2 -- * Raspberry Pi BLDC/PMSM motor control design for RPi-MI-1 board *
3 -- The toplevel component file
5 -- (c) 2015 Martin Prudek <prudemar@fel.cvut.cz>
6 -- Czech Technical University in Prague
8 -- Project supervision and original project idea
9 -- idea by Pavel Pisa <pisa@cmp.felk.cvut.cz>
11 -- Related RPi-MI-1 hardware is designed by Petr Porazil,
12 -- PiKRON Ltd <http://www.pikron.com>
14 -- VHDL design reuses some components and concepts from
15 -- LXPWR motion power stage board and LX_RoCoN system
16 -- developed at PiKRON Ltd with base code implemented
17 -- by Marek Peca <hefaistos@gmail.com>
19 -- license: GNU LGPL and GPLv3+
23 use ieee.std_logic_1164.all;
24 use ieee.numeric_std.all;
27 entity rpi_pmsm_control is
29 pwm_width : natural:=11
32 gpio2: in std_logic; -- SDA
33 gpio3: in std_logic; -- SCL
34 gpio4: in std_logic; -- CLK
35 gpio14: in std_logic; -- Tx
36 gpio15: in std_logic; -- Rx
37 gpio17: in std_logic; -- RTS
38 gpio18: in std_logic; -- PWM0/PCMCLK
39 gpio27: in std_logic; -- SD1DAT3
40 gpio22: in std_logic; -- SD1CLK
41 gpio23: in std_logic; -- SD1CMD
42 gpio24: in std_logic; -- SD1DAT0
43 gpio10: in std_logic; -- SPI0MOSI
44 gpio9: out std_logic; -- SPI0MISO
45 gpio25: in std_logic; -- SD1DAT1
46 gpio11: in std_logic; -- SPI0SCLK
47 gpio8: in std_logic; -- SPI0CE0
48 gpio7: in std_logic; -- SPI0CE1
49 gpio5: in std_logic; -- GPCLK1
50 gpio6: in std_logic; -- GPCLK2
51 gpio12: in std_logic; -- PWM0
52 gpio13: in std_logic; -- PWM1
53 gpio19: in std_logic; -- PWM1/SPI1MISO/PCMFS
54 gpio16: in std_logic; -- SPI1CE2
55 gpio26: in std_logic; -- SD1DAT2
56 gpio20: in std_logic; -- SPI1MOSI/PCMDIN/GPCLK0
57 gpio21: in std_logic; -- SPI1SCLK/PCMDOUT/GPCLK1
60 -- Each PWM signal has cooresponding shutdown
61 pwm: out std_logic_vector (1 to 3);
62 shdn: out std_logic_vector (1 to 3);
63 -- Fault/power stage status
64 stat: in std_logic_vector (1 to 3);
66 hal_in: in std_logic_vector (1 to 3);
72 power_stat: in std_logic;
74 adc_miso: in std_logic;
75 adc_mosi: out std_logic;
76 adc_sclk: out std_logic;
77 adc_scs: out std_logic;
79 ext_miso: in std_logic; --master in slave out
80 ext_mosi: in std_logic; --master out slave in
81 ext_sclk: in std_logic;
82 ext_scs0: in std_logic;
83 ext_scs1: in std_logic;
84 ext_scs2: in std_logic;
86 rs485_rxd: in std_logic;
87 rs485_txd: out std_logic;
88 rs485_dir: out std_logic;
93 dip_sw: in std_logic_vector (1 to 3); --na desce je prohozene cislovanni
94 -- Unused terminal to keep design tools silent
95 dummy_unused : out std_logic
100 architecture behavioral of rpi_pmsm_control is
101 attribute syn_noprune :boolean;
102 attribute syn_preserve :boolean;
103 attribute syn_keep :boolean;
104 attribute syn_hier :boolean;
109 powerdown, clka: in std_logic;
110 lock, gla: out std_logic
115 port (A: in std_logic; Y: out std_logic);
122 a0, b0: in std_logic;
123 qcount: out std_logic_vector (31 downto 0);
124 a_rise, a_fall, b_rise, b_fall, ab_event: out std_logic;
125 ab_error: out std_logic
135 sync: in std_logic; --flag that counter "restarts-overflows"
136 data_valid:in std_logic; --indicates data is consistent
137 failsafe: in std_logic; --turn off both transistors
138 en_p, en_n: in std_logic; --enable positive & enable shutdown
139 match: in std_logic_vector (pwm_width-1 downto 0); --posion of counter when we swap output logic
140 count: in std_logic_vector (pwm_width-1 downto 0); --we use an external counter
141 out_p, out_n: out std_logic --pwm outputs: positive & shutdown
142 --TODO add the rest of pwm signals, swap match to pwm_word
146 --frequency division by 12
149 clk_in: in std_logic;
154 component adc_reader is
156 clk: in std_logic; --input clk
157 divided_clk : in std_logic; --divided clk - value suitable to sourcing voltage
158 adc_reset: in std_logic;
159 adc_miso: in std_logic; --spi master in slave out
160 adc_channels: out std_logic_vector (35 downto 0); --consistent data of 3 channels
161 adc_sclk: out std_logic; --spi clk
162 adc_scs: out std_logic; --spi slave select
163 adc_mosi: out std_logic; --spi master out slave in
164 measur_count: out std_logic_vector(8 downto 0) --number of accumulated measurments
170 signal adc_reset : std_logic;
171 signal adc_channels: std_logic_vector(71 downto 0);
172 signal adc_m_count: std_logic_vector(8 downto 0);
174 --clock signals for logic and master fail monitoring
175 signal gpio_clk: std_logic;
176 signal pll_clkin, pll_clkout, pll_lock: std_logic;
177 signal clkmon_dly1, clkmon_dly2: std_logic;
178 signal clkmon_fail, clkmon_fail_next: std_logic;
179 signal clkmon_wdg: integer range 0 to 6;
180 signal reset_sync, reset_async: std_logic;
181 signal failsafe, next_failsafe: std_logic;
183 --RPi SPI interface signals named aliases
184 signal spi_clk, spi_ce, spi_mosi, spi_miso : std_logic;
185 signal spiclk_old: std_logic_vector(1 downto 0); --pro detekci hrany SPI hodin
187 --signal pwm_in, pwm_dir_in: std_logic;
188 signal dat_reg : STD_LOGIC_VECTOR (127 downto 0); --shift register for spi
189 signal position: std_logic_vector(31 downto 0); --pozice z qcounteru
190 signal index_position: std_logic_vector(11 downto 0); --pozice irc_i
191 signal ce0_old: std_logic_vector(1 downto 0);
194 constant pwm_n: natural := 3; --number of pwm outputs
195 --number of ticks per pwm cycle, 2^11=2048
196 constant pwm_period : std_logic_vector (pwm_width-1 downto 0) := (others=>'1');
197 type pwm_res_type is array(1 to 3) of std_logic_vector (pwm_width-1 downto 0);
199 signal pwm_match: pwm_res_type; --point of reversion of pwm output, 0 to 2047
200 signal pwm_count: std_logic_vector (pwm_width-1 downto 0); --counter, 0 to 2047
201 signal pwm_sync: std_logic;
202 signal pwm_en_p: std_logic_vector(1 to 3);
203 signal pwm_en_n: std_logic_vector(1 to 3);
204 signal pwm_sig: std_logic_vector(1 to 3);
206 signal income_data_valid: std_logic;
208 signal clk_4M17: std_logic;
210 -- irc signals processing
211 signal irc_i_prev: std_logic;
213 -- attribute syn_noprune of gpio2 : signal is true;
214 -- attribute syn_preserve of gpio2 : signal is true;
215 -- attribute syn_keep of gpio2 : signal is true;
216 -- attribute syn_hier of gpio2 : signal is true;
219 -- PLL as a reset generator
221 --zesileni signalu GPIO CLK
235 -- the failasfe signal from communication block if CRC is used
236 next_failsafe <= '0';
238 reset_async <= not pll_lock or clkmon_fail;
240 pll_clkin <= gpio_clk;
257 pwm_block: for i in pwm_n downto 1 generate
260 pwm_width => pwm_width
263 clock => gpio_clk, --50 Mhz clk from gpclk on raspberry
264 sync => pwm_sync, --counter restarts
265 data_valid => income_data_valid,
266 failsafe => failsafe,
268 -- pwm config bits & match word
270 en_n => pwm_en_n(i), --enable positive pwm
271 en_p => pwm_en_p(i), --enable "negative" ->activate shutdown
272 match => pwm_match(i),
275 out_p => pwm_sig(i), --positive signal
276 out_n => shdn(i) --reverse signal is in shutdown mode
283 --reset => income_data_valid,
288 -- ADC needs 3.2 MHz clk when powered from +5V Vcc
289 -- 2.0 MHz clk when +2.7V Vcc
290 -- on the input is 4.17Mhz,but this frequency is divided inside adc_reader by 2 to 2.08 Mhz,
291 -- while we use +3.3V Vcc
292 adc_reader_map: adc_reader
295 divided_clk => clk_4M17,
296 adc_reset => adc_reset,
297 adc_miso => adc_miso,
298 adc_channels => adc_channels,
299 adc_sclk => adc_sclk,
301 adc_mosi => adc_mosi,
302 measur_count => adc_m_count
306 dummy_unused <= gpio2 and gpio3 and
308 gpio12 and gpio13 and gpio14 and
309 gpio15 and gpio16 and gpio19 and
310 gpio20 and gpio21 and gpio26 and
311 stat(1) and stat(2) and stat(3) and
312 hal_in(1) and hal_in(2) and hal_in(3) and
313 irc_i and power_stat and
316 can_rx and can_tx and
317 dip_sw(1) and dip_sw(2) and dip_sw(3) and
319 gpio17 and gpio18 and gpio27 and gpio22 and gpio23 and gpio24 and gpio25 and
321 ext_scs1 and ext_scs2 and ext_miso and ext_mosi and ext_sclk and ext_scs0;
331 pwm(1) <= pwm_sig(1) and dip_sw(1);
332 pwm(2) <= pwm_sig(2) and dip_sw(2);
333 pwm(3) <= pwm_sig(3) and dip_sw(3);
338 wait until (gpio_clk'event and gpio_clk='1');
339 if irc_i_prev = '0' and irc_i = '1' then
340 index_position(11 downto 0)<=position(11 downto 0);
347 wait until (gpio_clk'event and gpio_clk='1');
348 IF(pwm_count = pwm_period) THEN
349 --end of period reached
350 pwm_count <= (others=>'0'); --reset counter
351 pwm_sync <= '1'; -- inform PWM logic about new period start
352 ELSE --end of period not reached
353 pwm_count <= std_logic_vector(unsigned(pwm_count)+1); --increment counter
360 --position is obtained on rising edge -> we should write it on next cycle
361 wait until (gpio_clk'event and gpio_clk='1');
363 --SCLK edge detection
364 spiclk_old(0)<=spi_clk;
365 spiclk_old(1)<=spiclk_old(0);
369 ce0_old(1)<=ce0_old(0);
371 if (spiclk_old="01") then --rising edge, faze cteni
372 if (spi_ce = '0') then -- SPI CS must be selected
373 -- shift serial data into dat_reg on each rising edge
375 dat_reg(127 downto 0) <= dat_reg(126 downto 0) & spi_mosi;
377 elsif (spiclk_old="10" ) then --falling edge, faze zapisu
378 if (spi_ce = '0') then
379 spi_miso <= dat_reg(127); --zapisujeme nejdriv MSB
384 --sestupna hrana SS, pripravime data pro prenos
385 if (ce0_old = "10" ) then
386 income_data_valid<='0';
387 dat_reg(127 downto 96) <= position(31 downto 0); --pozice
388 dat_reg(95 downto 93) <= hal_in(1 to 3); --halovy sondy
389 dat_reg(92 downto 81) <= index_position(11 downto 0); --position of irc_i
390 dat_reg(80 downto 72) <=adc_m_count(8 downto 0); --count of measurments
391 --data order schould be: ch2 downto ch0 downto ch1
392 dat_reg(71 downto 0) <= adc_channels(71 downto 0); --current mesurments
393 spi_miso <= position(31); --prepare the first bit on SE activation
394 adc_reset<='0'; --remove reset flag, and wait on its rising edge
395 elsif (ce0_old = "01") then --rising edge of SS, we should read the data
397 pwm_en_p(1 to 3)<=dat_reg(126 downto 124);
398 pwm_en_n(1 to 3)<=dat_reg(123 downto 121);
399 --11 bit pwm TODO: make it generic
400 pwm_match(1)(pwm_width-1 downto 0)<=dat_reg(66 downto 56);
401 pwm_match(2)(pwm_width-1 downto 0)<=dat_reg(55 downto 45);
403 pwm_match(3)(pwm_width-1 downto 0)<=dat_reg(42 downto 32);
404 income_data_valid<='1';
408 clock_monitor: process (pll_clkout, gpio_clk, clkmon_dly1, clkmon_wdg, clkmon_fail_next)
410 if pll_clkout'event and pll_clkout = '1' then
411 clkmon_dly1 <= gpio_clk;
412 clkmon_dly2 <= clkmon_dly1;
413 if clkmon_dly1 = '0' and clkmon_dly2 = '1' then
415 clkmon_fail_next <= '0';
416 elsif clkmon_wdg > 0 then
417 clkmon_wdg <= clkmon_wdg - 1;
418 clkmon_fail_next <= '0';
421 clkmon_fail_next <= '1';
423 clkmon_fail <= clkmon_fail_next;
427 async_rst: process (gpio_clk, reset_async, reset_sync)
429 if reset_async = '1' then
431 elsif gpio_clk'event and gpio_clk = '1' then
432 failsafe <= next_failsafe or reset_sync;
436 sync_rst: process (gpio_clk, reset_async)
438 if gpio_clk'event and gpio_clk = '1' then
439 reset_sync <= reset_async;