LinCAN sources go through big white-space cleanup.

[lincan.git] / lincan / src / pcm3680.c

diff --git a/lincan/src/pcm3680.c b/lincan/src/pcm3680.c
index 4175f1bb3942e92016908e59a54ccf07c3b85446..810b981484ccb2bef645d84321f85b6b16c0f7ea 100644 (file)
--- a/lincan/src/pcm3680.c
+++ b/lincan/src/pcm3680.c
@@ -52,7 +52,7 @@
  *
  * The function template_request_io() is used to reserve the io-memory. If your
  * hardware uses a dedicated memory range as hardware control registers you
- * will have to add the code to reserve this memory as well. 
+ * will have to add the code to reserve this memory as well.
  * %IO_RANGE is the io-memory range that gets reserved, please adjust according
  * your hardware. Example: #define IO_RANGE 0x100 for i82527 chips or
  * #define IO_RANGE 0x20 for sja1000 chips in basic CAN mode.
@@ -70,7 +70,7 @@ int pcm3680_request_io(struct candevice_t *candev)
                CANMSG("Unable to access I/O memory at: 0x%lx\n", candev->io_addr);
                can_release_mem_region(candev->io_addr,IO_RANGE);
                return -ENODEV;
-       
+
        }
        can_base_addr_fixup(candev, remap_addr);
        DEBUGMSG("Registered IO-memory: 0x%lx - 0x%lx\n", candev->io_addr, candev->io_addr + IO_RANGE - 1);
@@ -100,8 +100,8 @@ int pcm3680_release_io(struct candevice_t *candev)
  * template_reset - hardware reset routine
  * @candev: Pointer to candevice/board structure
  *
- * The function template_reset() is used to give a hardware reset. This is 
- * rather hardware specific so I haven't included example code. Don't forget to 
+ * The function template_reset() is used to give a hardware reset. This is
+ * rather hardware specific so I haven't included example code. Don't forget to
  * check the reset status of the chip before returning.
  * Return Value: The function returns zero on success or %-ENODEV on failure
  * File: src/template.c
@@ -111,7 +111,7 @@ int pcm3680_reset(struct candevice_t *candev)
        int i=0;
        struct canchip_t *chip;
        int chipnr;
-       
+
        DEBUGMSG("Resetting pcm3680 hardware ...\n");
        for(chipnr=0;chipnr<candev->nr_sja1000_chips;chipnr++) {
                chip=candev->chip[chipnr];
@@ -153,7 +153,7 @@ int pcm3680_reset(struct candevice_t *candev)
  * Return Value: The function always returns zero
  * File: src/template.c
  */
-int pcm3680_init_hw_data(struct candevice_t *candev) 
+int pcm3680_init_hw_data(struct candevice_t *candev)
 {
        candev->res_addr=RESET_ADDR;
        candev->nr_82527_chips=NR_82527;
@@ -187,7 +187,7 @@ int pcm3680_init_hw_data(struct candevice_t *candev)
  * The entry @int_clk_reg holds hardware specific options for the Clock Out
  * register. Options defined in the %i82527.h file:
  * %iCLK_CD0, %iCLK_CD1, %iCLK_CD2, %iCLK_CD3, %iCLK_SL0, %iCLK_SL1.
- * The entry @int_bus_reg holds hardware specific options for the Bus 
+ * The entry @int_bus_reg holds hardware specific options for the Bus
  * Configuration register. Options defined in the %i82527.h file:
  * %iBUS_DR0, %iBUS_DR1, %iBUS_DT1, %iBUS_POL, %iBUS_CBY.
  * Return Value: The function always returns zero
@@ -218,7 +218,7 @@ int pcm3680_init_chip_data(struct candevice_t *candev, int chipnr)
  * CAN chip. In case of the sja1000 there's only one message object but on the
  * i82527 chip there are 15.
  * The code below is for a i82527 chip and initializes the object base addresses
- * The entry @obj_base_addr represents the first memory address of the message 
+ * The entry @obj_base_addr represents the first memory address of the message
  * object. In case of the sja1000 @obj_base_addr is taken the same as the chips
  * base address.
  * Unless the hardware uses a segmented memory map, flags can be set zero.
@@ -228,7 +228,7 @@ int pcm3680_init_chip_data(struct candevice_t *candev, int chipnr)
 int pcm3680_init_obj_data(struct canchip_t *chip, int objnr)
 {
        chip->msgobj[objnr]->obj_base_addr=chip->chip_base_addr;
-       
+
        return 0;
 }
 
@@ -236,10 +236,10 @@ int pcm3680_init_obj_data(struct canchip_t *chip, int objnr)
  * template_program_irq - program interrupts
  * @candev: Pointer to candevice/board structure
  *
- * The function template_program_irq() is used for hardware that uses 
+ * The function template_program_irq() is used for hardware that uses
  * programmable interrupts. If your hardware doesn't use programmable interrupts
- * you should not set the @candevices_t->flags entry to %CANDEV_PROGRAMMABLE_IRQ and 
- * leave this function unedited. Again this function is hardware specific so 
+ * you should not set the @candevices_t->flags entry to %CANDEV_PROGRAMMABLE_IRQ and
+ * leave this function unedited. Again this function is hardware specific so
  * there's no example code.
  * Return value: The function returns zero on success or %-ENODEV on failure
  * File: src/template.c