* Routines for control of MPU-401 in UART mode
*
* MPU-401 supports UART mode which is not capable generate transmit
- * interrupts thus output is done via polling. Also, if irq < 0, then
+ * interrupts thus output is done via polling. Without interrupt,
* input is done also via polling. Do not expect good performance.
*
*
*/
-#define snd_mpu401_input_avail(mpu) (!(mpu->read(mpu, MPU401C(mpu)) & 0x80))
-#define snd_mpu401_output_ready(mpu) (!(mpu->read(mpu, MPU401C(mpu)) & 0x40))
-
-#define MPU401_RESET 0xff
-#define MPU401_ENTER_UART 0x3f
-#define MPU401_ACK 0xfe
+#define snd_mpu401_input_avail(mpu) \
+ (!(mpu->read(mpu, MPU401C(mpu)) & MPU401_RX_EMPTY))
+#define snd_mpu401_output_ready(mpu) \
+ (!(mpu->read(mpu, MPU401C(mpu)) & MPU401_TX_FULL))
/* Build in lowlevel io */
static void mpu401_write_port(struct snd_mpu401 *mpu, unsigned char data,
#endif
}
mpu->write(mpu, cmd, MPU401C(mpu));
- if (ack) {
+ if (ack && !(mpu->info_flags & MPU401_INFO_NO_ACK)) {
ok = 0;
timeout = 10000;
while (!ok && timeout-- > 0) {
/* first time - flush FIFO */
while (max-- > 0)
mpu->read(mpu, MPU401D(mpu));
- if (mpu->irq < 0)
+ if (mpu->info_flags & MPU401_INFO_USE_TIMER)
snd_mpu401_uart_add_timer(mpu, 1);
}
snd_mpu401_uart_input_read(mpu);
spin_unlock_irqrestore(&mpu->input_lock, flags);
} else {
- if (mpu->irq < 0)
+ if (mpu->info_flags & MPU401_INFO_USE_TIMER)
snd_mpu401_uart_remove_timer(mpu, 1);
clear_bit(MPU401_MODE_BIT_INPUT_TRIGGER, &mpu->mode);
}
static void snd_mpu401_uart_output_write(struct snd_mpu401 * mpu)
{
unsigned char byte;
- int max = 256, timeout;
+ int max = 256;
do {
if (snd_rawmidi_transmit_peek(mpu->substream_output,
&byte, 1) == 1) {
- for (timeout = 100; timeout > 0; timeout--) {
- if (snd_mpu401_output_ready(mpu))
- break;
- }
- if (timeout == 0)
+ /*
+ * Try twice because there is hardware that insists on
+ * setting the output busy bit after each write.
+ */
+ if (!snd_mpu401_output_ready(mpu) &&
+ !snd_mpu401_output_ready(mpu))
break; /* Tx FIFO full - try again later */
mpu->write(mpu, byte, MPU401D(mpu));
snd_rawmidi_transmit_ack(mpu->substream_output, 1);
static void snd_mpu401_uart_free(struct snd_rawmidi *rmidi)
{
struct snd_mpu401 *mpu = rmidi->private_data;
- if (mpu->irq_flags && mpu->irq >= 0)
+ if (mpu->irq >= 0)
free_irq(mpu->irq, (void *) mpu);
release_and_free_resource(mpu->res);
kfree(mpu);
* @hardware: the hardware type, MPU401_HW_XXXX
* @port: the base address of MPU401 port
* @info_flags: bitflags MPU401_INFO_XXX
- * @irq: the irq number, -1 if no interrupt for mpu
- * @irq_flags: the irq request flags (SA_XXX), 0 if irq was already reserved.
+ * @irq: the ISA irq number, -1 if not to be allocated
* @rrawmidi: the pointer to store the new rawmidi instance
*
* Creates a new MPU-401 instance.
unsigned short hardware,
unsigned long port,
unsigned int info_flags,
- int irq, int irq_flags,
+ int irq,
struct snd_rawmidi ** rrawmidi)
{
struct snd_mpu401 *mpu;
mpu->cport = port + 2;
else
mpu->cport = port + 1;
- if (irq >= 0 && irq_flags) {
- if (request_irq(irq, snd_mpu401_uart_interrupt, irq_flags,
+ if (irq >= 0) {
+ if (request_irq(irq, snd_mpu401_uart_interrupt, IRQF_DISABLED,
"MPU401 UART", (void *) mpu)) {
snd_printk(KERN_ERR "mpu401_uart: "
"unable to grab IRQ %d\n", irq);
return -EBUSY;
}
}
+ if (irq < 0 && !(info_flags & MPU401_INFO_IRQ_HOOK))
+ info_flags |= MPU401_INFO_USE_TIMER;
mpu->info_flags = info_flags;
mpu->irq = irq;
- mpu->irq_flags = irq_flags;
if (card->shortname[0])
snprintf(rmidi->name, sizeof(rmidi->name), "%s MIDI",
card->shortname);