#include <linux/io.h>
#include <linux/i2c.h>
#include <linux/platform_data/i2c-nomadik.h>
+#include <linux/platform_data/db8500_thermal.h>
#include <linux/gpio.h>
#include <linux/amba/bus.h>
#include <linux/amba/pl022.h>
#include <linux/smsc911x.h>
#include <linux/gpio_keys.h>
#include <linux/delay.h>
-#include <linux/of.h>
-#include <linux/of_platform.h>
#include <linux/leds.h>
#include <linux/pinctrl/consumer.h>
+#include <linux/platform_data/pinctrl-nomadik.h>
+#include <linux/platform_data/dma-ste-dma40.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
#include <asm/hardware/gic.h>
-#include <plat/ste_dma40.h>
-#include <plat/gpio-nomadik.h>
-
#include <mach/hardware.h>
#include <mach/setup.h>
#include <mach/devices.h>
.codec = &ab8500_codec_pdata,
};
+/*
+ * Thermal Sensor
+ */
+
+static struct resource db8500_thsens_resources[] = {
+ {
+ .name = "IRQ_HOTMON_LOW",
+ .start = IRQ_PRCMU_HOTMON_LOW,
+ .end = IRQ_PRCMU_HOTMON_LOW,
+ .flags = IORESOURCE_IRQ,
+ },
+ {
+ .name = "IRQ_HOTMON_HIGH",
+ .start = IRQ_PRCMU_HOTMON_HIGH,
+ .end = IRQ_PRCMU_HOTMON_HIGH,
+ .flags = IORESOURCE_IRQ,
+ },
+};
+
+static struct db8500_thsens_platform_data db8500_thsens_data = {
+ .trip_points[0] = {
+ .temp = 70000,
+ .type = THERMAL_TRIP_ACTIVE,
+ .cdev_name = {
+ [0] = "thermal-cpufreq-0",
+ },
+ },
+ .trip_points[1] = {
+ .temp = 75000,
+ .type = THERMAL_TRIP_ACTIVE,
+ .cdev_name = {
+ [0] = "thermal-cpufreq-0",
+ },
+ },
+ .trip_points[2] = {
+ .temp = 80000,
+ .type = THERMAL_TRIP_ACTIVE,
+ .cdev_name = {
+ [0] = "thermal-cpufreq-0",
+ },
+ },
+ .trip_points[3] = {
+ .temp = 85000,
+ .type = THERMAL_TRIP_CRITICAL,
+ },
+ .num_trips = 4,
+};
+
+static struct platform_device u8500_thsens_device = {
+ .name = "db8500-thermal",
+ .resource = db8500_thsens_resources,
+ .num_resources = ARRAY_SIZE(db8500_thsens_resources),
+ .dev = {
+ .platform_data = &db8500_thsens_data,
+ },
+};
+
+static struct platform_device u8500_cpufreq_cooling_device = {
+ .name = "db8500-cpufreq-cooling",
+};
+
/*
* TPS61052
*/
};
#endif
-static struct pl022_ssp_controller ssp0_plat = {
+struct pl022_ssp_controller ssp0_plat = {
.bus_id = 0,
#ifdef CONFIG_STE_DMA40
.enable_dma = 1,
};
#endif
-static struct amba_pl011_data uart0_plat = {
+struct amba_pl011_data uart0_plat = {
#ifdef CONFIG_STE_DMA40
.dma_filter = stedma40_filter,
.dma_rx_param = &uart0_dma_cfg_rx,
#endif
};
-static struct amba_pl011_data uart1_plat = {
+struct amba_pl011_data uart1_plat = {
#ifdef CONFIG_STE_DMA40
.dma_filter = stedma40_filter,
.dma_rx_param = &uart1_dma_cfg_rx,
#endif
};
-static struct amba_pl011_data uart2_plat = {
+struct amba_pl011_data uart2_plat = {
#ifdef CONFIG_STE_DMA40
.dma_filter = stedma40_filter,
.dma_rx_param = &uart2_dma_cfg_rx,
&snowball_key_dev,
&snowball_sbnet_dev,
&snowball_gpio_en_3v3_regulator_dev,
+ &u8500_thsens_device,
+ &u8500_cpufreq_cooling_device,
};
static void __init mop500_init_machine(void)
/* This board has full regulator constraints */
regulator_has_full_constraints();
-
- mop500_uib_init();
}
static void __init snowball_init_machine(void)
/* This board has full regulator constraints */
regulator_has_full_constraints();
-
- mop500_uib_init();
}
MACHINE_START(U8500, "ST-Ericsson MOP500 platform")
.timer = &ux500_timer,
.handle_irq = gic_handle_irq,
.init_machine = snowball_init_machine,
- .init_late = ux500_init_late,
+ .init_late = NULL,
MACHINE_END
-
-#ifdef CONFIG_MACH_UX500_DT
-
-struct of_dev_auxdata u8500_auxdata_lookup[] __initdata = {
- /* Requires call-back bindings. */
- OF_DEV_AUXDATA("arm,cortex-a9-pmu", 0, "arm-pmu", &db8500_pmu_platdata),
- /* Requires DMA and call-back bindings. */
- OF_DEV_AUXDATA("arm,pl011", 0x80120000, "uart0", &uart0_plat),
- OF_DEV_AUXDATA("arm,pl011", 0x80121000, "uart1", &uart1_plat),
- OF_DEV_AUXDATA("arm,pl011", 0x80007000, "uart2", &uart2_plat),
- /* Requires DMA bindings. */
- OF_DEV_AUXDATA("arm,pl022", 0x80002000, "ssp0", &ssp0_plat),
- OF_DEV_AUXDATA("arm,pl18x", 0x80126000, "sdi0", &mop500_sdi0_data),
- OF_DEV_AUXDATA("arm,pl18x", 0x80118000, "sdi1", &mop500_sdi1_data),
- OF_DEV_AUXDATA("arm,pl18x", 0x80005000, "sdi2", &mop500_sdi2_data),
- OF_DEV_AUXDATA("arm,pl18x", 0x80114000, "sdi4", &mop500_sdi4_data),
- /* Requires clock name bindings. */
- OF_DEV_AUXDATA("st,nomadik-gpio", 0x8012e000, "gpio.0", NULL),
- OF_DEV_AUXDATA("st,nomadik-gpio", 0x8012e080, "gpio.1", NULL),
- OF_DEV_AUXDATA("st,nomadik-gpio", 0x8000e000, "gpio.2", NULL),
- OF_DEV_AUXDATA("st,nomadik-gpio", 0x8000e080, "gpio.3", NULL),
- OF_DEV_AUXDATA("st,nomadik-gpio", 0x8000e100, "gpio.4", NULL),
- OF_DEV_AUXDATA("st,nomadik-gpio", 0x8000e180, "gpio.5", NULL),
- OF_DEV_AUXDATA("st,nomadik-gpio", 0x8011e000, "gpio.6", NULL),
- OF_DEV_AUXDATA("st,nomadik-gpio", 0x8011e080, "gpio.7", NULL),
- OF_DEV_AUXDATA("st,nomadik-gpio", 0xa03fe000, "gpio.8", NULL),
- OF_DEV_AUXDATA("st,nomadik-i2c", 0x80004000, "nmk-i2c.0", NULL),
- OF_DEV_AUXDATA("st,nomadik-i2c", 0x80122000, "nmk-i2c.1", NULL),
- OF_DEV_AUXDATA("st,nomadik-i2c", 0x80128000, "nmk-i2c.2", NULL),
- OF_DEV_AUXDATA("st,nomadik-i2c", 0x80110000, "nmk-i2c.3", NULL),
- OF_DEV_AUXDATA("st,nomadik-i2c", 0x8012a000, "nmk-i2c.4", NULL),
- /* Requires device name bindings. */
- OF_DEV_AUXDATA("stericsson,nmk_pinctrl", 0, "pinctrl-db8500", NULL),
- /* Requires clock name and DMA bindings. */
- OF_DEV_AUXDATA("stericsson,ux500-msp-i2s", 0x80123000,
- "ux500-msp-i2s.0", &msp0_platform_data),
- OF_DEV_AUXDATA("stericsson,ux500-msp-i2s", 0x80124000,
- "ux500-msp-i2s.1", &msp1_platform_data),
- OF_DEV_AUXDATA("stericsson,ux500-msp-i2s", 0x80117000,
- "ux500-msp-i2s.2", &msp2_platform_data),
- OF_DEV_AUXDATA("stericsson,ux500-msp-i2s", 0x80125000,
- "ux500-msp-i2s.3", &msp3_platform_data),
- {},
-};
-
-static const struct of_device_id u8500_local_bus_nodes[] = {
- /* only create devices below soc node */
- { .compatible = "stericsson,db8500", },
- { .compatible = "stericsson,db8500-prcmu", },
- { .compatible = "simple-bus"},
- { },
-};
-
-static void __init u8500_init_machine(void)
-{
- struct device *parent = NULL;
- int i2c0_devs;
- int i;
-
- /* Pinmaps must be in place before devices register */
- if (of_machine_is_compatible("st-ericsson,mop500"))
- mop500_pinmaps_init();
- else if (of_machine_is_compatible("calaosystems,snowball-a9500"))
- snowball_pinmaps_init();
- else if (of_machine_is_compatible("st-ericsson,hrefv60+"))
- hrefv60_pinmaps_init();
-
- parent = u8500_of_init_devices();
-
- for (i = 0; i < ARRAY_SIZE(mop500_platform_devs); i++)
- mop500_platform_devs[i]->dev.parent = parent;
-
- /* automatically probe child nodes of db8500 device */
- of_platform_populate(NULL, u8500_local_bus_nodes, u8500_auxdata_lookup, parent);
-
- if (of_machine_is_compatible("st-ericsson,mop500")) {
- mop500_gpio_keys[0].gpio = GPIO_PROX_SENSOR;
-
- platform_add_devices(mop500_platform_devs,
- ARRAY_SIZE(mop500_platform_devs));
-
- mop500_sdi_init(parent);
- mop500_audio_init(parent);
- i2c0_devs = ARRAY_SIZE(mop500_i2c0_devices);
- i2c_register_board_info(0, mop500_i2c0_devices, i2c0_devs);
- i2c_register_board_info(2, mop500_i2c2_devices,
- ARRAY_SIZE(mop500_i2c2_devices));
-
- mop500_uib_init();
-
- } else if (of_machine_is_compatible("calaosystems,snowball-a9500")) {
- mop500_of_audio_init(parent);
- } else if (of_machine_is_compatible("st-ericsson,hrefv60+")) {
- /*
- * The HREFv60 board removed a GPIO expander and routed
- * all these GPIO pins to the internal GPIO controller
- * instead.
- */
- mop500_gpio_keys[0].gpio = HREFV60_PROX_SENSE_GPIO;
- platform_add_devices(mop500_platform_devs,
- ARRAY_SIZE(mop500_platform_devs));
-
- mop500_uib_init();
- }
-
- /* This board has full regulator constraints */
- regulator_has_full_constraints();
-}
-
-static const char * u8500_dt_board_compat[] = {
- "calaosystems,snowball-a9500",
- "st-ericsson,hrefv60+",
- "st-ericsson,u8500",
- "st-ericsson,mop500",
- NULL,
-};
-
-
-DT_MACHINE_START(U8500_DT, "ST-Ericsson U8500 platform (Device Tree Support)")
- .smp = smp_ops(ux500_smp_ops),
- .map_io = u8500_map_io,
- .init_irq = ux500_init_irq,
- /* we re-use nomadik timer here */
- .timer = &ux500_timer,
- .handle_irq = gic_handle_irq,
- .init_machine = u8500_init_machine,
- .init_late = ux500_init_late,
- .dt_compat = u8500_dt_board_compat,
-MACHINE_END
-#endif
projects / can-eth-gw-linux.git / blobdiff