device tree. Convert this driver to indentify
with device tree.
This makes the bus probing a good bit simpler, since the attaching of
child nodes can be represented directly in the devicetree, rather than
having to be inferred by name.
Signed-off-by: David Brown <davidb@codeaurora.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
David Brown [Tue, 12 Mar 2013 18:41:49 +0000 (11:41 -0700)]
ssbi: Allow compilation as a module
The ssbi driver's read/write entry points are protected with wrappers
in the case when the driver isn't enabled. These wrappers don't make
any sense, since a client of the SSBI bus won't work without it. Make
these just regular functions, so that the SSBI driver can be built as
a module.
Signed-off-by: David Brown <davidb@codeaurora.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Kenneth Heitke [Tue, 12 Mar 2013 18:41:46 +0000 (11:41 -0700)]
add single-wire serial bus interface (SSBI) driver
SSBI is the Qualcomm single-wire serial bus interface used to connect
the MSM devices to the PMIC and other devices.
Since SSBI only supports a single slave, the driver gets the name of the
slave device passed in from the board file through the master device's
platform data.
SSBI registers pretty early (postcore), so that the PMIC can come up
before the board init. This is useful if the board init requires the
use of gpios that are connected through the PMIC.
Based on a patch by Dima Zavin <dima@android.com> that can be found at:
http://android.git.kernel.org/?p=kernel/msm.git;a=commitdiff;h=eb060bac4
This patch adds PMIC Arbiter support for the MSM8660. The PMIC Arbiter
is a hardware wrapper around the SSBI 2.0 controller that is designed to
overcome concurrency issues and security limitations. A controller_type
field is added to the platform data to specify the type of the SSBI
controller (1.0, 2.0, or PMIC Arbiter).
[davidb@codeaurora.org:
I've moved this driver into drivers/ssbi/ and added an include for
linux/module.h so that it will compile]
Signed-off-by: Kenneth Heitke <kheitke@codeaurora.org> Signed-off-by: David Brown <davidb@codeaurora.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Kurt Van Dijck [Mon, 18 Mar 2013 08:58:03 +0000 (09:58 +0100)]
FIX: softingcs conversion to module_pcmcia_driver macro
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by: Kurt Van Dijck <kurt.van.dijck@eia.be> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
pcmcia/ds.h: introduce helper for pcmcia_driver module boilerplate
Introduce the module_pcmcia_driver() macro which is a convenience macro
for pcmcia driver modules. It is intended to be used by pcmcia drivers
with init/exit sections that do nothing but register/unregister the
pcmcia driver.
Dan Carpenter [Fri, 1 Mar 2013 20:31:46 +0000 (23:31 +0300)]
applicom: use correct array offset
We're iterating through abps[] printing information, but here we
use the wrong array index. IndexCard comes from the user and in
this case it was specifically not range checked because we didn't
expect to use it.
K. Y. Srinivasan [Fri, 15 Mar 2013 19:30:06 +0000 (12:30 -0700)]
Drivers: hv: Add a new driver to support host initiated backup
This driver supports host initiated backup of the guest. On Windows guests,
the host can generate application consistent backups using the Windows VSS
framework. On Linux, we ensure that the backup will be file system consistent.
This driver allows the host to initiate a "Freeze" operation on all the mounted
file systems in the guest. Once the mounted file systems in the guest are frozen,
the host snapshots the guest's file systems. Once this is done, the guest's file
systems are "thawed".
This driver has a user-level component (daemon) that invokes the appropriate
operation on all the mounted file systems in response to the requests from
the host. The duration for which the guest is frozen is very short - a few seconds.
During this interval, the diff disk is comitted.
In this version of the patch I have addressed the feedback from Olaf Herring.
Also, some of the connector related issues have been fixed.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com> Cc: Evgeniy Polyakov <zbr@ioremap.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Properly cleanup the channel state on receipt of the "offer rescind" message.
Starting with ws2012, the host requires that the channel "relid" be properly
cleaned up when the offer is rescinded.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Implement the memory hot-add functionality. With this, Linux guests can fully
participate in the Dynamic Memory protocol implemented in the Windows hosts.
In this version of the patch, based Olaf Herring's feedback, I have gotten
rid of the module level dependency on MEMORY_HOTPLUG. Instead the code within
the driver that depends on MEMORY_HOTPLUG has the appropriate compilation
switches. This would allow this driver to support pure ballooning in cases
where the kernel does not support memory hotplug.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
K. Y. Srinivasan [Fri, 15 Mar 2013 19:25:42 +0000 (12:25 -0700)]
Drivers: hv: balloon: Make the balloon driver not unloadable
The balloon driver is stateful. For instance, it needs to keep track of pages
that have been ballooned out to properly post pressure reports. This state cannot
be re-constructed if the driver were to be unloaded and subsequently loaded.
Furthermore, as we support memory hot-add as part of this driver, this driver becomes
even more stateful and this state cannot be re-created. Make the balloon driver
unloadable to deal with this issue.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
K. Y. Srinivasan [Fri, 15 Mar 2013 19:25:41 +0000 (12:25 -0700)]
Drivers: hv: balloon: Execute hot-add code in a separate context
Execute the hot-add operation in a separate work context.
This allows us to decouple the pressure reporting activity from the
"hot-add" activity. Testing has shown that this makes the guest more
responsive to hot add requests.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
K. Y. Srinivasan [Fri, 15 Mar 2013 19:25:40 +0000 (12:25 -0700)]
Drivers: hv: balloon: Execute balloon inflation in a separate context
Execute the balloon inflation operation in a separate work context.
This allows us to decouple the pressure reporting activity from the
ballooning activity. Testing has shown that this decoupling makes the
guest more reponsive.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tomas Hozza [Wed, 13 Mar 2013 13:14:14 +0000 (14:14 +0100)]
tools: hv: daemon should check type of received Netlink msg
HyperV KVP daemon should check nlmsg_type in received netlink message
header. If message type is NLMSG_DONE daemon can proceed with processing
otherwise it should wait for next message.
Signed-off-by: Tomas Hozza <thozza@redhat.com> Acked-by: K. Y. Srinivasan <kys@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tomas Hozza [Wed, 13 Mar 2013 13:14:13 +0000 (14:14 +0100)]
tools: hv: daemon setsockopt should use options macros
HyperV daemon should use macros for option values when calling setsockopt.
Using specific numeric values instead of macros is confusing.
Signed-off-by: Tomas Hozza <thozza@redhat.com> Acked-by: K. Y. Srinivasan <kys@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tomas Hozza [Wed, 13 Mar 2013 13:14:12 +0000 (14:14 +0100)]
tools: hv: daemon should subscribe only to CN_KVP_IDX group
Previously HyperV daemon set sockaddr_nl.nl_groups to CN_KVP_IDX.
Netlink documentation says: "nl_groups is a bit mask with every bit
representing a netlink group number". Since CN_KVP_IDX value is "9"
HyperV daemon was receiving Netlink messages also from group number
"1" which is used by CGroup Rules Engine Daemon. This caused the
daemon to segfault (at least on 2.6.32 kernel).
HyperV daemon should set nl_groups to zero and specify multicast
group CN_KVP_IDX only by using socket options.
Signed-off-by: Tomas Hozza <thozza@redhat.com> Acked-by: K. Y. Srinivasan <kys@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Guenter Roeck [Wed, 27 Feb 2013 19:41:41 +0000 (11:41 -0800)]
misc/vmw_vmci: Add dependency on CONFIG_NET
Building the vmw_vmci driver with CONFIG_NET undefined results in:
drivers/built-in.o: In function `__qp_memcpy_from_queue.isra.13':
vmci_queue_pair.c:(.text+0x1671a8): undefined reference to `memcpy_toiovec'
drivers/built-in.o: In function `__qp_memcpy_to_queue.isra.14':
vmci_queue_pair.c:(.text+0x167341): undefined reference to `memcpy_fromiovec'
make[1]: [vmlinux] Error 1 (ignored)
since memcpy_toiovec and memcpy_fromiovec are defined in the networking code.
Add the missing dependency.
Tomas Winkler [Mon, 11 Mar 2013 16:27:02 +0000 (18:27 +0200)]
mei: revamp mei_data2slots
1. Move the mei_data2slots to mei_dev.h as it will be used
by the all supported HW.
2. Change return value from u8 to u32 to catch possible overflows
3. Eliminate computing the slots number twice in the same function
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Linus Torvalds [Sun, 10 Mar 2013 00:51:13 +0000 (16:51 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace
Pull namespace bugfixes from Eric Biederman:
"This is three simple fixes against 3.9-rc1. I have tested each of
these fixes and verified they work correctly.
The userns oops in key_change_session_keyring and the BUG_ON triggered
by proc_ns_follow_link were found by Dave Jones.
I am including the enhancement for mount to only trigger requests of
filesystem modules here instead of delaying this for the 3.10 merge
window because it is both trivial and the kind of change that tends to
bit-rot if left untouched for two months."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace:
proc: Use nd_jump_link in proc_ns_follow_link
fs: Limit sys_mount to only request filesystem modules (Part 2).
fs: Limit sys_mount to only request filesystem modules.
userns: Stop oopsing in key_change_session_keyring
Linus Torvalds [Sat, 9 Mar 2013 18:31:01 +0000 (10:31 -0800)]
Atmel MXT touchscreen: increase reset timeouts
There is a more complete atmel patch-series out by Nick Dyer that fixes
this and other things, but in the meantime this is the minimal thing to
get the touchscreen going on (at least my) Pixel Chromebook.
Not that I want my dirty fingers near that beautiful screen, but it
seems that a non-initialized touchscreen will also end up being a
constant wakeup source, so you have to disable it to go to sleep. And
it's easier to just fix the initialization sequence.
Update proc_ns_follow_link to use nd_jump_link instead of just
manually updating nd.path.dentry.
This fixes the BUG_ON(nd->inode != parent->d_inode) reported by Dave
Jones and reproduced trivially with mkdir /proc/self/ns/uts/a.
Sigh it looks like the VFS change to require use of nd_jump_link
happend while proc_ns_follow_link was baking and since the common case
of proc_ns_follow_link continued to work without problems the need for
making this change was overlooked.
Cc: stable@vger.kernel.org Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Linus Torvalds [Sat, 9 Mar 2013 01:33:20 +0000 (17:33 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs
Pull btrfs fixes from Chris Mason:
"These are scattered fixes and one performance improvement. The
biggest functional change is in how we throttle metadata changes. The
new code bumps our average file creation rate up by ~13% in fs_mark,
and lowers CPU usage.
Stefan bisected out a regression in our allocation code that made
balance loop on extents larger than 256MB."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
Btrfs: improve the delayed inode throttling
Btrfs: fix a mismerge in btrfs_balance()
Btrfs: enforce min_bytes parameter during extent allocation
Btrfs: allow running defrag in parallel to administrative tasks
Btrfs: avoid deadlock on transaction waiting list
Btrfs: do not BUG_ON on aborted situation
Btrfs: do not BUG_ON in prepare_to_reloc
Btrfs: free all recorded tree blocks on error
Btrfs: build up error handling for merge_reloc_roots
Btrfs: check for NULL pointer in updating reloc roots
Btrfs: fix unclosed transaction handler when the async transaction commitment fails
Btrfs: fix wrong handle at error path of create_snapshot() when the commit fails
Btrfs: use set_nlink if our i_nlink is 0
Benson Leung [Fri, 8 Mar 2013 03:43:34 +0000 (19:43 -0800)]
Platform: x86: chromeos_laptop : Add basic platform data for atmel devices
Add basic platform data to get the current upstream driver working
with the 224s touchpad and 1664s touchscreen.
We will be using NULL config so we will use the settings from the
devices' NVRAMs.
Daniel Kurtz [Fri, 8 Mar 2013 03:43:33 +0000 (19:43 -0800)]
Input: atmel_mxt_ts - Support for touchpad variant
This same driver can be used by atmel based touchscreens and touchpads
(buttonpads). Platform data may specify a device is a touchpad
using the is_tp flag.
This will cause the driver to perform some touchpad specific
initializations, such as:
* register input device name "Atmel maXTouch Touchpad" instead of
Touchscreen.
* register BTN_LEFT & BTN_TOOL_* event types.
* register axis resolution (as a fixed constant, for now)
* register BUTTONPAD property
* process GPIO buttons using reportid T19
Input event GPIO mapping is done by the platform data key_map array.
key_map[x] should contain the KEY or BTN code to send when processing
GPIOx from T19. To specify a GPIO as not an input source, populate
with KEY_RESERVED, or 0.
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org> Signed-off-by: Benson Leung <bleung@chromium.org> Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk> Tested-by: Olof Johansson <olof@lixom.net> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Fri, 8 Mar 2013 23:22:08 +0000 (15:22 -0800)]
Merge branch 'for-next' of git://git.samba.org/sfrench/cifs-2.6
Pull CIFS fixes from Steve French:
"A small set of cifs fixes which includes one for a recent regression
in the write path (pointed out by Anton), some fixes for rename
problems and as promised for 3.9 removing the obsolete sockopt mount
option (and the accompanying deprecation warning)."
* 'for-next' of git://git.samba.org/sfrench/cifs-2.6:
CIFS: Fix missing of oplock_read value in smb30_values structure
cifs: don't try to unlock pagecache page after releasing it
cifs: remove the sockopt= mount option
cifs: Check server capability before attempting silly rename
cifs: Fix bug when checking error condition in cifs_rename_pending_delete()
Linus Torvalds [Fri, 8 Mar 2013 23:05:42 +0000 (15:05 -0800)]
Merge branch 'akpm' (fixes from Andrew)
Merge misc fixes from Andrew Morton.
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
alpha: boot: fix build breakage introduced by system.h disintegration
memcg: initialize kmem-cache destroying work earlier
Randy has moved
ksm: fix m68k build: only NUMA needs pfn_to_nid
dmi_scan: fix missing check for _DMI_ signature in smbios_present()
Revert parts of "hlist: drop the node parameter from iterators"
idr: remove WARN_ON_ONCE() on negative IDs
mm/mempolicy.c: fix sp_node_init() argument ordering
mm/mempolicy.c: fix wrong sp_node insertion
ipc: don't allocate a copy larger than max
ipc: fix potential oops when src msg > 4k w/ MSG_COPY
Will Deacon [Fri, 8 Mar 2013 20:43:37 +0000 (12:43 -0800)]
alpha: boot: fix build breakage introduced by system.h disintegration
Commit ec2212088c42 ("Disintegrate asm/system.h for Alpha") removed the
system.h include from boot/head.S, which puts the PAL_* asm constants
out of scope.
Include <asm/pal.h> so we can get building again.
Signed-off-by: Will Deacon <will.deacon@arm.com> Cc: David Rusling <david.rusling@linaro.org> Cc: David Howells <dhowells@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
memcg: initialize kmem-cache destroying work earlier
Fix a warning from lockdep caused by calling cancel_work_sync() for
uninitialized struct work. This path has been triggered by destructon
kmem-cache hierarchy via destroying its root kmem-cache.
cache ffff88003c072d80
obj ffff88003b410000 cache ffff88003c072d80
obj ffff88003b924000 cache ffff88003c20bd40
INFO: trying to register non-static key.
the code is fine but needs lockdep annotation.
turning off the locking correctness validator.
Pid: 2825, comm: insmod Tainted: G O 3.9.0-rc1-next-20130307+ #611
Call Trace:
__lock_acquire+0x16a2/0x1cb0
lock_acquire+0x8a/0x120
flush_work+0x38/0x2a0
__cancel_work_timer+0x89/0xf0
cancel_work_sync+0xb/0x10
kmem_cache_destroy_memcg_children+0x81/0xb0
kmem_cache_destroy+0xf/0xe0
init_module+0xcb/0x1000 [kmem_test]
do_one_initcall+0x11a/0x170
load_module+0x19b0/0x2320
SyS_init_module+0xc6/0xf0
system_call_fastpath+0x16/0x1b
Hugh Dickins [Fri, 8 Mar 2013 20:43:34 +0000 (12:43 -0800)]
ksm: fix m68k build: only NUMA needs pfn_to_nid
A CONFIG_DISCONTIGMEM=y m68k config gave
mm/ksm.c: In function `get_kpfn_nid':
mm/ksm.c:492: error: implicit declaration of function `pfn_to_nid'
linux/mmzone.h declares it for CONFIG_SPARSEMEM and CONFIG_FLATMEM, but
expects the arch's asm/mmzone.h to declare it for CONFIG_DISCONTIGMEM
(see arch/mips/include/asm/mmzone.h for example).
Or perhaps it is only expected when CONFIG_NUMA=y: too much of a maze,
and m68k got away without it so far, so fix the build in mm/ksm.c.
Signed-off-by: Hugh Dickins <hughd@google.com> Reported-by: Geert Uytterhoeven <geert@linux-m68k.org> Cc: Petr Holasek <pholasek@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Ben Hutchings [Fri, 8 Mar 2013 20:43:32 +0000 (12:43 -0800)]
dmi_scan: fix missing check for _DMI_ signature in smbios_present()
Commit 9f9c9cbb6057 ("drivers/firmware/dmi_scan.c: fetch dmi version
from SMBIOS if it exists") hoisted the check for "_DMI_" into
dmi_scan_machine(), which means that we don't bother to check for
"_DMI_" at offset 16 in an SMBIOS entry. smbios_present() may also call
dmi_present() for an address where we found "_SM_", if it failed further
validation.
Check for "_DMI_" in smbios_present() before calling dmi_present().
[akpm@linux-foundation.org: fix build] Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Reported-by: Tim McGrath <tmhikaru@gmail.com> Tested-by: Tim Mcgrath <tmhikaru@gmail.com> Cc: Zhenzhong Duan <zhenzhong.duan@oracle.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Arnd Bergmann [Fri, 8 Mar 2013 20:43:31 +0000 (12:43 -0800)]
Revert parts of "hlist: drop the node parameter from iterators"
Commit b67bfe0d42ca ("hlist: drop the node parameter from iterators")
did a lot of nice changes but also contains two small hunks that seem to
have slipped in accidentally and have no apparent connection to the
intent of the patch.
This reverts the two extraneous changes.
Signed-off-by: Arnd Bergmann <arnd@arndb.de> Cc: Peter Senna Tschudin <peter.senna@gmail.com> Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Cc: Sasha Levin <sasha.levin@oracle.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Rusty Russell <rusty@rustcorp.com.au> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Tejun Heo [Fri, 8 Mar 2013 20:43:30 +0000 (12:43 -0800)]
idr: remove WARN_ON_ONCE() on negative IDs
idr_find(), idr_remove() and idr_replace() used to silently ignore the
sign bit and perform lookup with the rest of the bits. The weird behavior
has been changed such that negative IDs are treated as invalid. As the
behavior change was subtle, WARN_ON_ONCE() was added in the hope of
determining who's calling idr functions with negative IDs so that they can
be examined for problems.
Up until now, all two reported cases are ID number coming directly from
userland and getting fed into idr_find() and the warnings seem to cause
more problems than being helpful. Drop the WARN_ON_ONCE()s.
Peter Hurley [Fri, 8 Mar 2013 20:43:27 +0000 (12:43 -0800)]
ipc: don't allocate a copy larger than max
When MSG_COPY is set, a duplicate message must be allocated for the copy
before locking the queue. However, the copy could not be larger than was
sent which is limited to msg_ctlmax.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com> Acked-by: Stanislav Kinsbursky <skinsbursky@parallels.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Fri, 8 Mar 2013 22:46:04 +0000 (14:46 -0800)]
Merge branch 'stable' of git://git.kernel.org/pub/scm/linux/kernel/git/cmetcalf/linux-tile
Pull tile architecture fixes from Chris Metcalf:
"This fixes the bug that Al Viro spotted with the compat llseek code.
I also fixed the compat syscall definitions to use the new syscall
define macros to properly sign-extend their arguments."
* 'stable' of git://git.kernel.org/pub/scm/linux/kernel/git/cmetcalf/linux-tile:
tile: properly use COMPAT_SYSCALL_DEFINEx
tile: work around bug in the generic sys_llseek
Linus Torvalds [Fri, 8 Mar 2013 22:45:17 +0000 (14:45 -0800)]
Merge tag 'metag-for-v3.9-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/jhogan/metag
Pull metag bugfixes from James Hogan:
"A couple of fairly minor arch/metag integration fixes from v3.9-rc1:
- remove SET_PERSONALITY(): use default definition like other arches
now do.
- inhibit NUMA balancing: like SH, NUMA is used for memories with
different latencies. ARCH_WANT_VARIABLE_LOCALITY has been added
for this purpose."
* tag 'metag-for-v3.9-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/jhogan/metag:
metag: Inhibit NUMA balancing.
metag: remove SET_PERSONALITY()
Linus Torvalds [Fri, 8 Mar 2013 22:43:33 +0000 (14:43 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"All are boring small fixes in various parts:
- A few possible NULL-dereference or zero-division Oops fixes
- Fix vmaster slave volume notification
- Add codec ID for ALC233
- Various fixes in several ASoC WM codecs
- ASoC tegra i2c fix
Sorry if you wanted a thrilling adventure with huge sharks :)"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: ice1712: Initialize card->private_data properly
ALSA: hda - Add support of new codec ALC233
ALSA: hda/ca0132 - Avoid division by zero in dspxfr_one_seg()
ALSA: hda - check NULL pointer when creating SPDIF PCM switch
ALSA: hda - check NULL pointer when creating SPDIF controls
ASoC: wm5102: Apply a SYSCLK patch for later revs
ALSA: vmaster: Fix slave change notification
ASoC: tegra: fix I2S bit count mask
ALSA: seq: seq_oss_event: missing range checks
ASoC: wm8350: Use jiffies rather than msecs in schedule_delayed_work()
ASoC: wm5110: Correct OUT2/3 volume and switch names
ASoC: wm5102: Correct OUT2 volume and switch names
ASoC: wm8960: Fix ADC power bits
ASoC: wm8960: Correct register 0 and 1 defaults
Linus Torvalds [Fri, 8 Mar 2013 22:42:52 +0000 (14:42 -0800)]
Merge branch 'for-3.9/upstream-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid
Pull HID fix from Jiri Kosina:
"Bugfix for a long-standing bug in logitech-dj driver causing all sorts
of random initialization problems, finally debugged by Benjamin
Tissoires with help of Bob Bowles."
* 'for-3.9/upstream-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
HID: logitech-dj: do not directly call hid_output_raw_report() during probe
Linus Torvalds [Fri, 8 Mar 2013 17:03:07 +0000 (09:03 -0800)]
vfs: don't BUG_ON() if following a /proc fd pseudo-symlink results in a symlink
It's "normal" - it can happen if the file descriptor you followed was
opened with O_NOFOLLOW.
Reported-by: Dave Jones <davej@redhat.com> Cc: Al Viro <viro@zeniv.linux.org.uk> Cc: stable@kernel.org Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Thu, 7 Mar 2013 23:57:38 +0000 (15:57 -0800)]
Merge branch 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Peter Anvin:
"Several boot fixes (MacBook, legacy EFI bootloaders), another
please-don't-brick fix, and some minor stuff."
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86: Do not try to sync identity map for non-mapped pages
x86, doc: Be explicit about what the x86 struct boot_params requires
x86: Don't clear efi_info even if the sentinel hits
x86, mm: Make sure to find a 2M free block for the first mapped area
x86: Fix 32-bit *_cpu_data initializers
efivarfs: return accurate error code in efivarfs_fill_super()
efivars: efivarfs_valid_name() should handle pstore syntax
efi: be more paranoid about available space when creating variables
iommu, x86: Add DMA remap fault reason
x86, smpboot: Remove unused variable
Linus Torvalds [Thu, 7 Mar 2013 22:55:54 +0000 (14:55 -0800)]
Merge branch 'drm-fixes' of git://people.freedesktop.org/~airlied/linux
Pull drm fixes from Dave Airlie:
"Misc radeon, nouveau, mgag200 and intel fixes.
The intel fixes should contain the fix for the touchpad on the
Chromebook - hey I'm an input maintainer now!"
Hate to pee on your parade, Dave, but I don't think being an input
maintainer is necessarily something to strive for..
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux: (25 commits)
drm/tegra: drop "select DRM_HDMI"
drm: Documentation typo fixes
drm/mgag200: Bug fix: Renesas board now selects native resolution.
drm/mgag200: Reject modes that are too big for VRAM
drm/mgag200: 'fbdev_list' in 'struct mga_fbdev' is not used
drm/radeon: don't check mipmap alignment if MIP_ADDRESS is FMASK
drm/radeon: skip MC reset as it's probably not hung
drm/radeon: add primary dac adj quirk for R200 board
drm/radeon: don't set hpd, afmt interrupts when interrupts are disabled
drm/i915: Turn off hsync and vsync on ADPA when disabling crt
drm/i915: Fix incorrect definition of ADPA HSYNC and VSYNC bits
drm/i915: also disable south interrupts when handling them
drm/i915: enable irqs earlier when resuming
drm/i915: Increase the RC6p threshold.
DRM/i915: On G45 enable cursor plane briefly after enabling the display plane.
drm/nv50-: prevent some races between modesetting and page flipping
drm/nouveau/i2c: drop parent refcount when creating ports
drm/nv84: fix regression in page flipping
drm/nouveau: Fix typo in init_idx_addr_latched().
drm/nouveau: Disable AGP on PowerPC again.
...
Linus Torvalds [Thu, 7 Mar 2013 22:54:28 +0000 (14:54 -0800)]
Merge tag 'pm+acpi-3.9-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management fixes from Rafael J Wysocki:
- Two fixes for the new intel_pstate driver from Dirk Brandewie.
- Fix for incorrect usage of the .find_bridge() callback from struct
acpi_bus_type in the USB core and subsequent removal of that callback
from Rafael J Wysocki.
- ACPI processor driver cleanups from Chen Gang and Syam Sidhardhan.
- ACPI initialization and error messages fix from Joe Perches.
- Operating Performance Points documentation improvement from Nishanth
Menon.
- Fixes for memory leaks and potential concurrency issues and sysfs
attributes leaks during device removal in the core device PM QoS code
from Rafael J Wysocki.
- Calxeda Highbank cpufreq driver simplification from Emilio López.
- cpufreq comment cleanup from Namhyung Kim.
- Fix for a section mismatch in Calxeda Highbank interprocessor
communication code from Mark Langsdorf (this is not a PM fix strictly
speaking, but the code in question went in through the PM tree).
* tag 'pm+acpi-3.9-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
cpufreq / intel_pstate: Do not load on VM that does not report max P state.
cpufreq / intel_pstate: Fix intel_pstate_init() error path
ACPI / glue: Drop .find_bridge() callback from struct acpi_bus_type
ACPI / glue: Add .match() callback to struct acpi_bus_type
ACPI / porocessor: Beautify code, pr->id is u32 which is never < 0
ACPI / processor: Remove redundant NULL check before kfree
ACPI / Sleep: Avoid interleaved message on errors
PM / QoS: Remove device PM QoS sysfs attributes at the right place
PM / QoS: Fix concurrency issues and memory leaks in device PM QoS
cpufreq: highbank: do not initialize array with a loop
PM / OPP: improve introductory documentation
cpufreq: Fix a typo in comment
mailbox, pl320-ipc: remove __init from probe function
Paul Bolle [Tue, 5 Mar 2013 21:07:36 +0000 (22:07 +0100)]
drm/tegra: drop "select DRM_HDMI"
Commit ac24c2204a76e5b42aa103bf963ae0eda1b827f3 ("drm/tegra: Use generic
HDMI infoframe helpers") added "select DRM_HDMI" to the DRM_TEGRA
Kconfig entry. But there is no Kconfig symbol named DRM_HDMI. The select
statement for that symbol is a nop. Drop it.
What was needed to use HDMI functionality was to select HDMI (which this
entry already did through depending on DRM) and to include linux/hdmi.h
(which this commit also did).
Signed-off-by: Paul Bolle <pebolle@tiscali.nl> Acked-by: Thierry Reding <thierry.reding@avionic-design.de> Signed-off-by: Dave Airlie <airlied@redhat.com>
Julia Lemire [Thu, 7 Mar 2013 15:41:03 +0000 (10:41 -0500)]
drm/mgag200: Bug fix: Renesas board now selects native resolution.
Renesas boards were consistently defaulting to the 1024x768 resolution,
regardless of the native resolution of the monitor plugged in. It was
determined that the EDID of the monitor was not being read. Since the
DAC is a shared line, in order to read from or write to it we must take
control of the DAC clock. This can be done by setting the proper
register to one.
This bug fix sets the register MGA1064_GEN_IO_CTL2 to one. The DAC
control line can be used to determine whether or not a new monitor has
been plugged in. But since the hotplug feature is not one we will
support, it has been decided to simply leave the register set to one.
Signed-off-by: Julia Lemire <jlemire@matrox.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
drm/mgag200: Reject modes that are too big for VRAM
A monitor or a user could request a resolution greater than the
available VRAM for the backing framebuffer. This change checks the
required framebuffer size against the max VRAM size and rejects modes
if they are too big. This change can also remove a mode request passed
in via the video= parameter.
Signed-off-by: Christopher Harvey <charvey@matrox.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
Dave Airlie [Thu, 7 Mar 2013 22:28:22 +0000 (08:28 +1000)]
Merge branch 'drm-fixes-3.9' of git://people.freedesktop.org/~agd5f/linux into drm-next
Alex writes:
Radeon fixes pull. Not much to it.
- fix some splatter if the interrupt handler isn't registered
- Add a quirk for an old R200 board to fix washed out colors on the DAC
- Don't try and soft reset the MC when we reset the GPU. It usually doesn't
need it and doesn't always work reliably.
- A CS checker fix from Marek
* 'drm-fixes-3.9' of git://people.freedesktop.org/~agd5f/linux:
drm/radeon: don't check mipmap alignment if MIP_ADDRESS is FMASK
drm/radeon: skip MC reset as it's probably not hung
drm/radeon: add primary dac adj quirk for R200 board
drm/radeon: don't set hpd, afmt interrupts when interrupts are disabled
projects / linux-imx.git / log